Emos P5683 Manual

Emos Termostat P5683

Læs gratis den danske manual til Emos P5683 (19 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Emos P5683, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/19

2101107000_31-P5683_00_01_WEB 105 × 148 mm

P5683

GB Surface Mount Thermostat

CZ Příložný termostat

SK Príložný termostat

PL Termostat przylgowy

HU Érintkezős termosztát

SI Naležni termostat

RS|HR|BA|ME Termostat s obujmicom

DE Anlegethermostat

UA Прикладний термостат

RO|MD Termostat de contact

LT Pridedamas termostatas

LV Piestiprināmais termostats

EE Pindpaigaldusega termostaat

BG Термостат за монтаж върху повърхност

FR Thermostat d‘applique

IT Termostato a contatto

ES Termostato integrado

NL Oplegthermostaat

www.emos.eu

insulation on the installation spot must be removed before

mounting the sensor. To achieve a more accurate temperature

measurement, it is recommended to use a heat conductive

paste and clean the contact surface of dirt.)

2. Any excess spring can be cut o.

Electrical Connection

1. Remove the 2 screws on the front housing of the thermostat.

2. Carefully remove the front housing.

3. Connect in accordance with the following diagram (see Fig. 2):

Pump

– 230 VPower

– jumperJump

– protective earth, prevents injury by electrical current PE

4. The thermostat features a screwless conductor connection.

Press downwards onto the top plastic connector with e.g. a

screwdriver. The terminal contact will release. Plug in the

conductor. Repeat the process for all conductors needed for

connection. Replace the screws.

The device may only be installed by a professional plumber in

accordance with the connection diagram. In addition, the connection

must meet up-to-date, valid standards and specications of your

energy provider. Installation must always be performed when power

is turned o; follow safety specications. Maintain the maximum

switched load listed in technical specications! The manufacturer is

not liable for inexpert installation.

Putting the Device into Operation

Connect the thermostat with pump according to instructions.

Connect the thermostat to 230 V power supply.

Short-press the button.

The currently set mode and heating/cooling mode setting will ash

on the display (e.g.: F1/C1).

Then, the current temperature will be displayed.

Temperature Setting

Set your temperature of choice by repeatedly pressing the up

/down arrow.

Holding the arrow adjusts value faster.

Once temperature is set, wait several seconds until the value is

automatically saved.

The display will then automatically show the current measured

temperature.

To check your temperature setting, press the up or down arrow once.

Example: with temperature set to 50 °C, press the up or down arrow

once. The display will show C 50.0.

Selecting Heating or Cooling Mode

Enter settings by long-pressing the down arrow for approxi-

mately 3 seconds.

Use the arrows to choose between heating mode (C1 on the display)

or cooling mode (C2 on the display).

Once the value of choice is set, wait several seconds until the value

is automatically saved.

The display will then automatically show the current measured

temperature.

Dierences for cooling mode:

Switching in cooling mode is reversed: The thermostat activates

the system if the measured temperature is higher than the set

temperature.

Hysteresis

Hysteresis is the dierence in temperature required for switching

on and o.

If, for example, you set the temperature in heating mode to 42.5 °C

and the hysteresis value to 2.5 °C, the thermostat will activate your

system as soon as room temperature drops to 40 °C and deactivate

it when temperature reaches 42.5 °C.

Enter settings by long-pressing the up arrow for approximately

3 seconds.

Set your hysteresis value of choice by repeatedly pressing the up

/down arrow.

Holding the arrow adjusts value faster.

Once the value of choice is set (e.g. 2.5 °C, displayed as d 2.5) wait a

few seconds until the setting is automatically saved.

The display will then automatically show the current measured

temperature.

Upkeep and Maintenance

The product is designed to serve reliably for many years if used

properly. Here are some tips for proper operation:

• Read the manual carefully before using this product.

• Do not expose the product to direct sunlight, extreme cold

and humidity and sudden changes in temperature. This would

reduce accuracy of detection.

• Do not place the product in locations prone to vibration and

shocks – may cause damage.

• Do not subject the product to excessive force, impacts,

dust, high temperatures or humidity – doing so may cause

malfunction, shorten battery life, damage batteries and

deform plastic parts.

• Do not expose the product to rain or high humidity, dropping

or splashing water.

• Do not place any open ame sources on the product such

as a lit candle, etc.

• Do not place the product in places with inadequate air ow.

• Do not insert any objects into the product‘s vents.

• Do not tamper with the internal electrical circuits of the product

– doing so may damage the product and will automatically

void the warranty. The product should only be repaired by a

qualied professional.

• To clean the product, use a slightly moistened soft cloth. Do not

use solvents or cleaning agents – they could scratch the plastic

parts and cause corrosion of the electric circuits.

• Do not immerse the product in water or other liquids.

• In the event of damage or defect of the product, do not

perform any repairs by yourself. Have it repaired in the shop

where you bought it.

Produkt Specifikationer

Mærke:	Emos
Kategori:	Termostat
Model:	P5683

Har du brug for hjælp?

Hvis du har brug for hjælp til Emos P5683 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Emos Manualer

2 September 2024

28 August 2024

28 August 2024

25 August 2024

13 August 2024

7 August 2024

31 Juli 2024

30 Juli 2024

28 Juli 2024

26 Juli 2024

Termostat Manualer

Nyeste Termostat Manualer

Fantini Cosmi C900R Manual

13 August 2025

GE RAK190V Manual

12 August 2025

Honeywell CT50K1028/E Manual

12 August 2025

Honeywell RET97B5D1002/U Manual

12 August 2025

Honeywell RCHT9510WFW2001/W Manual

12 August 2025

Honeywell CT87K1004/E1 Manual

12 August 2025

Honeywell YCT87N1006 Manual

12 August 2025

Honeywell RTH7500D1049/A Manual

12 August 2025

Honeywell YCT50K1006 Manual

12 August 2025

Honeywell RTH2510B1000/U Manual

12 August 2025