Festo DFPC-320 Manual

Festo Ikke kategoriseret DFPC-320

Læs gratis den danske manual til Festo DFPC-320 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Festo DFPC-320, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DFPC

Linear drive

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Operating instructions

8165883

2021-10b

[8165885]

Translation of the original instructions

Applicable Documents

All available documents for the product

www.festo.com/sp.

2 Safety

2.1 Safety instructions

–

Take into account the ambient conditions at the location of use.

–Only use the product in its original condition without unauthorised modifica-

tions.

–

Observe the identifications on the product.

–Before switching off the compressed air supply: secure the load on the piston

rod.

–Prior to assembly, installation and maintenance work: switch off the com-

pressed air supply and secure it against being switched back on.

–

Keep the travel path of the piston rod clear.

2.2

Intended use

The intended use of the product is to implement linear movements in a com-

pressed air machine in an industrial environment.

2.3 Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can

evaluate the work and detect dangers. The qualified personnel have skills and

experience in dealing with pneumatic (open-loop) control technology.

Additional information

Contact the regional Festo contact if you have technical problems

www.festo.com.

4 Product design

Fig. 1:

Product design

Pneumatic port 2

Cylinder barrel

Extended tie rod

(only for DFPC-...-LB2)

Piston rod

Pneumatic port 1

Bearing cap

End cap

5 Function

Pressurising and exhausting the cylinder chambers causes the piston rod con-

nected to the piston to move back and forth.

Fig. 2:

Function

Transport and storage

Store the product in a cool, dry environment protected from UV and corrosion.

Keep storage times short.

Do not use the tie rods as a transport aid.

Assembly

• Fasten the linear drive to one of the mounting interfaces.

Potential mounting interfaces:

–Mounting thread on the bearing cap

–Extended tie rods (only for DFPC-...-LB2)

8 Pneumatic Installation

1. Remove the plugs at the pneumatic connections.

2. To set the travel speed, use one-way flow control valves.

3. Screw the fittings into the pneumatic connections 1 and 2.

Commissioning

Requirements

–

The linear drive is fully mounted and connected.

–The permissible impact energy at the end stop must not be exceeded

Technical data.

–The piston rod or the piston rod bearing must not be subjected to transverse

loads. The dead weight of the piston rod must be absorbed.

–

Take the permissible buckling load into account

14.1 Permissible buckling load.

Permissible impact energy at end stop

The permissible impact energy at the end stop is dependent on the impact

velocity and the mass of the moving payload.

Impact velocity and mass of the moving payload

Permissible impact velocity

Permissible mass of the moving payload

perm

Max. impact energy

Intrinsic

Moving mass (drive)

14 Technical data

Intrinsic

= moving mass with 0 mm stroke + added moving mass per 10 mm stroke

Load

Permissible mass of the moving payload

v Operating velocity

perm

Permissible impact velocity

Tab. 1: Impact velocity and mass of the moving payload

Commissioning the linear drive

Pressurise the product slowly. A soft start valve is used for the gradual start-

up pressurisation .

Screw the one-way flow control valves all the way in on both sides, then

loosen by one turn.

Exhaust the cylinder on one side.

The piston rod moves to an end position.

Start a test run.

During the test run, check the velocity of the moving mass and the end stop.

10 Operation

WARNING

Risk of injury due to unexpected movement of components.

Body parts in the movement range of the piston rod can be crushed or severed.

• Protect the positioning range from unwanted intervention.

•

Keep foreign objects out of the positioning range.

•

Observe the operating conditions.

• Observe the permissible limit values.

Maintenance

If used as intended, the product is maintenance-free.

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	DFPC-320

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DFPC-320 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM E43416 Manual

2 Januar 2026

Pyle PCRMP2DY Manual

2 Januar 2026

Testboy TV 285 Manual

2 Januar 2026

Pioneer 2AM700 Manual

2 Januar 2026

Ruvati RVH7419 Manual

2 Januar 2026

Vaxcel T0703 Manual

2 Januar 2026

Govee H1167 Manual

2 Januar 2026

Ruvati RVH9733 Manual

2 Januar 2026

Sonnenkönig Slim E 1000 Manual

2 Januar 2026

Asus Prime AP202 Manual

2 Januar 2026