Festo CRDSNU-100 Manual

Festo Ikke kategoriseret CRDSNU-100

Læs gratis den danske manual til Festo CRDSNU-100 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Festo CRDSNU-100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product www.festo.com/sp.è
2 Safety
2.1 Safety Instructions
– Take into consideration the ambient conditions at the location of use.
– Only use the product in original status without unauthorised modifications.
– Store the product in a cool, dry, UV-protected and corrosion-protected envir-
onment. Ensure that storage times are kept to a minimum.
– Prior to mounting, installation and maintenance work: Switch off compressed
air supply and secure it from being switched back on.
– Observe tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2 Intended use
The product is intended for the transport of loads.
2.3 Training of skilled personnel
Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel.
3 Further information
– Accessories www.festo.com/catalogue.è
– Spare parts www.festo.com/spareparts.è
4 Service
Contact your regional Festo contact person if you have technical questions
èwww.festo.com.
5 Product overview
5.1 Function
The piston rod moves outwards when the cylinder chamber is pressurised. The
advanced piston rod is retracted as follows:
– For double-acting cylinders, by pressurising the other cylinder chamber.
The cylinder force during advance and return is:
– different with piston rod at one end.
The position of the piston can be detected by proximity switches.
5.2 Design
1
Male thread on the piston rod for
mounting the payload
2
Male thread on the bearing cap for
mounting
3
Supply ports in the bearing/end
cap
4
Cross hole for mounting
Fig. 1 Sample illustration CRDSNU
5.3 Mounting
• Handle the cylinder so as to avoid any damage to the cylinder barrel and pis-
ton rod.
• Observe the following points:
– parallel mounting when using external guides
– installation without distortion
– Compliance with the permissible loads www.festo.com/catalogueè
• Observe tightening torque of lock nuts on the male thread .2
Size 12 16 20 25 32 40 50 63 80 100
Tightening torque
on the bearing cap
[Nm] 15 15 40 40 60 80 100 100 550 550
Tab. 1 Tightening torques on the bearing cap
• Avoid mechanical alignment inaccuracies between the piston rod and an
external guide using one of the following measures:
– absolutely precise alignment (general)
– use of a self-aligning rod coupler FK
– use of a guide unit FEN with compensating coupling
A rigid coupling impairs the service life and function of the cylinder.
5.4 Mounting Accessories
In the case of a large payload, high piston speed or when using quick exhaust
valves:
• Use suitable shock absorbers or external stops.
To prevent the payload from sliding down suddenly in the event of an air supply
failure in a horizontal or sloping mounting position:
• Use piloted check valves.
To set the speed:
• Use one-way flow control valves in the following supply ports:
– For single-acting cylinders: GRLZ (supply air)
– For double-acting cylinders: GRLA (exhaust air)
The one-way flow control valves are screwed directly into the supply ports. Use of
other accessories with a screw-in depth that is too long will damage the cushion-
ing piston.
For position sensing with proximity sensors:
• Use proximity sensors with mounting kit.
Avoid external influence caused by magnetic or ferritic parts in the vicinity of
the proximity sensors (spacing 10mm).³
6 Installation
6.1 Pneumatic Installation
• Connect tubing to supply ports.
7 Commissioning
7.1 Preparation
• Pressurise the system slowly. A soft start valve is used for gradual start-up
pressurisation www.festo.com/catalogue. è
With medium or large payloads or at high speeds:
• Use sufficiently large arrester fixtures. The product will tolerate the maximum
velocities and payloads without external arrester fixtures
èwww.festo.com/catalogue
8143197
CRDSNU
Round cylinder
8143197
2021-01c
[8143199]
Operating instructions
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com

Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: CRDSNU-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo CRDSNU-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Festo Manualer

Festo

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025
Festo

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025
Festo

Festo VABD-S2-1-S-C Manual

20 August 2025
Festo

Festo SIED-M18B-ZO-S-L Manual

19 August 2025
Festo

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025
Festo

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-CO-DE Manual

19 August 2025
Festo

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025
Festo

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM E43416 Manual

2 Januar 2026
Pyle

Pyle PCRMP2DY Manual

2 Januar 2026
Testboy

Testboy TV 285 Manual

2 Januar 2026
Pioneer

Pioneer 2AM700 Manual

2 Januar 2026
Ruvati

Ruvati RVH7419 Manual

2 Januar 2026
Vaxcel

Vaxcel T0703 Manual

2 Januar 2026
Govee

Govee H1167 Manual

2 Januar 2026
Ruvati

Ruvati RVH9733 Manual

2 Januar 2026
Sonnenkönig

Sonnenkönig Slim E 1000 Manual

2 Januar 2026
Asus

Asus Prime AP202 Manual

2 Januar 2026