Festo PAML-MB-90-HP3 Manual

Festo Ikke kategoriseret PAML-MB-90-HP3

Læs gratis den danske manual til Festo PAML-MB-90-HP3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Festo PAML-MB-90-HP3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
PAML-CP/-MB/-MK-90
Sub-base/Mounting bracket/Module connector
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8161942
2021-10b
[8161944]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety instructions
–Only use the product in its original condition without unauthorised modifica-
tions.
–Only use the product if it is in perfect technical condition.
–Take the weight of an individual device or a service unit into account.
Dependent on the design, a mounted service unit can weigh more than 50 kg.
–Under intended use the surface temperature may reach 60 °C. Allow the device
to cool down before working on it.
–Make sure the mounting surface is sufficiently strong for the maximum forces.
–Only use suitable mounting components.
–Mount the individual device or the service unit only on flat surfaces.
2.2 Intended use
–The sub-base PAML-CP serves as an adapter for the pneumatic connection and
for pipe mounting for in-line installation of service units.
–The mounting bracket PAML-MB is used for connection and wall mounting of
individual devices or service units.
–The module connector PAML-MK is used to connect two service units of the
same size.
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval-
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional Information
–Accessories è www.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
2
1
3
4
5
Fig. 1: Sub-base PAML-CP-90-HP3-G12
1
Front plate (1x)
2
Rear plate (1x)
3
Screw (8x)
4
Washer (8x)
5
O-ring (2x)
6
7
8
Fig. 2: Sub-base PAML-CP-90-HP3-G114
6
Front plate (1x)
7
Rear plate (1x)
8
O-ring (2x)
9
10
11
12
13
141516
Fig. 3: Mounting bracket PAML-MB-90-HP3
9
Wall bracket (1x)
10
O-ring (1x)
11
Front plate (1x)
12
Screw (2x)
13
Rear plate (1x)
14
Sleeve (2x)
15
Screw (2x)
16
Retaining screw (1x)
17
18
19
20
Fig. 4: Module connector PAML-MK-90-HP3
17
Screw (2x)
18
Front plate (1x)
19
O-ring (1x)
20
Rear plate (1x)
4.2 Not in scope of delivery
21
22
Fig.5
21
Electrical pressure regulator (1x)
PREL-90
22
Branching module (1x)
PMBL-90
5 Assembly
Some O-rings will be left over with some mounting variants.
5.1 Mounting the connecting plates PAML-CP
Size G1/4 … G1
2
1
4
5
3
Fig.6
1. Orient the front plate and the rear plate so that the stamp number of1 2
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.5
3. Position the front plate and the rear plate .1 2
4. Fasten the front plate and the rear plate to the service unit using four1 2
screws and four washers . Tightening torque: 12 Nm ± 10% 3 4
5. Comply with the maximum screw-in depth for the pipe connection.
ISO 228 Max. screw-in depth [mm]
G1/2 12
G1/3 14
G1/2 16
G1 18
Size G1 1/4
7
6
17
18
19
20
Fig.7
1. Orient the front plate and the rear plate so that the stamp number of6 7
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings or in the slots provided.8 aI
3. Position the front plate and the rear plate .6 7
4. Fasten the front plate and the rear plate to the service unit using theaH bJ
screws . Tightening torque: 12 Nm ± 10% aG
5. Observe the maximum screw-in depth for the pipe connection in accordance
with ISO 228: 20 mm
5.2 Mounting the mounting brackets PAML-MB
Always mount an individual device with two mounting brackets. Mount a service
unit with a mounting bracket at both the beginning and the end of the service unit
string and between the individual service units.
The grid width for he filter PFML-90 is 135 mm.
Fasten all required wall brackets with two M8 screws each at the specified9 bD
locations. The standard grid width between the wall brackets is 90 mm, and9
the distance in height between holes is 145 mm. All retaining screws mustaF
point upwards.
9
10
11
12
13
14
15
16
24
7
6 8
Fig.8
1. Orient the front plate 6 7 and the rear plate so that the stamp number of
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.8
3. Position the front plate and the rear plate .6 7
4. Push the screws into the front plate .aB aA
5. Place the seals between the service units.aJ
6. Place the front plate and rear plate in the slots of the service units.aA aC
7. Screw the screws into the rear plates . Tightening torque: 10 Nm ± 10% aB aC
8. Unscrew the retaining screws .aF
9. Position the service unit combination with the lugs in the slots of the wallaE
brackets .9
10. Tighten the retaining screws . Tightening torque: 2 Nm ± 10% aF
5.3 Assembly of the module connector PAML-MK
23 17
18
19
20
Fig.9
1. Note the flow direction from 1 to 2. The numbers on the product housing bC
serve as orientation.
2. Insert the retaining screws through the holes in the front plate .aG aH
3. Place the seal between the service units.aI
4. Place the front plate and rear plate in the slots of the service units.aH bJ
5. Tighten the screws . Tightening torque: 10 Nm ± 10% aG
6 Disassembly
1. Depressurise the system.
2. Check the surface temperature of the device. If necessary, let the device cool
down.
3. Remove the existing service unit string.
7 Technical data
PAML -CP -MB -MK
Operating pressure [MPa] 0 … 5
[bar] 0 … 50
[psi] 0 … 725
Temperature of medium [°C] +5 … +60
Ambient temperature [°C] +5 … +60
Tab. 1: Technical data

Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: PAML-MB-90-HP3

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo PAML-MB-90-HP3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Festo Manualer

Festo

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025
Festo

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025
Festo

Festo VABD-S2-1-S-C Manual

20 August 2025
Festo

Festo SIED-M18B-ZO-S-L Manual

19 August 2025
Festo

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025
Festo

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-CO-DE Manual

19 August 2025
Festo

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025
Festo

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo

Kimo LR 110 Manual

2 September 2025
HMS Premium

HMS Premium LPD02 Manual

2 September 2025
AVer

AVer E1008 Manual

2 September 2025
Biltema

Biltema 17-547 Manual

2 September 2025
Groen

Groen AH/1E Manual

2 September 2025
ACOPower

ACOPower HY-P30 Manual

2 September 2025
Yamaha

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025
Globe

Globe RG30 Manual

2 September 2025
Deye

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025
Neutrik

Neutrik NLT4FXX Manual

2 September 2025