Extron SMK P SM 26 Manual

Extron Højtalerbeslag SMK P SM 26

Læs gratis den danske manual til Extron SMK P SM 26 (4 sider) i kategorien Højtalerbeslag. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Extron SMK P SM 26, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Number of Wires

per Connection Point

Maximum

Wire Gauge

1 12 GAW

2 16 GAW

4 18 GAW

Wire Gauge Table

5.1"

(13.0 cm)

6.0"

5.2 )cm

2.6"

(6.6 cm)

3.5"

(8.9 cm)

R = 0.28"

(0.71 )cm

SMK P SM 26/28 Pivot Mount Kit • Setup Guide

This setup guide contains installation information about the Extron SMK P SM 26/28 Pivot Mount Kit.

WARNING: Installation and service must be performed by authorized personnel only.Potential risk of severe injury.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. L’installation et l’entretien doivent être effectués par

le personnel autorisé uniquement.

ATTENTION: The final installation should be able to continuously support the speaker weight. The final installation should

also be able to support any short term overloading. Since applications can vary considerably, it is assumed that the

installer will exercise good judgment when selecting the mounting location, method, and hardware. Installation and service

must be performed by authorized personnel only.

Installing the Pivot Mount Kit

The pivot mount enables the speaker to be positioned

and locked at various angles due to the adjustable ball

joint feature.

NOTE: Observe all applicable building codes and

local ordinances when installing the speaker.

ATTENTION: Attaching a secondary support

cable to the SM 26/28 speaker is required when

using the pivot mount kit.

1. Locate a suitable mounting location where the

pivot mount will be installed. Allow for the

dimensions of the SM 26 and SM 28, as shown

below.

SM 28 SM 26: :

2. All four mounting plate

screw holes must be secured

with at least two

screws attached to

a wall stud. Mark

the four holes on

the wall as indicated

by the wall plate

holes.

NOTE:

Mounting

hardware

is not

provided.

3. Drill the four holes

for the wall plate.

4. Drill a hole for the speaker wire.

5. Route the speaker wire through the speaker wire hole

while leaving enough slack for connection to the wall

plate.

NOTE: If the speaker wire is not being routed

through the wall, a notch on the wall plate allows

the wire to enter the wall plate from a raceway.

6. Attach speaker wires to the Euroblock on the wall plate.

Quick Connect Contacts

11.50"

(29.21 cm)

2.44 - 3.35"

(6.20 - cm 8.51)

7.28"

(18.50 cm)

16.50"

1.91 )cm

9.2"

(23.37 )cm

8.45"

(21.46 cm)

2.44 - 3.35"

(6.20 - cm 8.51)

6.45"

(16.38 cm)

12.98"

(32.97 )cm

9.16"

(23.27 cm)

Produkt Specifikationer

Mærke:	Extron
Kategori:	Højtalerbeslag
Model:	SMK P SM 26

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron SMK P SM 26 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højtalerbeslag Extron Manualer

Extron SMK P SM 26 Manual

10 Juli 2025

Extron SMK V SB 33 Plus Manual

6 Juli 2025

Extron V-Lock Manual

6 September 2024

Højtalerbeslag Manualer

Nyeste Højtalerbeslag Manualer

Echogear EGAV-SSBWM1 Manual

3 November 2025

WALI OSH001 Manual

3 November 2025

OmniMount ELO Manual

3 November 2025

Mounting Dream MD5428 Manual

2 November 2025

ErgoAV ERSB2-01B Manual

31 Oktober 2025

Outdoor Tech OT3800 Manual

30 Oktober 2025

Kanto SX26W Manual

25 Oktober 2025

Valcom VB-R17-D Manual

14 Oktober 2025

Triangle S01 Manual

6 Oktober 2025

APart MASK2CMT-W Manual

6 Oktober 2025