Epson PowerLite 1730W Manual

Epson videoprojektorer PowerLite 1730W

Læs gratis den danske manual til Epson PowerLite 1730W (3 sider) i kategorien videoprojektorer. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Epson PowerLite 1730W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Before using the projector, make sure you read the safety instructions in

the User’s Guide on your projector CD.

1 Locate the required cables:

2 Connect the computer cable to

the blue Computer (Component Video)

port on the projector.

3 Connect the other end to your notebook’s

video-out or monitor port.

4 Connect the power cord to the

projector, then plug the other end

into an electrical outlet.

1 Turn on your notebook.

2 Open the slide (lens cover).A/V Mute

NOTE: The slide must be

opened completely.

3 Make sure the light Power

is orange and not flashing.

4 Press the button Power

to turn on the projector.

The projector beeps once,

and the light flashes Power

green and then stays on.

Turn on your equipment

Connect the projector

to your notebook

Follow these instructions to connect the projector to your

notebook. For other setup options, see your User’s Guide.

PowerLite® 1720/1730W

Quick Setup

VGA computer cable

1 If you’ve turned on your notebook and switched it to external display,

but you don’t see an image, press the button on the Source Search

projector or the button on the remote control to select the Search

image source.

NOTE: If you still see a blank screen or have other display problems,

see the troubleshooting tips on the back of this sheet.

2 To raise the image, press

the foot release button

for the front adjustable

foot and lift the front.

Release the button to

lock the foot in position.

3 Turn the focus ring to sharpen the image.

Turn the zoom ring to reduce or

enlarge the image.

4 If your image looks like or , you’ve placed the projector off

to one side of the screen at an angle. Place it directly in front of the

center of the screen, facing the screen squarely.

5 If your image looks like or , press the or button

on the projector to correct it.

Adjust the image

To shut down the projector, press the button twice and Power

simply unplug it. You don’t have to wait for the projector to cool off.

Turn over

Power light

Power button

Zoom

Focus

Power cord

*411482100*

If this is your first time using the remote, make sure its batteries

are installed as shown (two AA batteries).

You can use the remote control to operate the projector. With the USB

cable, you can also use the remote to change presentation slides. For more

information on using the remote control, see your ’ .User s Guide

Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

Printed in XXXXXX

Quick Setup

PowerLite 1720/1730W

CPD-25570

Using the remote control

Where to get help

For more information about using the projector, install the ’ User s Guide

from your projector CD.

Telephone Support Services

To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter

the PIN on the Epson PrivateLine Support card included with your projector.

This service is available 6 to 6 , Pacific Time, Monday through AM PM

Friday, for the duration of your warranty period. You may also speak with

a projector support specialist by dialing one of these numbers:

U.S.: (562) 276-4394, 6 to 6 , Pacific Time, Monday through Friday AM PM

Canada: (905) 709-3839, 6 to 6 , Pacific Time, Monday through FridayAM PM

Days and hours of support are subject to change without notice. Toll or long

distance charges may apply.

Internet Support

Visit Epson’s support website at and select your epson.com/support

product for solutions to common problems. You can download utilities and

documentation, get FAQs and troubleshooting advice, or e-mail Epson with

your questions.

Visit http://www.presentersonline.com to access tips, templates, and

training for developing successful presentations.

If you see a blank screen...

If you see a blank screen or the message after turning on No signal

your notebook, check the following:

 Make sure the light on the projector is green and not flashing, Power

and the slide is open.A/V Mute

 Press the button on the projector or the button Source Search Search

on the remote control to select the computer as the image source.

 Press the function key on your keyboard that lets you display on an

external monitor. It may be labeled or have an icon such asCRT/LCD

. You may have to hold down the key on the notebook while Fn

pressing it. Allow a few seconds for the projector to sync up after

changing the setting.

If the projector and notebook

don’t display an image...

If your image displays either on the projector or notebook, but not on

both, follow the steps below. Note that some notebooks cannot display

the same resolution and/or aspect ratio on both the LCD screen and the

projected image.

Windows

Try using the or key as described above. On most systems, CRT/LCD

this key lets you toggle between the LCD screen and the projector,

or display on both at the same time.

If that doesn’t work, check your monitor settings to make sure both the

LCD screen and the external monitor port are enabled.

1. From the Windows® Control Panel, open the utility. In Display

Windows Vista®, right-click on the desktop and select , Personalize

then select .Display Settings

2. In the Display Properties dialog box, click

the tab, then click . In Settings Advanced

Windows Vista, click .Advanced Settings

3. The method for adjusting the setting varies;

you may have to click a tab, then Monitor

make sure the external Monitor port is set

as your primary display and/or enabled.

See your notebook’s manual or online help

for details.

Mac OS®

1. From the Apple® menu, select System

Preferences Display, then select

or .Displays

2. Click .Detect Displays

3. Select the or VGA Display Color LCD

dialog box.

4. Click the or tab Arrangement Arrange

and click .Mirror Displays

Troubleshooting

Turn off projector

display and sound

Display next or

previous slide

Navigate projector menus

Control projector volume

customer-only offers. You can use the registration card or CD included

with your projector, or register online at www.epson.com/webreg.

Turn projector on

and off Choose which source

to display

Change aspect ratio

Access projector

menu system

Produkt Specifikationer

Mærke:	Epson
Kategori:	videoprojektorer
Model:	PowerLite 1730W
Vægt:	1700 g
Lampe type:	UHE
Udgangseffekt (RMS):	1 W
Antal USB 2.0-porte:	1
Komponentvideo (YPbPr/YCbCr) indgang:	1
Strømforbrug (standby):	4 W
Strømforbrug (typisk):	243 W
Driftstemperatur (T-T):	5 - 35 °C
Markedspositionering:	Bærbar
Dimensioner (BxDxH):	284.48 x 200.66 x 71.12 mm
Sammensat videoindgang:	1
Støjniveau:	39 dB
Fjernbetjening inkluderet:	Ja
Effektkrav:	100 – 240 V ±10%, 50/60 Hz AC
Luftfilter:	Ja
Antal indbyggede højttalere:	1
Slot til kabellås:	Ja
Lydindgang:	1
Billedformat:	16:10
Fokus:	Vejledning
Antal farver:	16,78 millioner farver
Kontrastforhold (typisk):	2000:1
Kabellåseslids type:	Kensington
Brændviddeområde:	16.1 - 19.3 mm
F-number (relativ aperture):	1.58
Projektor lysstyrke:	3000 ANSI lumens
Projektionsteknologi:	LCD
Projektor indbygget opløsning:	WXGA (1280x800)
Skærmstørrelse kompatibilitet:	30 - 300 "
Trapezkorrektion, vertikal:	30 °
Levetid for lyskilde:	3000 t
Lampeeffekt:	170 W
Levetid for lyskilde (økonomisk tilstand):	4000 t
Lyskilde type:	Lampe
Antal af S-video-indgange:	1
Video indgang:	NTSC/NTSC4.43/PAL/M-PAL/N-PAL/ PAL60/SECAM SDTV/HDTV