Festo MS9-SV Manual


Læs gratis den danske manual til Festo MS9-SV (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Festo MS9-SV, eller vil du spørge andre brugere om produktet?

Side 1/4
MS9-SV-...-C
Soft start/quick exhaust valve
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Operating instructions
8164018
2022-06a
[8164020]
Translation of the original instructions
© 2022 all rights reserved to Festo SE & Co. KG
1 About this document
This document describes the use of the soft start/quick exhaust valve.
The document contains additional information for use of the product in safety-
related systems (safety handbook in accordance with IEC 61508).
1.1 Target group
The document is targeted towards individuals who mount and operate the
product. It is additionally targeted towards individuals who are entrusted with
the planning and application of the product in a safety-oriented system.
1.2 Applicable documents
Assembly instructions for cover MS6/9-SV-C-MK/MH as tamper protection
All available documents for the product
è www.festo.com/sp.
1.3 Specified standards
Version
EN 60204-1:2016-10 EN ISO 13849-2:2012-10
EN ISO 4414:2010-11 EN ISO 14118:2018-02
EN ISO 13849-1:2015-12
Tab. 1: Standards specified in the document
2 Safety
2.1 Safety instructions
Only use the product in its original condition without unauthorised modifica-
tions.
Only use the product if it is in perfect technical condition.
Observe the identifications on the product.
Take into account the ambient conditions at the location of use.
Before working on the product, switch off the power supply and secure it
against being switched on again.
Observe the tightening torques. Unless otherwise specified, the tolerance is
± 20%.
Only use compressed air as an operating medium in accordance with the speci-
fication è 12 Technical data.
2.2 Intended use
The product is intended for mounting in machines or automation systems and is
only to be used as follows:
in an industrial environment
in its original condition, without unauthorised modifications
in safety-related systems only with cover MS9-SV-MK as tamper protection
in perfect technical condition
2.3 Foreseeable misuse
Foreseeable misuse includes:
outdoor operation
Bypassing of safety functions
use in reversible operation with reversal of supply air and exhaust air
use in "Low Demand Mode" according to EN 61511
vacuum operation
2.4 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can
evaluate the work and detect dangers. The qualified personnel have skills and
experience in dealing with electropneumatic (open-loop) control technology.
3 Additional information
Contact the regional Festo contact if you have technical problems
è www.festo.com.
Accessories è www.festo.com/catalogue.
Designation Type
Silencer U-1-B
Cover, covers the manual override MS9-SV-MH
Cover, covers the adjustment elements for the pressure switching point, the
main flow control and the manual override
MS9-SV-MK
Tab. 2: Accessories
4 Product overview
4.1 Structure
4.1.1 Product design
1
2
3
4
5
6
7
8
9
Fig. 1: Operating elements and
connections
1
Pilot solenoid valve
2
Manual override at the soft-start/quick
exhaust valve
3
Pneumatic port 1 (compressed air
inlet)
4
Pneumatic port 3 (exhaust)
5
Silencer
6
Manual override at the pilot solenoid
valve
7
Flow control screw for setting the
filling time
8
Adjusting screw for setting the pres-
sure switch point
9
Pneumatic port 2 (compressed air
outlet port)
4.1.2 Product variants
The following table lists selected product characteristics and codes that are
necessary for understanding the instruction manual. Complete type code
è www.festo.com/catalogue.
Key features Code Description
Series MS Standard service unit
Size 9 Grid dimension 90 mm
Function -SV Soft-start/quick exhaust valve
Port size -3/4 Thread G 3/4
-1 Thread G 1
-AGD Sub-base G 1/2
-AGE Sub-base G 3/4
-AGF Sub-base G 1
-AGG Sub-base G 1 1/4
-AGH Sub-base G 1 1/2
-N3/4 Thread N 3/4
-N1 Thread N 1
-AQR Sub-base NPT 1/2
-AQS Sub-base NPT 3/4
-AQT Sub-base NPT 1
-AQU Sub-base NPT 1 1/4
-AQV Sub-base NPT 1 1/2
-G Module without connection thread, without sub-base
-NG Module without connection thread, without sub-base (port 3 in
NPT)
Performance Level -C in accordance with EN ISO 13849-1
Supply voltage -V24 24 V DC (plug pattern in accordance with EN 175301-803, type C)
-10V24P 24 V DC (M12 in accordance with IEC 61076-2-101)
-V110 110 V AC (plug pattern in accordance with EN 175301-803,
type C)
-V230 230 V AC (plug pattern in accordance with EN 175301-803,
type C)
Options -S Silencer
Tamper protection -MH Cover - manual override (HHB) only
-MK Cover – pressure switching point (DUP) and main flow control
