Festo NEBM-L10G14-EH-10-Q6N-LE12 Manual

Festo Ikke kategoriseret NEBM-L10G14-EH-10-Q6N-LE12

Læs gratis den danske manual til Festo NEBM-L10G14-EH-10-Q6N-LE12 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Festo NEBM-L10G14-EH-10-Q6N-LE12, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

NEBM-L10G14-EH-...-Q...-LE12

Motor cable

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Assembly instructions

8156480

2024-03

[8156482]

8156480

Original instructions

Applicable documents

All available documents for the product

www.festo.com/sp.

2 Safety

2.1

Safety instructions

–Before working on the product: Switch off the power supply, ensure that it is off

and secure it against being switched on again.

2.2 Intended use

The motor cable connects the stepper motor EMMB-ST with the servo drive

CMMT-ST.

2.3

Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can

evaluate the work and detect dangers. The qualified personnel are trained in

electrical engineering.

3 Additional information

–Contact the regional Festo contact if you have technical problems

www.festo.com.

–

Accessories

www.festo.com/catalogue.

4 Structure

4.1

Product design

1 2

Fig. 1:

Product design

Hybrid socket L10

Wire end (12x)

Shielded connection

Cable

Contact assignment identification

4.2

Contact assignment for motor and brake

Electrical connection1

Field device side

Signal Electrical connection2

Controller side X6

[1]Hybrid socket [2]Wire ends

1 Phase A RD

2 Phase A/ BN

3 BR+ GNWH

4 BR- BUWH

5 Shielding –

6 Not assigned –

13 Phase B BK

14 Phase B/ WH

Colour code in accordance with IEC 60757:2021-06

Tab. 1: Contact assignment for motor and brake

4.3 Encoder contact assignment

Electrical connection1

Field device side

Signal Electrical connection2

Controller side X2

[1]Hybrid socket [2]Wire ends

7 SLO+ VT

8 SLO- YE

9 MA+ GY

10 MA- PK

11 +5V RD

12 GND(0V) BU

1) Colour code in accordance with IEC 60757:2021-06

Tab. 2: Encoder contact assignment

Mounting

5.1

Mounting electrical connection1

1. Align the hybrid socket[1].

Plug the hybrid socket[1] into the connection and click it into place.

5.2

Strain relief for electrical connection 1

• Fix the cable sheath in the section before the hybrid socket.

No strain on the hybrid socket.

5.3

Mounting electrical connection2

Attach the shield connection[3] to the servo drive with the shield clamp

èServo drive operating instructions CMMT-ST.

Connect the wire ends[2] in accordance with the contact assignment. Note

the contact assignment identification[5].

5.4

Strain relief for electrical connection 2

•

Fix the cable sheath in the area in front of the wire ends.

No strain on the wires.

5.5

Wiring

Character-

istics

Cable characteristics Wiring

-E Suitability for energy chains In energy chain or flexible

Tab. 3:

Wiring

5.6

Mounting in energy chain

Lay out the energy chain lengthways.

Place the cables in the energy chain without twisting them.

Separate cables from each other using separators/drilled holes.

Do not bind cables in bundles.

Maintain spaceX. X 10%of the cable diameterD.>

With the energy chain hanging vertically: increase the spaceX.

Align the energy chain in the working position:

–

Make sure that the radius is greater than the bending radiusR of the

cables.

–The cables can move freely in the bending radius KR of the energy chain.

The cable movement is not forced by the energy chain.

7. Mount the energy chain corresponding instruction manual.è

Fasten the cables:

–for short energy chains with a length 1m at both ends of the energy<

chain

–for long sliding energy chains with a length 1m at the driver end only>

9. Do not move cables all the way to the fastening point.

The mounting spaceA between the fastening point and bending move-

ment is maintained.

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	NEBM-L10G14-EH-10-Q6N-LE12

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo NEBM-L10G14-EH-10-Q6N-LE12 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM E43416 Manual

2 Januar 2026

Pyle PCRMP2DY Manual

2 Januar 2026

Testboy TV 285 Manual

2 Januar 2026

Pioneer 2AM700 Manual

2 Januar 2026

Ruvati RVH7419 Manual

2 Januar 2026

Vaxcel T0703 Manual

2 Januar 2026

Govee H1167 Manual

2 Januar 2026

Ruvati RVH9733 Manual

2 Januar 2026

Sonnenkönig Slim E 1000 Manual

2 Januar 2026

Asus Prime AP202 Manual

2 Januar 2026