Festo DAMH-L8-40-PL-1 Manual

Festo Ikke kategoriseret DAMH-L8-40-PL-1

Læs gratis den danske manual til Festo DAMH-L8-40-PL-1 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Festo DAMH-L8-40-PL-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Assembly instructions (Original instructions)

8070340

2017-07

[8070342]

†‡

Profile mounting

DAMH-L8-...-PL-1

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

1. Further applicable documents

All available documents for the product  www.f

esto.com/pk

 Operating instructions of the linear actuator 7

2. Safety

Switch off power supply and compressed air before mounting work.

Observe further applicable documents.

Comply with tightening torques ( Table).

3. Intended use

Fastening of two linear actuators 7 to a mounting surface.

4. Scope of delivery

18446d_1

1 Profile mounting

2 Sleeve

3 Screw

4 Screw

5 Knurled nut

6 Nut

(2x)

(1x)

5. Not in scope of delivery

18446d_2

7 Linear actuator

DLGF

8 Screw

(2x)

(4x)

6. Mounting

Determine the mounting points ( Further applicable documents).

18446d_3

Position actuators 7

flush with each other.

Place a knurled nut 5

into the drill hole (A) of

a determined fastening

point.

Lightly clamp the

actuators 7 into place

with the screw 4 and

knurled nut 5.

Place the sleeves 2

into the drill holes of the

profile mountings 1.

Push the screw 3 through

the sleeves 2, profile

mountings 1 and drill

holes (B) as shown.

18446d_4

Clamp the profile

mountings 1 to the

actuator 7 using the

hex nut 6.

Align the profile

mounting 1 parallel

to the actuators 7.

Tighten the hex nut 6.

Tighten the screw 4.

Repeat the mounting steps

for all mounting points.

18446d_5

Attach the profile

mountings 1 to the

mounting surface using

2 screws 8.

7. Screw sizes and tightening torques M

Information

Select screws 8 suitable for the installation situation.

DAMH-L8-...-PL-1 20 25 32 40

3 Screw M4x60 M5x70 M6x90 M6x110

[Nm] 2.2 5.0 8.5 9.0

4 Screw M4x35 M5x45 M6x55 M6x70

[Nm] 2.2 5.0 8.5 9.0

6 Nut M4 M5 M6 M6

[Nm] 2.2 5.0 8.5 9.0

8 Screw M4 M5 M6 M6

Tolerances for tightening torques M

without indication of tolerance

. 3 Nm: ± 10 %

, 3 Nm: ± 20 %

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	DAMH-L8-40-PL-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DAMH-L8-40-PL-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025