Eureka K2-XT Manual

Eureka Fuld K2-XT

Læs gratis den danske manual til Eureka K2-XT (2 sider) i kategorien Fuld. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Eureka K2-XT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Fig.1

ASSEMBLY INSTRUCTIONS

FOR THE K2-XT

Component List: 1 Tent Body 1 Fly 4 Poles

1 Vestibule Rod 1 Carry Bag 1 Pole Bag 1 Bag w/ Stakes

Assembly:

1 and separate the components. Unpack the carry bag

Unfold the tent body and lay it out with the ﬂoor on the

ground and a grommeted web in each corner. Pull the

tent into a rough hexagon. Do not stake down the tent

just yet; but in windy conditions, stake down one corner

that faces into the wind.

2 Assemble the shockcorded tent poles and rod.

Carefully seat each section. Try to keep the poles from

snapping together as this can damage the ends. Set the

shorter vestibule rod aside.

3 . Insert the tent poles into the mesh sleeves

• Near the side of the door, insert and slide a pole

through the continuous mesh sleeve from to . Push A B

the pole rather than pull it.

• At the other side of the door, insert and slide a second

pole from to . C D

• Insert and slide the remaining two poles through the

mesh sleeves from to and from to . See ﬁg.1.E F G H

4 Raise the tent.

• At location A, grasp the end of the pole and

insert the post into the ﬁrst grommet (the one

closest to the tent) on the web. At location B,

lift the tent and push the pole from to to B A

create an arc. Insert the locking post into one

of the grommets on web to maintain tension.

There are 2 or 3 grommets on each web —

these are for adjustment. If possible, insert the

posts into the grommets closest to the tent to make

the canopy tight and wrinkle free.

• Repeat with the second pole from C D to .

• Move to the side of the tent and insert the locking post into the ﬁrst

grommet on the side web at . On the opposite side and at location E

F F E grasp the end of the pole and push from to to form an arc.

Insert the post into a grommet on the web.

• Continue with the last pole

from to . See ﬁg.2 and fig.3. G H

6 Attach the ﬂy to the tent.

• Spread the ﬂy on the

ground. Find the front

vestibule; it has a door and

clear plastic window. Drape

the ﬂy, right side up, on top of

the tent so that the vestibule

covers one of the doors.

• Reach under the ﬂy and attach

all the Velcro

tabs, through the

openings in the sleeves, to the

poles. See ﬁg.4.

• Connect the six side release buckles

on the ﬂy to their mates on the tent.

See ﬁg.5.

• Move to the rear of the tent and stake

out the web loop on the back

vestibule, but do not adjust the

tension just yet. Go to the front of tent

and stake out the two web loops on

the front vestibule. See ﬁg.7.

7 until the vestibule Tighten the webs

is taut. Work your way around the

tent, tighten the six side release

buckle webs from the ﬂy and from

the rear stake out web. See Fig.8.

8 Stake out the attached guy lines

and adjust the sliders to a proper

tension. See ﬁg.9.

REV D 4.09

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.9

Fig.8

Fig.7

Your tent is now ready for use.

Open the two fly roof vents through the zippered slots in the

tent roof. Then, roll up the vestibule door from the bottom or to

the side for better ventilation. The front vestibule also features

an attached snow flap around the bottom.

Take down :

Pull up stakes. Release the ﬂy’s Velcro

and

buckles. Remove ﬂy and open door. Pull posts out of the

grommets and push poles out of the sleeves. Collapse the tent

poles and stow. Fold the tent onto itself and fold the ﬂy and lay

it on tent. Roll up both towards the door and stow.

5 Stake the tent down.

Your tent is now free

standing. Place it in the

desired location and

stake it down. Be sure to

drive the stakes through

the web loops or rings-

not the grommets.

• Insert the posts of the

vestibule pole into the

grommets on the web at

either side of the door.

Connect the ﬁve clips on the

ﬂy to the poles. See ﬁg.6.

Produkt Specifikationer

Mærke:	Eureka
Kategori:	Fuld
Model:	K2-XT

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka K2-XT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fuld Eureka Manualer

Eureka Juno 3XTA Manual

21 Maj 2024

Eureka Headquarters Manual

5 April 2024

Eureka Midori 4 Manual

30 Marts 2024

Eureka Midori 2 Manual

20 Marts 2024

Eureka Grayback Manual

16 Marts 2024

Eureka Tetragon Manual

21 Februar 2024

Eureka Taron 2 Manual

19 Januar 2024

Eureka Jade Canyon 6 Manual

9 December 2023

Eureka Copper Canyon 1610 Manual

23 November 2023

Eureka K2-XT Manual

7 November 2023

Fuld Manualer

Nyeste Fuld Manualer

Deryan 4P Pop-Up Tent Manual

11 December 2025

Deryan Dome 2P XL Tent Manual

10 December 2025

Vevor 120813 Manual

2 December 2025

Vevor ORGTK8080180 Manual

30 November 2025

Vevor ORGTK100100200 Manual

30 November 2025

Vevor CPT3W1D Manual

23 November 2025

Vevor AUTO4ALU Manual

23 November 2025

Vevor INDIAN4W Manual

22 November 2025

Vevor 120904 Manual

21 November 2025

Vevor 120838 Manual

20 November 2025