Festo DADP-DGC-18-KF Manual

Festo Ikke kategoriseret DADP-DGC-18-KF

Læs gratis den danske manual til Festo DADP-DGC-18-KF (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Festo DADP-DGC-18-KF, eller vil du spørge andre brugere om produktet?

Side 1/2
3.
DADP-DGC
Shock absorber retainer
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Assembly instructions
8174040
2022-11c
[8174042]
8174040
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
èwww.festo.com/sp.
Document Product Table of contents
Operating instruction Linear drive DGC(I)
Assembly instructions Stop KYC
Operating instruction Intermediate-position module
DADM-DGC-25...40
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Only use the product in its original condition without unauthorised modifica-
tions.
Observe the tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2 Intended use
The shock absorber retainer fastens shock absorbersYSR(W)-DGC to the slide of
linear drivesDGC-...-GF/-KF/-FA or DGCI. Use the shock absorber retainer only in
combination with a counter part for the cushioning:
Stop KYC
Intermediate-position module DADM-DGC
3 Additional information
Contact the regional Festo contact if you have technical problems
èwww.festo.com.
Accessories èwww.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
2
3
4
Fig.1
1
Shock absorber retainer (1x)
2
Centring sleeve (2x)
3
Screw (2x),
only with DADP-DGC-…-KF
4
Screw (2x)
4.2 Not in scope of delivery
5
Fig.2
5
Linear drive (1x)
DGC-...-GF
DGC-...-KF,
DGC-...-FA,
DGCI
6
Fig.3
6
Stop (1x/2x)
KYC
7
Fig.4
7
Shock absorber (1x/2x)
YSR(W)-DGC
8
Fig.5
8
Intermediate-position module
DADM-DGC
5 Assembly
5.1 Preparation for DADP-DGC-18…-40
ZW X YV
Fig.6
Check the slide of the linear drive .5
Steel slide:
Multi-piece slide[V]
Screws[W], spring pins[X] and plastic cover[Y]
Aluminium slide:
One-piece slide[Z]
5.2 Mounting shock absorber retainer
2
A
1
3
V
Fig. 7: Mounting on steel slide
2
A
1
4
Z
Fig. 8: Mounting on aluminium slide
1. Place the centring sleeves in the seats[A].2
2. Place the shock absorber holder on the centring sleeves .1 2
Select the appropriate screws / :3 4
shorter screws for multi-piece steel slide[V].3
longer screws for one-piece aluminium slide[Z].4
Two screws are left over with DADP-DGC-…-KF.
4. Tighten the screws / . Observe the tightening torque.3 4
DADP-DGC -18-GF -25-GF -32-GF -18-KF -25-KF -32-KF
Screw M5 x 303
Screw M5 x 30 M5 x 354
[Nm] 4 6
DADP-DGC -40-GF -40-KF -50 -63
Screw M6 x 35 3
Screw M6 x 35 M6 x 45 M8 x 454
[Nm] 8 10 25
5.3 Mounting shock absorber
If available, shock absorbers from the end cap of the linear drive can be used.5
7
B
Fig.9
Depending on requirements screw one or two shock absorbers with stop7
sleeve and lock nut completely into the shock absorber retainer . Observe1
the tightening torque of the lock nut.
YSR(W)-DGC -18-GF -25-GF -32-GF -18-KF -25-KF -32-KF
[Nm] 3 5 8 5 20 20
YSR(W)-DGC -40-GF -40/50-B -63
[Nm] 20 35 30
5.4 Mounting stop elements
1. Mount one or two stops depending on requirements 6è1 Applicable
documents.
2. Mount intermediate-position modules depending on requirements 8è1
Applicable documents.


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DADP-DGC-18-KF

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DADP-DGC-18-KF stil et spørgsmål nedenfor, og andre brugere vil svare dig