Festo DHPC-L-16-A-B-2 Manual

Festo Ikke kategoriseret DHPC-L-16-A-B-2

Læs gratis den danske manual til Festo DHPC-L-16-A-B-2 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Festo DHPC-L-16-A-B-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

DHPC

Parallel gripper

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Operating instructions

8150807

2021-05a

[8150809]

Translation of the original instructions

Applicable Documents

All available documents for the product

www.festo.com/sp.

2 Safety

2.1 Safety Instructions

–

Take into consideration the ambient conditions at the location of use.

–Only use the product in original status without unauthorised modifications.

–Observe labelling on the product.

–

Store the product in a cool, dry, UV-protected and corrosion-protected environ-

ment. Ensure that storage times are kept to a minimum.

–

Prior to mounting, installation and maintenance work: Switch off compressed

air supply and secure it from being switched back on.

–Observe tightening torques. Unless otherwise specified, the tolerance is

± 20 %.

2.2 Intended use

The intended use of the product is to grip and hold payloads (workpieces) using

custom-designed gripper fingers attached by the customer.

2.3 Training of qualified personnel

Installation, commissioning, maintenance and disassembly should only be con-

ducted by qualified personnel.

The specialized personnel must be familiar with the installation and operation of

electrical and pneumatic control systems.

3 Additional information

–Contact the regional Festo contact if you have technical problems

www.festo.com.

–Accessories and spare parts

www.festo.com/catalogue.

4 Product overview

4.1 Function

–

Alternating pressurisation of the supply ports causes a piston in the gripper to

move (double-acting).

–

A gripper with integrated spring return is used to exert the gripper force. When

exhausting the single-acting gripper: the spring return moves the gripper jaws

to the initial position.

–N/O contact: NO (normally open)

–N/C contact: NC (normally closed)

–

The piston movement is transmitted mechanically to the gripper jaws. Gripper

fingers are fastened to the gripper jaws. Closing or opening the gripper fingers

clamps the payload to the outer contour (external gripping) or the inner contour

(internal gripping).

–

The gripping force is adjusted by external regulation of the operating pressure.

–The gripper has integrated fixed flow restrictors. If the max. gripper finger

weights and the max. gripper finger lengths are in compliance, an external flow

control is not required.

4.2 Structure

Fig. 1: Structure

Gripper jaw

Threaded hole for mounting

Locating hole

Supply port

Slot for proximity switch

Assembly

5.1

Preparing the gripper fingers

The gripper fingers are not included in the delivery.

Requirements for the gripper fingers

11 Technical data:

–

Observe the max. permissible forces and max. permissible torques at the

gripper jaw.

–Observe the max. length and max. weight.

–

Use gripper fingers that are as short and light as possible.

–

Manufacture gripper fingers that are suitable for the payload and type of grip-

ping action.

Size 6 10 16

Width at gripper jaws [mm] 4.3

–0.05

5.4

–0.05

Tab. 1:

Width of gripper jaws

Size 20 25 32 40

Width at gripper jaws [mm] 8.3

–0.05

15.2

–0.05

Tab. 2:

Width of gripper jaws

5.2

Mounting the gripper fingers

1 2 3 4

Fig. 2:

Mounting the gripper fingers

Screw

Gripper finger

Gripper jaw A

Gripper jaw A-...-1

Gripper jaw A-...-2

•

Position the prepared gripper fingers [2] on the gripper jaws [3], [4], [5] and

fasten each one with two screws [1]. Fix the gripper jaws in place during

mounting and use the specified tightening torque.

DHPC -6-... -10-...

A A-...-1 A-...-2 A A-...-1 A-...-2

Screw M3 M2 M3 M2.5

Tightening torque [Nm] 0.59 0.15 0.59 0.31

Tab. 3:

Dimensions and tightening torque

DHPC -16-... -20-...

A A-...-1 A-...-2 A A-...-1 A-...-2

Screw M3 M4

Tightening torque [Nm] 0.59 1.4

Tab. 4:

Dimensions and tightening torque

DHPC -25-... -32-...

A A-...-1 A-...-2 A A-...-1 A-...2

Screw M5 M6

Tightening torque [Nm] 2.8 4.9

Tab. 5: Dimensions and tightening torque

DHPC -40-...

A A-...-1 A-...-2

Screw M8

Tightening torque [Nm] 11.8

Tab. 6: Dimensions and tightening torque

5.3

Mounting gripper

If necessary, mount the proximity switches before mounting the gripper.

When using proximity switches for sensing the end position, take the following

into account:

• Interference from ferritic attachments, e.g. retaining screws made of ferritic

steel.