valve (HD) adjusting screws, manual override (HHB)
Tab. 3: Product variants (selection)
4.2 Function
The MS9-SV-...-C electro-pneumatic pressure soft-start/quick exhaust valve is
intended for rapid pressure reduction and pressurisation in pneumatic line sys-
tems and terminal equipment in industry.
Circuit symbol Function
Soft-start/quick exhaust valve, electro-pneumatically actuated
Tab. 4: Circuit symbol for the function
4.3 Information on functional safety
4.3.1 Achievable safety rating
The product is suitable for use as an element in a safety-related system in accord-
ance with EN ISO 13849-1 up to category 1, performance level (PL) c.
NOTICE
The suitability for certain applications can only be determined in connection with
the assessment of further components of the subsystem. These must achieve the
same safety level.
4.3.2 Safety functions
The safety functions are:
Exhausting in the downstream piping system and terminals
Prevention of unexpected start-up (pressurisation)
The safety functions are triggered by switching off the power supply at the pilot
solenoid valve. As long as the voltage at the pilot solenoid valve remains switched
off, the connection between ports 2 and 3 is enabled è 4.2 Function.
This switching position represents the safe state.
4.3.3 Operating conditions
General information on safe operation è 2 Safety
Ambient conditions and additional technical specifications è 12 Technical
data.
NOTICE
Actuate the product at least once per month to ensure the safety function works
properly.
4.3.4 Limitations of use
The duration of use is limited to the maximum operating time T10d or is no more
than the mission time TM è 4.3.5 Characteristic values.
4.3.5 Characteristic values
Safety characteristics MS9-SV...-C
Safety function Exhaust
Prevention of unexpected start-up (pressurisation)
Note on forced checking
procedure1)
Switching frequency min. 1/month
Performance level (PL)
in accordance with
EN ISO 13849-1
Exhaust: up to category 1, PL c2)
Service life characteristic B10 0.35 mill. switching cycles
Service life T M
[a] 20
Maximum operating time T10d
[a] 2 x B10/nop or max. TM
Diagnostic coverage
(Diagnostic Coverage)
DC 0
Hardware fault tolerance
(Hardware Fault Tolerance)
HFT 0
Average probability of dan-
gerous failure per hour
(Average probability of dan-
gerous failure per hour)
PFHdè Fig. 2
Exhaust time [s] è 12.4 Exhaust time
CE marking, Declaration of conformity è www.festo.com/sp
1) Use in "low demand mode" is not permissible.
2) Applies up to the average number of actuations per year = 180,000
Tab. 5: Safety characteristics
Fig. 2: PFHd value, dependent on the average number of operations per year (n
op)
5 Assembly
Information about mounting the module connector, connecting plate and
mounting bracket can be found in the instruction manual enclosed with the
relevant accessories.
5.1 Requirements
Take appropriate measures to remove any particles in the supply lines.
5.2 Preparation
12
Fig. 3: Flow direction
1
Digit 1 for port 1
2
Digit 2 for port 2
Place product as close as possible to the installation site.
Place the product so that there is enough space for removing and installing the
silencer.
Observe the flow direction from port 1 to port 2. The numbers and on the1 2
housing of the MS9-SV-...-C serve as orientation.
5.3 Assembly with MS-series service unit components
WARNING
Loss of the safety function
If devices that impair the exhaust are placed behind the pneumatic connection 2
of the soft start/quick exhaust valve, this can result in loss of the safety function.
Only place devices that do not impair the exhaust downstream of pneumatic
connection 2.
1 2
Fig. 4: Assembly
1
Seal
2
Module connector
1. Insert a seal between the individual devices (module connector MS9-MV in1
scope of delivery).
2. Place the module connector in the slots of the separate devices.2
3. Fasten the module connector with two screws (in scope of delivery of module
connector MS9-MV). Maximum tightening torque 1.2 Nm
6 Installation
6.1 Safety
WARNING
Risk of injury from compressed air.
Before carrying out installation and maintenance work, switch off the com-
pressed air supply.
6.2 Pneumatic installation
Port 1 and 2
If using screw connectors:
ISO 228 NPT
MS9-…-3/4 18.5 mm MS9-…-N3/4 18.5 mm
MS9-…-1 18.5 mm MS9-…-N1 18.5 mm
MS9-…-AGD/AGE/AGF 18.5 mm MS9-…-AQR/AQS/AQT 18.5 mm
MS9-…-AGG/AGH 31.5 mm MS9-…-AQU/AQV 31.5 mm
Tab. 6: Max. screw-in depth
1. Note the permissible screw-in depth of the connector thread.


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: MS9-SV

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo MS9-SV stil et spørgsmål nedenfor, og andre brugere vil svare dig