Eureka Opal SRS4 Insert Manual

Eureka Varmeapparat Opal SRS4 Insert

Læs gratis den danske manual til Eureka Opal SRS4 Insert (6 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Eureka Opal SRS4 Insert, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Operation & Installation Instruction

Opal SRS4 Insert

Please keep these instrution for future reference.Rev B231311

Opal SRS4 Insert 12

A.F. Gason Pty Ltd reserves the right to modify or alter specications, material etc. in the intrest of product improvement

WARRANTY

1. Subjects to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason warrants the follow components of its heaters against defects in workmanship

and/or materials for the following periods from the date of purchase:

a) the rebox for ten years;

b) the paint nish for a period of twelve months if the purchaser has followed the instruction provided by Gason in the Operati on and Installation Instructions manual; and

c) all other components for twelve months execpt the glass, re brick lining or bae plate if, in the opinion of Gason, these items have been damaged by impact.

2. This exte nded warranty does not apply;

a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;

b) if, in the opinion of Gason, the heater or any other component has been subject to abuse, misuse, alteration, modication or has not been installed, operated or maintained in

accordance with the instructions provided by Ga son; or,

c) to owners other then the original purchaser.

3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason servi ce

centre to arrange for an assessment.

4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:

a) re place the heater;

b) repair or replace specic components of the heater; or

c) provide a full refund.

5. Parts replaced under warranty are warranted for the balance of their original warranty period.

6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this

Warranty must pay all costs associated w ith:

a) returning the heater; and

b) the delivery or collection of any new or repaired heater.

Our goods come with guarantees that cannot be excluded under the Austrlian Consumer Law. You are entilted to a replacement or refund for a major failure and for

compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or repla ced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

Any benets you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which

these warranties relate.

These warranties are given by:

A.F. Gason Pty Ltd

Blake Street

Ararat VIC 3377

Please contact us if y ou have any queries on:

Phone: 03 53522151

or email us via the “Contact Us” section of our website: www.gason.com.au

•Smoke entering the room from the rebox when the door is open may be caused by

•Insucient length of ue (Flue to be 4500mm minimum underneath the base of heater to

underside of cowl)

Increase height of ue

•Flue downdraught

Consult dealer or increase height of ue.

•Creosote buildup in ue

Remove cowl and clean ue as per cleaning instructions. Check moisture content of wood.

•Excessive ash build up

some woods will give large amounts of ash despite how you run the h eater. Others will give you very little.

Use the wood which is most convenient for you as long as it is dry. After a period of time you will get to

know when to empty your unit. Bark will give you excessive ash. Try not to burn it.

If you are burning wood that gives you charcoal, you may nd that after running the heater say for 8 hours

at maximum burn rate, the charcoal builds up excessively. Overnight burn will reduce this charcoal back to

a ne ash. If you are not ready to shut down for overnight burn when you next fuel the stove, load the

stove with only one piece of wood and lay it across the rebox on top of the charcoal. Open the air control

wide open and you will nd the charcoal will burn down with the one piece of wood. Repeat the process

until the ash level is signicantly reduced.

Troubleshooting (Continued)

Opal SRS4 Insert 2 Opal SRS4 Insert 11

Read and follow these instructions carefully before installing and

sing this appliance

AVE THESE INSTRUCTIONS

WARNING

Safety Warnings

•

A ue re with resulting damage may occur if the appliance is not installed,

operated and maintained as per this booklet.

• Never place combustible materials such as wood, paper or furniture near the

appliance.

• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,

flammable liquids or any substance containing salts or corrosives.

• This appliance must not be installed and operated in an area where kerosene,

petrol, paint thinner or other ammable liquid is used or stored.

• The ue system must be inspected and cleaned annually or sooner if required.

Failure to do so could result in an excessive buildup of creosote which may

result in a ue re which may damage the ue or cause damage to your home.

• The surface of the appliance becomes hot during operation. Do not touch the

surface of this appliance. Keep children away from this appliance during

operation. Do not allow anyone to operate this appliance who is not familiar

with this instruction booklet.

WARNING

Paint curing and care

Your heater is coated with the best available heat resistant paint. Even though

he paint has been baked after application, it may require further temperature

uring. It may, if you overre the heater on its rst re, discolour. For your rst

wo or three rings, never exceed medium air setting and always have the fan

n when above low burn. Do not wipe the heater while the paint is curing. After

he paint has cured the only maintenance required to maintain the heaters nish

s to wipe it with a soft cloth. Do not use any commercial cleaners or solvents on

he paint nish.

e are proud of the presentation of our products. If at any time you need to

reshen up the paint, your local dealer has touchup paint available for purchase.

ou may even change the colour of your heater if you wish.

