Festo PAML-CP-90-HP3-G34 Manual

Festo Ikke kategoriseret PAML-CP-90-HP3-G34

Læs gratis den danske manual til Festo PAML-CP-90-HP3-G34 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Festo PAML-CP-90-HP3-G34, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PAML-CP/-MB/-MK-90

Sub-base/Mounting bracket/Module connector

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Assembly instructions

8161942

2021-10b

[8161944]

Translation of the original instructions

1 Applicable documents

All available documents for the product

è www.festo.com/sp.

2 Safety

2.1 Safety instructions

–Only use the product in its original condition without unauthorised modifica-

tions.

–Only use the product if it is in perfect technical condition.

–Take the weight of an individual device or a service unit into account.

Dependent on the design, a mounted service unit can weigh more than 50 kg.

–Under intended use the surface temperature may reach 60 °C. Allow the device

to cool down before working on it.

–Make sure the mounting surface is sufficiently strong for the maximum forces.

–Only use suitable mounting components.

–Mount the individual device or the service unit only on flat surfaces.

2.2 Intended use

–The sub-base PAML-CP serves as an adapter for the pneumatic connection and

for pipe mounting for in-line installation of service units.

–The mounting bracket PAML-MB is used for connection and wall mounting of

individual devices or service units.

–The module connector PAML-MK is used to connect two service units of the

same size.

2.3 Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can eval-

uate the work and detect dangers. Personnel must have the relevant mechanical

training.

3 Additional Information

–Accessories è www.festo.com/catalogue.

4 Product Range Overview

4.1 Scope of delivery

Fig. 1: Sub-base PAML-CP-90-HP3-G12

Front plate (1x)

Rear plate (1x)

Screw (8x)

Washer (8x)

O-ring (2x)

Fig. 2: Sub-base PAML-CP-90-HP3-G114

Front plate (1x)

Rear plate (1x)

O-ring (2x)

141516

Fig. 3: Mounting bracket PAML-MB-90-HP3

Wall bracket (1x)

O-ring (1x)

Front plate (1x)

Screw (2x)

Rear plate (1x)

Sleeve (2x)

Screw (2x)

Retaining screw (1x)

Fig. 4: Module connector PAML-MK-90-HP3

Screw (2x)

Front plate (1x)

O-ring (1x)

Rear plate (1x)

4.2 Not in scope of delivery

Fig.5

Electrical pressure regulator (1x)

PREL-90

Branching module (1x)

PMBL-90

5 Assembly

Some O-rings will be left over with some mounting variants.

5.1 Mounting the connecting plates PAML-CP

Size G1/4 … G1

Fig.6

1. Orient the front plate and the rear plate so that the stamp number of1 2

the sub-base corresponds to the stamp number on the housing (1 to 1 and

2 to 2).

2. Insert the O-rings in the slots provided.5

3. Position the front plate and the rear plate .1 2

4. Fasten the front plate and the rear plate to the service unit using four1 2

screws and four washers . Tightening torque: 12 Nm ± 10% 3 4

5. Comply with the maximum screw-in depth for the pipe connection.

ISO 228 Max. screw-in depth [mm]

G1/2 12

G1/3 14

G1/2 16

G1 18

Size G1 1/4

Fig.7

1. Orient the front plate and the rear plate so that the stamp number of6 7

the sub-base corresponds to the stamp number on the housing (1 to 1 and

2 to 2).

2. Insert the O-rings or in the slots provided.8 aI

3. Position the front plate and the rear plate .6 7

4. Fasten the front plate and the rear plate to the service unit using theaH bJ

screws . Tightening torque: 12 Nm ± 10% aG

5. Observe the maximum screw-in depth for the pipe connection in accordance

with ISO 228: 20 mm

5.2 Mounting the mounting brackets PAML-MB

Always mount an individual device with two mounting brackets. Mount a service

unit with a mounting bracket at both the beginning and the end of the service unit

string and between the individual service units.

The grid width for he filter PFML-90 is 135 mm.

Fasten all required wall brackets with two M8 screws each at the specified9 bD

locations. The standard grid width between the wall brackets is 90 mm, and9

the distance in height between holes is 145 mm. All retaining screws mustaF

point upwards.

6 8

Fig.8

1. Orient the front plate 6 7 and the rear plate so that the stamp number of

the sub-base corresponds to the stamp number on the housing (1 to 1 and

2 to 2).

2. Insert the O-rings in the slots provided.8

3. Position the front plate and the rear plate .6 7

4. Push the screws into the front plate .aB aA

5. Place the seals between the service units.aJ

6. Place the front plate and rear plate in the slots of the service units.aA aC

7. Screw the screws into the rear plates . Tightening torque: 10 Nm ± 10% aB aC

8. Unscrew the retaining screws .aF

9. Position the service unit combination with the lugs in the slots of the wallaE

brackets .9

10. Tighten the retaining screws . Tightening torque: 2 Nm ± 10% aF

5.3 Assembly of the module connector PAML-MK

23 17

Fig.9

1. Note the flow direction from 1 to 2. The numbers on the product housing bC

serve as orientation.

2. Insert the retaining screws through the holes in the front plate .aG aH

3. Place the seal between the service units.aI

4. Place the front plate and rear plate in the slots of the service units.aH bJ

5. Tighten the screws . Tightening torque: 10 Nm ± 10% aG

6 Disassembly

1. Depressurise the system.

2. Check the surface temperature of the device. If necessary, let the device cool

down.

3. Remove the existing service unit string.

7 Technical data

PAML -CP -MB -MK

Operating pressure [MPa] 0 … 5

[bar] 0 … 50

[psi] 0 … 725

Temperature of medium [°C] +5 … +60

Ambient temperature [°C] +5 … +60

Tab. 1: Technical data

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	PAML-CP-90-HP3-G34

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo PAML-CP-90-HP3-G34 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025