Extron SW HD 4K PLUS Series Manual

Extron Skifte SW HD 4K PLUS Series

Læs gratis den danske manual til Extron SW HD 4K PLUS Series (4 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Extron SW HD 4K PLUS Series, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

SW6 and SW8 HD 4K PLUS • Setup Guide

The Extron SW HD 4K PLUS are six and eight input HDMI switchers that support 4K video signals at 60 Hz. They

switch 4K/60 signals between multiple HDMI source devices to a single display. The switchers support computer and

video resolutions up to 4K/60 and 1080p/60, data rates up to 18 Gbps, HDR, 12-bit Deep Color, 3D, Lip Sync, and

HD lossless audio formats. Both models feature EDID Minder

®, which maintains continuous EDID communication

with connected devices and ensures that the HDMI sources power up properly and maintain correct video output.

The switchers also provide automatic input cable equalization up to 25 feet (7.6 meters) when used with Extron

HDMI Pro Series cable.

The SW HD 4K PLUS Series offers control via front panel buttons, USB, Extron Product Control Software (PCS),

Ethernet, RS-232, contact closure, and auto-input switching for integration with any control system. Front panel LED

indicators provide immediate conrmation of HDCP authentication and signal presence for each input and output.

This guide provides instructions for an experienced installer to set up and operate these switchers.

For full

installation, conguration, and operation details, see the , available at SW HD 4K PLUS Series User Guide

www.extron.com.

Rear Panel Features and Connections

SW6 HD 4K PLUS

Tx Rx G

GC T GC

C T TGC G

C T

T GC T

RS-232

CONT ACT IN/TALLY OUT

INPUTS

1 2 3 4 5 6

100-240V 0.2A MAX

50/60 Hz

OUTPUT

REMOTE

LAN

RESET

SW8 HD 4K PLUS

Tx Rx G

GC T GC

C T TGC G

6 8

C T TGC

T GC T GC

5 7

T +V

RS-232

CONT ACT IN/TALLY OUT

INPUTS

1 2 3 4 567

100-240V 0.2A MAX

50/60 Hz

OUTPUT

REMOTE

LAN

RESET

HE F

A Power connector E RS-232 connector

B HDMI Input connectors F LAN (Ethernet) connector

C HDMI Output connector G Contact closure input and tally output ports

D +V connector (for tally voltage output) H Reset button

Figure 1. SW6 and SW8 HD 4K PLUS Rear Panel

Installation Steps

1. Turn off all of the equipment and disconnect it from the power source.

2. Mount the switcher on a rack shelf or furniture (optional). (See the instructions provided with the mounting kit,

which can be ordered at www.extron.com).

3. Connect HDMI input sources to one or more of the SW HD 4K PLUS input connectors (see gure 1,

B).

NOTE: LockIt® cable lacing brackets, one for each HDMI input and output connector, are provided with the

SW HD 4K PLUS. These brackets can be used to secure the HDMI cables to the rear panel connectors

to reduce stress on the HDMI connectors and prevent signal loss due to loose cable connections. For

information on attaching the LockIt brackets, see the LockIt HDMI Lacing Bracket instructions in the

SW HD 4K PLUS Series User Guide, available at www.extron.com.

SW6 and SW8 HD 4K PLUS • Setup Guide (Continued)

4. Connect an HDMI output device to the output connector (see ﬁgure 1,

C, on the previous page . By default, )

the EDID of this device is stored at the HDMI output.

5. Connect control devices. Connect your computer

to one of the following SW HD 4K PLUS

communication ports to congure and control the

switcher via SIS commands or via PCS (Cong and

LAN ports only):

• RS-232 port — Connect the unterminated

transmit, receive, and ground wires of the RS-232

cable to the provided 3-pole captive screw plug, as

shown in the illustration at right. Connect the plug

between the rear panel RS-232 connector (

E), and

the serial port of your computer. Protocol for the

RS-232 port is 9600 baud, 8 data bits, 1 stop bit,

no parity.

• Config port — Connect a USB mini-B cable between the front panel USB mini-B connector (see ﬁgure 2,

B, on page 3) and a USB port on your computer for control via USB.

• LAN port — Use an RJ-45 cable to connect this jack (see figure 1,

F) to a LAN for Ethernet control of the

switcher.

6. (Optional) Connect contact closure and indicator devices. The panel on the SW6 and SW8

models contains six (SW6) or eight (SW8) 3-pole captive screw connectors, each with three pins labeled , ,

and , for contact closure and tally indicator devices. The panel also contains a 3-pole captive screw connector

with three +V pins that provide power to the indicator devices connected to the tally ( ) ports (see

2 in the

illustration below right).

Each 3-pole connector is labeled with the number of the HDMI input associated with it. Wire devices to these

connectors as follows:

a. Connect contact input and tally output devices to one or

more of the 3-pole CONTACT IN/TALLY OUT connectors

(see 1 in the illustration at right), as desired:

• To enable input switching via contact closure, connect

a push-button contact closure input device to pins

(contact) and (ground).

• To identify the currently selected input when the front

panel buttons are not visible, connect an indicator

device, such as an LED, to tally output pin of the

same 3-pole connector.

When the input you are using is selected, the

corresponding tally out pin shorts to ground, which activates the connected indicator.

b. If desired, attach the power wires for your connected indicator devices to any of the three ports of the

connector (2).

NOTE: You need to connect the indicator LED to the voltage output if you want to power the device for

visual feedback. However, only the contact and ground connections are needed to select an input.

Pressing the button on the contact closure device switches the connected input to the output.

Computer or

Control Syste

RS-232 Port

SW HD 4K Series Switcher

Rear Panel

Remote Port

NOTE: If you use cable that has a drain

wire, tie the drain wi to ground at both ends.re

Ground (G)

Transmit (Tx)

Receive (Rx) Transmit (Tx)

Receive (Rx)

Tx Rx G

RS-232

Tx Rx G

GC T GC

C T TGC G

6 8

C T TGC

T GC T GC

5 7

T +V

RS-232

CONTACT IN/TALLY OUT

REMOTE

1 2

Produkt Specifikationer

Mærke:	Extron
Kategori:	Skifte
Model:	SW HD 4K PLUS Series

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron SW HD 4K PLUS Series stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Extron Manualer

Extron SW HD 4K Series Manual

7 September 2024

Extron SW HD 4K PLUS Series Manual

6 September 2024

Extron 60-1472-12 Manual

5 September 2024

Extron eLink 100 T EU Manual

5 September 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025