If you have any enquiries, please contact the dealer from whom you purchased your heater:

LEASE COMPLETE:

ealer Name

ealer Address

Phone:

lease attach your original purchase dockets to this booklet for future reference.

Troubleshooting

• isy FanNo

Turn the power o and remove the three pin plug from the power point .

Remove the four screws that hold the front fan access panel . . Remove the panel

Disconnect the wiring loom via the plastic joine r. .Unscrew the nut which holds the fan in position and remove the fan

Clean any dust with dry paint brush and acuum the fan blade Clean around the moto a v s. r. After completion place tw o

or three drops of sewing machine oil on the shafts at the bearing Replace the fan in reverse to the remo al s. v .

• F an not workin g

Check the power connection with another applianc If the power point is e. O.K assume the. Fan or the Switch is

defectiv Isolate the power as abov Check that the terminals on the loom and the switch are rmly connected If the. e. . e

fan then fails to function , awayremove the fan and switch by rstly removing the knob o the fan switch by pulling it

from the heate r. . eUndo the holding nut and pull the switch out Disconnect the wiring from the power lead and remov

the fan and switch . e.Convey the same to the authorised Eureka Dealer from whom you purchased your unit for servic

Replace in the reverse orde r.

• rAir Cont ol ammin J g

Lift up o e. and rem ve top plat

Rem ve airo co knntrol ob by tur ing anti-clockwi n s Lift ol out the way.e. air contr panel of

Th ng the ace. Un ve the a e. ere are three bolts holdi air slide in pl do them and remo ir slid Wipe any h yas or dust that ma

have accumul ted a on a sthe back of the ir lide or on the face the heate of r. v on the eIf any burrs have de eloped back of th

air lide or s on f of r, o a ve a andthe ace the heate rub them with ne wet nd dry sand paper till you ha smooth surface

edges. a ke wa aRepl ce the air slide and ma sure the shers and sp cers re a on w othe bolts hen you screw the bolts back int

the ace of the f heater. a of nt s whDo not apply ny type lubrica to the air lide atsoever as th a ke theis will attract dust nd ma

slide stick .

• iNo Overn ght Bur n

Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heate r. isIf it

loos tighten up the bolts holding the air slidee, to the face of the heate r. .Do not overtighten

Check that the door rope has an even indentation from the sealing stri which is on the p, face of the rebox . nIf it is uneve

and it appears as though air could leak through the seal , adjust the thickness of the door rope to suit . toStretch the rope

make it thinner where the indentation is the heaviest and bunch up the excess where the indentation is smalle r.

Check the four bolts that hold the glass retainer in position . . .If loose tighten Do not overtighten

The door may become loose through the door seal shrinking . To tighten the doo r, ofopen the door and look at the inside

the door shaft . UnscrewAllen key screw in door handle shaft . Rotate door handle shaft anti-clockwise when facing heater

(1 turn = 1 . . millimetre) Close door and lock Open door and check door for even indentation from sealing stri Repea p. t

process if required . Replace Allen key screw (check to ensure that roll pin is central in shaft.)

When closing the door you should now feel rm resistance when the latch comes into contact with the catch .

WARNING

Overring

NEVER OPERATE THE HEATER WITH THE DOOR LOOSE AND DO NOT AIR TIGHT

OVERFIRING COULD RESULT IN DETRIMENTAL WEAR AND TEAR ON THE

FIREBOX.

Produkt Specifikationer

Mærke:	Eureka
Kategori:	Varmeapparat
Model:	Opal SRS4 Insert

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Opal SRS4 Insert stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Eureka Manualer

Eureka Stockade SRS5 Insert Manual

22 August 2024

Eureka Opal SRS4 Insert Manual

22 August 2024

Eureka Garnet SRS3 Insert Manual

22 August 2024

Eureka Opal SRS3 Freestanding Manual

10 August 2024

Eureka Solitaire SRS2 Manual

29 Juli 2024

Eureka Pearl Insert Manual

2 Marts 2024

Eureka Garnet SRS2 Freestanding Manual

11 Oktober 2023

Eureka Jewel Freestanding Manual

12 August 2023

Eureka Nugget Mk2 Manual

1 November 2022

Eureka Ruby Freestanding Manual

12 Oktober 2022

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

BEKO RHO8323BT Manual

14 Juni 2025

DeWalt DXAM-2260 Manual

14 Juni 2025

AlorAir Zeus 900 Manual

14 Juni 2025

XPower B-55 Manual

14 Juni 2025

XPower B-2 Manual

14 Juni 2025

XPower M-27 Manual

14 Juni 2025

B-Air Vent VP-34 Manual

14 Juni 2025

XPower P-80 Manual

14 Juni 2025

DeLonghi JRE0812 Manual

14 Juni 2025

Aura CF15120B Manual

14 Juni 2025