Festo KYC-63 Manual


Læs gratis den danske manual til Festo KYC-63 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Festo KYC-63, eller vil du spørge andre brugere om produktet?

Side 1/2
KYC
Stop
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
8185824
2022-12c
[8185826]
8185824
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
LOCTITE243 is a registered trademark of its respective trademark holder in certain
countries.
1
Applicable documents
All available documents for the product
è
www.festo.com/sp.
Document Product Table of contents
Operating instruction Linear drive DGC(I)
Assembly instructions Shock absorber retainer DADP-
DGC
Tab. 1:
Applicable documents
2
Safety
2.1 Safety instructions
Only mount the product on components that are in a condition to be safely
operated.
Only use the product in its original condition without unauthorised modifica-
tions.
Observe the tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2
Intended use
The stop determines the end positions of the linear drive
slidesDGC-...-GF/-KF/-FA or DGCI:
Cushioned end position
Exact end position in any position with fixed stop
Use the stop only in combination with the shock absorber retainer DADP-DGC.
3 Additional information
Contact the regional Festo contact if you have technical problems
è
www.festo.com.
Accessories
è
www.festo.com/catalogue.
4
Product Range Overview
4.1 Scope of delivery
1
2
3
Fig. 1:
Scope of delivery KYC-18…-40
1
Housing (1x)
2
Stop (1x)
3
Screw (1x)
1
2
3
4
Fig. 2:
Scope of delivery KYC-50/-63
1
Housing (1x)
2
Stop (1x)
3
Screw (1x)
4
Washer (1x)
4.2 Not in scope of delivery
5
Fig.3
5
Linear drive (1x)
DGC-...-GF
DGC-...-KF,
DGC-...-FA,
DGCI
6
Fig.4
6
Shock absorber retainer (1x)
DADP-DGC
7
Fig.5
7
Shock absorber (1x)
YSR(W)-DGC
8
Fig.6
8
Screw locking compound (1x)
5 Assembly
5.1
Assembly of KYC-18…-40
1
2
3
A
Fig.7
1.
Clamp the housing firmly. Do not damage the profile lugs[A].1
2.
Orient the stop to the housing depending on the desired alignment on2 1
the linear drive .5
3.
Turn the screw above the housing to the stop . Observe the tight-3 1 2
ening torque.
KYC -18 -25 -32 -40
[Nm] 8 18 18 45
5.2 Assembly of KYC-50/-63
1
2
3
4
A
Fig.8
1. Clamp the housing firmly. Do not damage the profile lugs[A].1
2. Orient the stop to the housing depending on the desired alignment on2 1
the linear drive .5
3.
Turn the screw above the washer and the housing to the stop .3 4 1 2
Tightening torque: 70Nm
5.3
Mounting stop
2
5
Fig.9
When using customer-supplied spacer plates, take into account the projec-
tionH of the mounted stop compared to the linear drive .2 5


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: KYC-63

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo KYC-63 stil et spørgsmål nedenfor, og andre brugere vil svare dig