Extech RH200W Manual

Extech Ikke kategoriseret RH200W

Læs gratis den danske manual til Extech RH200W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Extech RH200W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

USER MANUAL for MODEL RH200W

Wireless Hygro-Thermometer

Thank you for selecng the Extech RH200W Wireless Hygro-Thermometer with

Self-Calibraon & Auto Night Light. This device is shipped fully tested and

calibrated and, with proper use, will provide years of reliable service. Please

visit our website ( ) to check for the latest version of this User www.extech.com

Manual, Product Updates, and Customer Support.

DESCRIPTIONS

MAIN UNIT

1. Backlight key

In normal mode, short press for 5 seconds

of backlighng Pressing other keys will reset the .

5-second mer

2. OUT (CHANNEL) / + key

In calibraon mode, short press to increase the

value

In normal mode, short press to switch between

INDOOR, Channel 1~8

In normal mode, long press to enter

auto-cycle (Channel 1~8 and INDOOR

readings will alternately display at 4-

second intervals and the icon will

display). From -cycle mode, short auto

press to return to normal mode.

3. M (MODE) key

In calibraon mode, short press for

opons.

In calibraon mode, long press to clear data

4. MIN-MAX - key/

In calibraon mode, short press to decrease value

In normal mode, short press to check maximum/minimum temperature and

humidity records. Short press to return to normal mode

With MAX or MIN displayed, long press to reset the displayed values

5. CAL key

In normal mode, long press to enter calibraon mode

In calibraon mode, long press to return to normal mode

6. Auto night-light switch

Slide to ON posion to acvate night-light (the light will automacally turn

on in dark areas). The brightness is weaker than normal backlight. Slide to

OFF posion to turn o the night-light funcon

7. °C / °F key - Short press to toggle temperature units °C/°F

8. SENSOR key

In normal mode, short press to acvate the receiver for the current channel.

The unit will receive signals for 5 minutes

9. RESET key

Short press for a factory default reset. Perform a reset if the display freezes

or the unit otherwise malfuncons.

WIRELESS SENSOR

1. Transmission status LED lashes (f

when sensor is transming)

2. Wall mount

3. CHANNEL slide switch (assign

sensor to Channel 1 ~ 8)

4. RESET key (short press to reset

the sensor)

5. Baery compartment (2 x AA

baeries)

OPERATION

POWERING THE WIRELESS SENSOR

1. Remove the baery door of the sensor

2. Insert 2 ‘AA’ baeries, observing correct polarity

3. Close the baery door

Notes: Once a sensor is assigned a channel using the channel slide switch, you

can only -assign a channel by removing the baeries or reseng the unit. re

Avoid placing the sensor in direct sunlight or inclement weather.

POWERING THE MAIN UNIT

1. Remove the baery door of the main unit

2. Install 4 baeries observing correct polarity then use a paper clip to ‘AA’;

press the key RESET

3. Close the baery door

4. All LCD segments will switch on

Note: To avoid a pairing failure, power up the sensor rst, and then press the

RESET key on the main unit only.

INDOOR TEMPERATURE/RELATIVE HUMIDITY

1. Short press OUT unl ‘IN” is displayed. The unit is now displaying indoor

temperature °C / °F and Relave Humidity %.

2. Short press to switch between °C and °C / °F °F

3. When the temperature is <-40°F/°C or > 158°F (70°C), will be Lo or HI

displayed respecvely. The humidity display will show dashes:

4. When the humidity is < 1% or > 99%, or will be displayed: Lo HI

COMFORT INDICATION

The comfort indicaon feature is an icon-based system showing comfort level

based on indoor air temperature and humidity ranging from Excessive Cold (le

icon below) to Comfortable (center icon) to Excessive Heat (right icon).

Note: Comfort indicaon can vary even when measuring the same

temperature because of the strong eect humidity has on comfort. There is no

comfort indicaon when temperature is < 0°C (32°F) or > 60°C (140°F).

TEMPERATURE HUMIDITY TRENDING ARROWS AND

The temperature and humidity trend indicator illustrates the temperature and

humidity change over me. Arrows indicate rising (le icon shown below),

steady (center icon), falling temperatures (right icon). or

MAX/MIN RECORDING

View the MAX/MIN temperature and humidity readings since the last reset.

1. In normal mode, short pre to show the current maximum ss MIN-MAX

temperature and humidity values (diagram on le below); press again to

show the minimum values (diagram in center); press again to exit the mode

(the unit automacally exits the mode aer approximately 5 seconds).

2. Perform a manual reset (clear MAX/MIN readings) by long pressing MIN-

MAX when the unit is displaying the MAX/MIN records (diagram on right).

RECEIVING WIRELESS SENSOR SIGNALS

1. In normal mode, short press to start receiving data. SENSOR

2. The signal icon will ash (diagram on le below) unl recepon occurs .

Aer 5 minutes, the icon will disappear if recepon fails (center diagram).

3. Receiving wireless signal aer manual reset or when is pressed a a SENSOR

will cause dashes to display in the readings area when waing for signal.

4. For successful recepon, the signal icon will appear as shown in the

diagram below on right. The selected channel number appears in the box

below the icon.

1. In normal mode, short press to switch the display between INDOOR OUT

and CHANNEL 1~8.

2. In normal mode, long press to toggle auto-cycle mode ON/OFF. Auto-OUT

cycle alternately displays the channels at 4-second intervals (the icon will

show when auto-cycle is acve In auto-cycle mode only the acvely ).

communicang channels will appear. Short press to exit mode. OUT

3. To check the signals from mulple wireless sensors, short press OUT

repeatedly in normal mode.

