Fe Powertools L Manual

Fe Powertools bore L

Læs gratis den danske manual til Fe Powertools L (6 sider) i kategorien bore. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Fe Powertools L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

2 Manual magnetic drilling machines

1. Table of contents

2. Table of contents

3. Safety procedures

4. Technical overview

5. Operating manual

5.1 Hole cutter selection

5.2 How to mount tools or adapters in a Weldon arbor

5.3 Drilling with hole cutters

5.4 Drilling with twist drills

5.5 Tapping / threading

5.6 Speed and torque setting

6. Tips and tricks

7. Maintenance

8. CE Declaration of Conformity

9. Warranty

3 Manual magnetic drilling machines

1. Safety procedures

When using magnetic drilling machines please follow the general safety instructions for electric

power tools.

Please read the manual Use eye protection use ear protection

use safety helmet use safety gloves wear appropriate clothing

disconnect before opening use safety chain Warning for electrical shock

dangerous environment don’t use in wet places pacemaker warning

TIP: Do not use your magnetic drill on the same structure when ARC welding is in progress. D.C.

current will earth back through the magnet and cause irreparable damage.

WARNING: This appliance must be earthed.

1. Always secure the machine with the supplied safety chain before starting to operate, this to protect the user in case of power

failure or breaking loose of the magnet whilst in use.

2. Always wear safety goggles, gloves and ear plugs.

3. Disconnect from the power source when changing cutters or working on the machine.

4. Always ensure cutter retaining screws are secure – they sometimes vibrate loose in use.

5. Regularly clean the work area and machine., remove swarf and dirt, paying particular attention to the underside of the magnet.

6. With a gloved hand, after switching off the power, remove any swarf which might have gathered around the cutter and arbor

before proceeding to the next hole.

7. Remove tie, rings, watches and any loose adornments which might entangle with the rotating parts of the machine.

8. Should the cutter get stuck in the workpiece, stop the motor immediately to prevent personal injury. Disconnect from the

power source and push and pull the arbor by hand. DO NOT ATTEMPT TO FREE THE CUTTER BY SWITCHING THE MOTOR ON

AND OFF.

9. If the machine is accidentally dropped, always thoroughly examine the machine for signs of damage and check that it functions

correctly before trying to drill a hole.

10. Regularly inspect the machine and check the nuts and screws are tight.

11. Always ensure when using the machine in an inverted position that only the minimum amount of coolant is used and that care

is taken to ensure the coolant does not drip in the motor unit. We advise you to use special cutting paste which is specially

designed for inverted position drilling.

12. ONLY use spare parts advised by your dealer for magnetic drilling machines.

13. Use the magnetic drilling unit on a clean and flat surface only, to prevent the machine breaking out because of poor clamping

force.

14. If you discover any irregularity on machine cables immediately bring the machine to a recognized dealer for a repair or

maintenance service.

4 Manual magnetic drilling machines

2. Technical overview

FE 30 FE 32 FE 32 R/L FE 36 S FE 50 FE 50 R/L FE 100 R/L

Motor

800 W 900 W 1050 W 1080 W 1150 W 1150 W 1800 W

Spindle Direct – 19

mm Weldon

½”x20 NF

– 19 mm

Weldon

½”x20 NF –

19 mm

Weldon

Direct – 19

mm Weldon

MT 2 – 19

mm Weldon

MT 2 – 19 mm

Weldon

MT 3 – 19 mm

Weldon

Hole cutter

30 mm

30 mm 32 mm 32 mm 36 mm 50 mm 50 mm 100 mm

Hole cutter

55 mm

30 mm 32 mm 32 mm N/A 50 mm 50 mm 100 mm

Hole cutter

110 mm

N/A N/A N/A N/A 50 mm 50 mm 100 mm

Countersink

N/A N/A 30 mm N/A N/A 40 mm 55 mm

Reaming

N/A N/A N/A N/A N/A 23 mm 31.75 mm

Twist drills

N/A 13 mm 13 mm N/A 23 mm 23 mm 31.75 mm

Tap

N/A N/A M 16 N/A N/A M 20 M 30

RPM

450 min‐1 450 min‐1 0‐350 min‐1 400 min‐1 I 250 min‐1

II 450 min‐1

I 50‐250 min‐1

II 100‐450 min‐1

I 40‐140 min‐1

II 120‐480 min‐1

Stroke

80 mm 150 mm 150 mm 39 mm 150 mm 150 mm 250 mm

Weight

9.9 kg 12 kg 12 kg 11 kg 13 kg 13 kg 27 kg

Magnet

1500 kg 1500 kg 1500 kg 1200 kg 1700 kg 1700 kg 3500 kg

Check power supply

Make sure the used current corresponds with the machine specifications. When using a cable

extension make sure it can do the job.

Produkt Specifikationer

Mærke:	Fe Powertools
Kategori:	bore
Model:	L

Har du brug for hjælp?

Hvis du har brug for hjælp til Fe Powertools L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bore Fe Powertools Manualer

Fe Powertools FE 30 kernboormachine Manual

8 August 2024

Fe Powertools L Manual

31 Juli 2024

bore Manualer

Nyeste bore Manualer

Einhell BM-G1100 E Manual

14 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Manual

14 Oktober 2024

DeWalt DWD450 Manual

14 Oktober 2024

Rupes BH 252R Manual

13 Oktober 2024

Makita DHR263ZJ Manual

12 Oktober 2024

Makita HP2070 Manual

12 Oktober 2024

Makita DDA350RFJ Manual

7 Oktober 2024

Einhell TE-ID 750/1 E Manual

7 Oktober 2024

Makita HP332D Manual

7 Oktober 2024

Makita M6501 Manual

6 Oktober 2024