Festo DADM-TK-220 Manual

Festo Ikke kategoriseret DADM-TK-220

Læs gratis den danske manual til Festo DADM-TK-220 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Festo DADM-TK-220, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Assembly instructions (Original instructions)

8072099

2017-05d

[8072101]

†‡

Reciprocating motion kit

DADM-TK

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

1. Applicable documents

All available documents for this product  www.f

esto.com/pk

 Operating instructions for rotary indexing table 5

2. Safety

Observe the safe

ty information ( Applicable documents).

Comply with tightening torques ( Table).

3. I

ntended use

Recip

rocating motion kit DADM-TK:

Conversion of the rotary indexing table DHTG to reciprocating motion.

4. Scope of delivery

11377d_1

1 Shock absorber

2 Stop pin with O-ring

3 Retaining ring

DIN 472

4 Flat seal

(1x)

(4x)

(1x)

(4x)

5. Not in scope of d

livery

1137

7d_12

5 Rotary indexing

table DHTG

(B) Stop plate

(H)

Shock absorber

plate

(1x)

6. Screw sizes and tightening torques M

DADM-TK 65 90 140 220

2 Stop pin M4

[Nm] 1.5

(A) Screw M5x16 (3x) M5x16 (5x) M6x16 (5x) M6x20 (5x)

[Nm] 2.9 5.9

(F) Flow control

valve

GRLA-M5-B GRLA-1/8-QS-8-D

[Nm] 1.5 5.5

(G) Screw M4x16 (4x) M4x16 (5x) M6x16 (6x) M6x25 (6x)

[Nm] 2.9 9.9

Tolerance for tightening torques M

without indication of tolerance ± 20 %

7. Preparations for mounting

Unlock rotary indexing table 5 ( Applicable documents).

To unlock:

Pressurize the supply port A with at least 4 bar.

 The rotary table can be turned freely.

Switch off compressed air.

Exhausting the rotary indexing table.

8. Mounting

Unscrew screws (A).

Remove stop plate (B).

11377d_13

Check stop plate (B).

The stop plate (B) contains

drill holes (E) or threads (E).

– For drill holes (E)

 Section 8a.

– For threads (E)

 Section 8b.

8a. For drill h

les (E)

11377d_25

Remove O-rings (C) from

the drill holes (D).

1137

7d_26

Place two seals 4 on

the drill holes (D).

11377d_9

Fasten the stop plate (B)

using the screws (A).

11377d_2

Unscrew flow control

valve (F).

Unscrew screws (G).

Remove shock absorber

plate (H).

11377d_3

Remove O-rings (J) from

the drill holes (K).

11377d_4

Place two seals 4 on

the drill holes (K).

Turn the rotary table.

 Left drive piston (L) comes

forward

)

Push the shock absorber 1

into the drive piston (L).

Fasten the shock

absorber 1 with the

retaining ring 3.

Check remaining O-rings

for correct fit.

11377d_5

Fasten shock absorber

plate (H)

with the

screws (G).

Screw throttle valve (F)

in tightly.

11377d_10

Remove the plugs (M)

and (N).

Information

Four stop pins 2 and four O-rings (J) are left over.

8b. For threads (E)

11377d_24

Tighten two stop pins 2

in the threads (E) of the

stop plate (B).

11377d_27

Fasten the stop plate (B)

using the screws (A).

11377d_2

Unscrew flow control

valve (F).

Unscrew screws (G).

Remove shock absorber

plate (H).

11377d_21

Tighten two stop pins 2

in the threads (O) of the

shock absorber plate (H).

11377d_22

Turn the rotary table.

 Left drive piston (L)

comes forward

)

Push the shock absorber 1

into the drive piston (L).

Fasten the shock

absorber 1 with the

retaining ring 3.

Check all O-rings for

correct fit.

11377d_23

Fasten shock absorber

plate (H)

)

with the

screws (G).

Screw throttle valve (F)

in tightly.

11377d_10

Remove the plugs (M)

and (N).

Information

Four seals 4 are left over.

2) 3)

9. After mounting

During reciprocating motion, locking is separated from rotation.

Always actuate turn (right/left) and unlock/lock with a controller

accordingly ( Applicable documents).

In case of division > 2 (BG65 and 90)/ > 3 (BG140 and 220):

There is a spacing bolt in front of the left drive piston (L). Remove the spacer bolt during

dismantling and insert it again during mounting.

For division > 2:

When attaching the shock absorber plate, place the small compression spring back into

the drill hole (X) so that it presses on the spacer bolt.

)

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	DADM-TK-220

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DADM-TK-220 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW PROPULLATOR 2500MH Manual

3 November 2025

ANCEL HD3200 Manual

3 November 2025

Lantronix C3220 Manual

3 November 2025

Cooler Master MasterBox MB511 Manual

3 November 2025

Klarstein La Palma 750 Smart Manual

3 November 2025

ANCEL AD610 Elite Manual

3 November 2025

ErgoAV ERIWA1-01W Manual

3 November 2025

QOLIXm YQAWSL-6A4U Manual

3 November 2025

ANCEL AJ400 Manual

3 November 2025

Emerson ITL9907RE Manual

3 November 2025