• Projecting proximity switches, if applicable.

• Cable outlet direction of the proximity switches.

• Sufficient space for the connection components.

• When sensing from both end positions: use separate slots for the proximity

switches.

Vertical mounting

1 2

Fig. 3:

Direct mounting via thread in

the housing

Thread

Locating hole

Size 6 10 16 20 25 32 40

Thread [1] M3 M4 M5 M6 M8

Depth of thread 10 4.75 6.75 9.6 13 15 18

Tightening torque [Nm] 0.88 0.69 2.1 4.3 7.9 10 18

Locating hole for centring@

pin [2]

[mm] – 2

Depth of locating hole [mm] – 3 4 5

Tab. 7:

Direct mounting via thread in the housing

1 2 3

Fig. 4:

Direct mounting via through-

hole

Thread

Locating hole (not for size 6)

Depth of locating hole (not for

size 6)

Size 6 10 16 20 25 32 40

Thread [1] M2.5 M2.5 M3 M4 M5 M6

Tightening torque [Nm] 0.49 0.49 0.88 2.1 4.3 7.3

Locating hole for centring@

pin [2]

[mm] – 2

Depth of locating hole [3] [mm] – 3 4 5

Tab. 8:

Direct mounting via through-hole

Horizontal mounting

Fig. 5: Horizontal mounting

Locating hole (not for size 6)

Thread

Size 6 10 16 20 25 32 40

Thread [2] M2 M3 M4 M5 M6 M8

Thread depth [mm] 4.5 4 4.5 7.5 10 13

Tightening torque [Nm] 0.15 0.9 1.6 3.3 5.9 13.7

Locating hole for centring@

pin [1]

[mm] – 2

Depth of locating hole [mm] – 3 3 4 5

Tab. 9: Horizontal mounting

Mounting on the bottom

2 3 4

Fig. 6:

Mounting on the bottom

Thread

Locating hole (not for size 6)

Positioning via base provided by

customer

Axial mounting by customer

Size 6 10 16 20 25 32 40

Thread [1] – M3 M4 M5 M6 M8

Thread depth [mm] – 4 6 10 12 13 17

Tightening torque [Nm] – 0.88 2.1 4.3 7.3 7.9 17.7

Locating hole for centring@

pin [2]

[mm] – 2

Depth of locating hole [mm] – 3 4 5

Positioning via base provided by customer [3]

Locating hole [mm] – 12@

Depth of locating hole [mm] – 1.5 2 3 3.5 4

Axial mounting by customer [4]

Clamping surface [mm] 8@

Clamping surface height [mm] 10 15 18 20 23

Tab. 10:

Mounting on the bottom

Installation

6.1 Pneumatic installation

NOTICE

Loss of function due to contamination in the connections.

• Keep ports and tubing lines free from dirt particles and foreign matter.

The use of a check valve prevents the payload from dropping in the event of

a sudden pressure drop. The use of a one-way flow control valve also permits

adjustment of the opening and closing time.

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	DHPC-L-16-A-B-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DHPC-L-16-A-B-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo DSNU-S-8-20-P-A-MQ Manual

21 Juni 2025

Festo DFM-40-100-B-PPV-A-KF Manual

21 Juni 2025

Festo DSNU-S-16-15-P-A-MQ Manual

21 Juni 2025

Festo MS4-EM1FR-1/4-D6-E-P-M-A8-WP-F1A-B Manual

21 Juni 2025

Festo VABM-B10-25-G12-4-P53 Manual

21 Juni 2025

Festo DSNU-S-25-200-PPS-A-MX Manual

21 Juni 2025

Festo CRDSNU-32-25-P-A Manual

21 Juni 2025

Festo DGST-25-200-E1A Manual

21 Juni 2025

Festo DFM-20-30-B-PPV-A-KF Manual

21 Juni 2025

Festo SDBF-FCS-1L-PU-K-9-N-LE Manual

21 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Life On Products LPRKC002 Manual

21 Juni 2025

Hoffman P2DO208HF Manual

21 Juni 2025

XP Gold Batea Kit Manual

21 Juni 2025

Zodiac Z200 M4 Manual

21 Juni 2025

Brady ROT1 Manual

21 Juni 2025

Fantini Cosmi A96 Manual

21 Juni 2025

Hoffman P2DO2216 Manual

21 Juni 2025

Fulgor Milano FUTWC 4500 TC FO MBK Manual

21 Juni 2025

Hansgrohe AXOR Montreux 16517950 Manual

21 Juni 2025

Nedis NBSTND500SI Manual

21 Juni 2025