4. If the signal for Channel 1~8 is lost and does not recover within 1 hour, the

signal icon will disappear. The temperature and humidity will display “Er”

for the corresponding channel.

5. If the signal does not recover within 48 hours, replace the baeries of the

“Er” el’s sens chann or and then press on the main unit to pair with SENSOR

the sensors for each “Er” channel again.

Note To iniate recepon aer installing new baeries in the wireless sensor,

press ; otherwise, the main unit will fail to receiv nal. SENSOR e the sensor’s sig

LOW TEMPERATURE ICON

When the outdoor temperature is 37.4°F (3.0°C) or below, the low temperature

icon ashes on the display. ‘ ’LO

LOW BATTERY CONDITION

If the main unit or the sensor baeries are low, the low baery icon will

display. The icon will only appear when the corresponding channel is displayed.

For example, if the sensor baery is low, the icon will show only CHANNEL 1

when 1 is displayed. Replace the baeries by following instrucons in CHANNEL

secons . Powering the Wireless Sensor and Powering the Main Unit

TEMPERATURE/HUMIDITY CALIBRATION

1. In normal mode, long press the key to enter the calibraon mode. T CAL he

current outdoor channel o icon will ash. Short press to r “IN” (indoor) OUT

choose Indoor (IN) or Channel number 1~8. a

2. Short press (MODE) to step through the temperature calibration, M

humidity calibraon, and channel selecon modes.

3. In temperature calibraon mode, use the [ ] [ ] keys to adjust the value + -

in 0.1° steps. Long press to scroll quickly.

4. In humidity calibraon mode, use the [ ] [ ] keys to adjust the displayed + -

value in 1% steps. Long press to scroll quickly.

5. Long press at the temperature or humidity calibraon screens to revert M

to the previous calibraon value for the selected channel.

6. To exit calibraon mode, long press or wait 60 seconds for the unit to CAL

exit and return to the normal mode automacally.

7. If the reading for the selected channel is showing either dashes (ashing) or

the / indicators, adjustment will not be possible; return unit for service. HI Lo

Note: Comfort indicaon is a calculaon based on calibrated temperature and

humidity measurements.

IMPORTANT NOTES

Aenon! Please dispose of baeries and unit in an ecologically safe manner.

Always place the unit away from interfering sources such as monitors,

computers, appliances, and other devices. Avoid placing the unit on, or next to,

metal plates or surfaces

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following

two condions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operaon.

Warning: Changes or modicaons to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protecon against harmful interference in a residenal installaon. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instrucons, may cause harmful interference to radio

communicaons.

However, there is no guarantee that interference will not occur in a parcular installaon.

If this equipment does cause harmful interference to radio or television recepon, which

can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separaon between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada License-exempt RSS-210. Operaon is subject to

the following two condions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operaon

of the device.

FCC Responsible party:

Company Name: FLIR Commercial Systems, Inc.

Address: 9 Townsend West, Nashua NH 03063 USA

Phone: 1- 603- -7842 324

IC ID: 1590A-RH200WT; FCC ID: IWK-RH200W-T; CAN RSS-Gen/CNR-Gen.

SPECIFICATIONS

MAIN UNIT

Indoor temperature range/resoluon: -5°C ~ 50°C (23°F ~ 122°F) / 0.1°C/°F

Temperature Accuracy: ±2°C (3.6°F), < 0°C (< 32°F)

±1°C (1.8°F), 0~40°C (32~104°F)

±2°C (3.6°F), > 40°C (> 104°F)

Humidity range/resoluon: 1% ~ 99 % / 1%

Humidity Accuracy (at 25°C [77°F]): ±8%RH (20~39% RH) ±5%RH (40~70% RH);

±8%RH (71~90% RH)

Power: 1.5V AA X 4 (alkaline baery recommended)

Dimensions: 130 (W) x 112 (H) x 27.5 (D) (5.1 x 4.4 x 1.1 in.) mm

Weight: 295g (0.65 lbs.)

WIRELESS SENSOR

Outdoor temperature range: -40°C ~ 60°C (-40°F ~140°F)

Outdoor humidity range 1% ~ 99 %

Temperature resoluon: 0.1°C/°F

Relave humidity resoluon: 1%

Accuracy: See accuracy specs for Main Unit above

Wireless sensor signal frequency: 433MHz

No. of remote sensors: Eight (8) units max.

RF transmission range 30m (98.4 .) maximum :

Power: 1.5V AA X 2 baeries (alkaline recommended)

Dimensions: 61 (W) x 113.6 (H) x 39.5 (D) mm (2.4 x 4.5 x 1.5 in.)

Weight: 136g (0.3 lbs.)

Produkt Specifikationer

Mærke:	Extech
Kategori:	Ikke kategoriseret
Model:	RH200W

Har du brug for hjælp?

Hvis du har brug for hjælp til Extech RH200W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Extech Manualer

20 August 2025

20 August 2025

22 Oktober 2024

27 September 2024

18 September 2024

13 September 2024

1 September 2024

1 September 2024

1 September 2024

28 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ulefone Armor X31 Pro Manual

27 September 2025

Advantech VEGA-3311 Manual

27 September 2025

Advantech PCM-24R2PE Manual

27 September 2025

Ensemble Designs BrightEye 16 Manual

27 September 2025

Ensemble Designs BrightEye 70 Manual

27 September 2025

Neets 306-0014 Manual

27 September 2025

Sanus BMF220 Manual

27 September 2025

Neets Touch Panel 10” Manual

27 September 2025

Advantech VEGA-320 Manual

27 September 2025

Sanus VisionMount LMT15 Manual

27 September 2025