Festo DADG-D-F8-16/20 Manual

Festo Ikke kategoriseret DADG-D-F8-16/20

Læs gratis den danske manual til Festo DADG-D-F8-16/20 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Festo DADG-D-F8-16/20, eller vil du spørge andre brugere om produktet?

Side 1/1
Translation of the original instructions
1 Applicable documents
All available documents for the product www.festo.com/pk.è
Document Product Contents
Instructions Holding brake DACS-...-S
Cylinder with holding brake DFLC/DFLG-...-S
Operating
Instruction manual from the
original manufacturer
Proximity sensor Contrinex DW-AD-603-M4 Installation
Tab. 1 Applicable documents
2 Safety
2.1 Safety instructions
Only assemble the product on components that are in a condition to be safely
operated.
Observe tightening torques. Unless otherwise specified, the tolerance
is±20%.
2.2 Intended use
Status monitoring of holding brakes DACS, DFLC und DFLG.
2.3 Foreseeable misuse
The inductive proximity sensor DADG-D-F8 is exclusively provided for status mon-
itoring and is not suitable as a safety-relevant test system.
3 Further information
Accessories www.festo.com/catalogue.è
Spare parts www.festo.com/spareparts.è
4 Product overview
4.1 Product range overview
4.1.1 Scope of delivery
1Proximity sensor (1x)
Fig. 1
4.1.2 Not in scope of delivery
2Holding brake (1x)
DACS-...-S,
Cylinder with holding brake
DFLC/DFLG-...-S
Fig. 2
4.2 Function
Holding brake status Signal status
Closed On
Open Off
Tab. 2 Status monitoring
5 Assembly
Fig. 3 Remove threaded pin
1. Depressurise holding brake .2
2. Unscrew the threaded pin[A] from the outer surface.
Fig. 4 Screw in the proximity sensor
1. Screw the proximity sensor into the thread[C] up to the stop. Use the1
hexagon(D) on the sensor.
ÄThe lock nut[B] does not rest on the outer surface.
2. Connect the proximity sensor .1
ÄThe signal lights up.
Fig. 5 Adjust proximity sensor
Unscrew the proximity sensor slowly until the signal goes out.1
Fig. 6 Adjust proximity sensor
Screw the proximity sensor in slowly until the signal lights up.1
Fig. 7 Lock the proximity sensor
Tighten the lock nut[B]. Tightening torque:4Nm
6 Technical data
DADG-D-F8
Mounting type Flush
Ambient temperature [°C] –25 ... 70+
Switching frequency f [Hz] 5000
Degree of protection IP67
Housing material Steel, phosphated
Cable material TPE-U (PUR)
Voltage drop Ud [V] £ 2
Tab. 3 Technical data
8107310
DADG-D-F8
Proximity sensor
Instructions | Assembly
8107310
2019-06
[8107312]
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DADG-D-F8-16/20

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DADG-D-F8-16/20 stil et spørgsmål nedenfor, og andre brugere vil svare dig