Festo EHAM-MA-E19-25-C14 Manual

Festo Ikke kategoriseret EHAM-MA-E19-25-C14

Læs gratis den danske manual til Festo EHAM-MA-E19-25-C14 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Festo EHAM-MA-E19-25-C14, eller vil du spørge andre brugere om produktet?

Side 1/2
EHAM-MA-E19-25-C14
Adapter plate kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8159343
2021-08
[8159345]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
Document Product
User documents Actuators
User documents Modules
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Before working on the product, switch off the power supply and secure it
against being switched on again.
Observe further applicable documents.
Observe tightening torques.
2.2 Intended use
2.2.1 Use
Connection of modules and actuators.
2.2.2 Permissible components
Module Adapter plate kit Actuator
VTOI EHAM-MA-E19-25-C14 EGSC-...-25
EGSC-...-32
EGSK-20
EGSK-26
Tab. 2: Permissible components
3 Additional information
Contact the regional Festo contact if you have technical problems
è www.festo.com.
Accessories and spare parts è www.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
23456
7
8
Fig.1
1
Adapter plate (1x)
2
Centring pin (6x)
3
Screw (4x)
4
Screw (2x)
5
Washer (2x)
6
Hex nut (2x)
7
Screw (2x)
8
Mounting bracket (1x)
The kit contains all the mounting attachments that may be required. Some
mounting attachments will be left over.
4.2 Not in scope of delivery
9
10
Fig.2
9
Actuator (1x)
Mini slide EGSC
Electrical slide EGSK
10
Modul (1x)
Dispense head VTOI
5 Assembly
5.1 Preparation
Observe the labelling on the adapter plate.
P
Q
Fig. 3: Front side of the adapter plate
P
Drilled holes for screws
A EGSK-26
B EGSK-20
C EGSC-...-25
D EGSC-...-32
Q
Drill holes for VTOI
S
Fig. 4: Rear side of the adapter plate
S
Drilled holes for centring pins
A EGSK-26
B EGSK-20
C EGSC-...-25
D EGSC-...-32
5.2 Assembly
5.2.1 Preassembly
8
4
5
6
10
Fig. 5: Mounting bracket on VTOI
Attach the mounting bracket with the screws , the washers and the8 4 5
nuts to the module . Tightening torque: 0.5 Nm ± 10% 6 aJ
5.2.2 Connection VTOI with EGSC/EGSK
9
3
2
1S
P
Fig. 6: Mounting adapter plate on actuator
EGSC-...-25 EGSC-...-32 EGSK-20 EGSK-26
2Centring pin ZBS-2 ZBS-4 ZBS-2 ZBS-5
3Screw M3x8 M4x8 M3x8 M4x8
[Nm] 1.2 ± 20% 2.9 ± 10% 1.2 ± 20% 2.9 ± 10%
[P] Drilled hole C-C D-D B-B A-A
[S] Drilled hole C-C D-D B-B A-A
Tab. 3: Screw sizes and tightening torques
1. Position two centring pins in the corresponding drilled holes [S].2
2. Place the adapter plate over the centring pins on the actuator .1 2 9
3. Fasten the adapter plate with the screws over the corresponding drilled1 3
holes [P] on the actuator .9
Q
7
10
Fig. 7: Mounting module on adapter plate
1. Select the desired mounting position of 0° or 15° at the drilled holes [Q].
2. Use the screws to mount the module in the corresponding drilled7 aJ
holes [Q]. Tightening torque: 1.2 Nm ± 20%


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: EHAM-MA-E19-25-C14

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo EHAM-MA-E19-25-C14 stil et spørgsmål nedenfor, og andre brugere vil svare dig