Festo SDE3 Manual

Festo Ikke kategoriseret SDE3

Læs gratis den danske manual til Festo SDE3 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Festo SDE3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
Pressure sensor SDE3
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Operating instructions
Original instructions
8078143
2017-09f
[8078145]
English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For all available product documentation è www.festo.com/pk
1 Operating elements and connections
1 2 3 4
789
aJ
aA
aB
aC
aD
5
6
1SDE3 for mounting onto a wall or
H-rail
2Adapter plate for wall mounting
3Electrical connection
4SDE3 for front panel mounting
5Clamping plate for front panel
mounting
6Mounting slide (rear)
7Compressed air or vacuum
connections (only SDE3-...D and
SDE3-...M)
8Compressed air or vacuum
connection (only SDE3-...S)
9Compressed air or vacuum
connections (only SDE3-...Z)
aJ Label holder
aA B pushbutton
aB A pushbutton
aC Edit button
aD Display
Fig. 1
Key feature Order
code
Type
Function SDE3 Pressure sensor
Pressure measuring range -V1 0 … –1
-B2 –1 … +1
-D2 0 … 2
-D6 0 … 6
-D10 0 … 10
-D12 1) 0 … 12
Supply port S 1x relative pressure
D 2x relative pressure
Z 1x differential pressure
M 2x relative pressure, 1x differential pressure analysis
Feature Order
code
Type
Display -B Values in bar
-P Values in psi
-K 2) Values in kPa
-H Values in inches of mercury
-W 3) Values in inches of water
Mounting/pneumatic
connection
-HQ4 H-rail mounting, push-in connector 4 mm
-WQ4 Wall mounting, push-in connector 4 mm
-FQ4 Front panel mounting, push-in connector 4 mm
-HT532 H-rail mounting, push-in connector 5/32”
-WT532 Wall mounting, push-in connector 5/32”
-FT532 Front panel mounting, push-in connector 5/32”
Electrical output -2P 2 switching outputs PNP
-2N 2 switching outputs NPN
Electrical connection -M8 Plug connector M8x1
-M12 Plug connector M12, A-coded
-K Cable 2.5 m
Electrical accessories 4) -G Connecting cable, straight socket, cable length 2.5 m
-W Connecting cable, angled plug socket, cable length
2.5 m
-G5 Connecting cable, straight socket, cable length 5 m
-W5 Connecting cable, angled plug socket, cable length 5 m
1) Key feature only on request
2) Not for SDE3-D12M
3) Not for SDE3-D6M, SDE3-D10M, SDE3-D12M
4) Only in combination with key feature -M8 or -M12
Fig. 2
2 Function and application
The SDE3 has been designed for monitoring changes in pressure in the
compressed air system or terminals. Variants for relative pressure measurement
and differential pressure measurement are available:
Type Description Input
values1)
Switching
outputs
SDE3-...Z 1x differential pressure
p1 – p2 2)
In A Out A, Out B
SDE3-...S 1x relative pressure In A Out A, Out B
SDE3-...D 1x relative pressure pA In A Out A
1x relative pressure pB In B Out B
SDE3-...M 1x relative pressure pA In A Out A
1x relative pressure pB In B –
1x differential pressure
analysis pB – pA
In C Out B
SDE3-…V1M 1x differential pressure
analysis pA – pB
In C Out B
1) In A/B: input value for sensor element A/B. In C: calculated
2) Measuring pressure p1 – reference pressure p2
Fig. 3
3 Requirements for product use
Warning
Depending on the functions of the machine/system, the manipulation of signal
statuses can cause serious injury to people or material damage.
Note that if the switching characteristics of the switching outputs is modified
in EDIT mode, the new status becomes effective immediately.
Enable the password protection option (security code) to prevent accidental
alteration by an unauthorised third party (è Chapter 5.3 section Set security
code).
Warning
The usage of the SDE3 in combination with impermissible media can lead to
personal injury or material damage.
Use the SDE3 only with compressed air
Observe the specified air quality class (è Chapter 11 Technical data).
Note
Improper handling can result in malfunctions.
Make sure that the following specifications are always observed.
Compare the limit values contained in these operating instructions with those of
your application (e.g. operating media, pressures, forces, torques,
temperatures, masses, speeds, voltages).
Take the ambient conditions at the location of use into consideration.
Comply with the regulations of the workers’ compensation trade association,
the German Technical Control Board (TÜV), of the VDE or relevant national
regulations.
Remove all transport packing, such as protective wax, foils (polyamide),
caps(polyethylene), cardboard boxes (except for the sealing elements of the
pneumatic connections).
The material used in the packaging has been specifically chosen for its
recyclability (exception: oiled paper = residual waste).
Use the product in its original status. Unauthorised modification is not
permitted.
The device is intended for use in an industrial environment. Measures may need
to be implemented in residential areas for interference suppression.
Range of applications and certifications
The information in this section, in combination with the UL marking on the product,
must be observed in order for there to be compliance with the certification
conditions of Underwriters Laboratories Inc. (UL) for USA and Canada. Observe the
following English-language remarks from UL:
This device is intended to be used with a Class 2 power source or Class 2
transformer in accordance with UL1310 or UL1585.
As an alternative a LV/C (Limited Voltage/Current) power source with one of the
following properties can be used:
– This device shall be used with a suitable isolating source such that the
maximum open circuit voltage potential available to the product is not more
than 30 V DC and the current is limited to a value not exceeding 8 amperes
measured after 1 minute of operation.
– This device shall be used with a suitable isolating source in conjunction with
afuse in accordance with UL248. The fuse shall be rated max. 3.3 A and be
installed in the 30 V DC power supply to the device in order to limit the available
current.
Note that, when more than one power supply or isolating device is used,
connection in parallel is not permitted.
In determining the acceptability of the combination, the following details are to be
examined:
– The suitability of the final mounting is to be determined.
– The devices are to be mounted in an enclosure with adequate strength and
thickness.
– The devices have not been investigated for field wiring. The suitability of the
final application is to be determined.
UL approval information
Product category code NRNT2 (USA) or
NRNT8 (Canada)
File number E253738
Considered standards UL 508, 17th edition,
C22.2 No. 14-95
UL mark
Fig. 4
4 Installation
4.1 Mechanical system
Note
Mount the SDE3 and connect the tubing so that no condensation from the
compressed air lines can gather in the device.
It can be mounted in any position. Mount the SDE3 as follows:
H-rail (manifold assembly)
1. Hang the SDE3 into the H-rail.
2. Press the SDE3 in the direction of the
arrow until the mounting slide catches
è Fig. 5.
Fig. 5
Wall mounting
Observe the hole pattern (è Fig. 24)
1. Attach the adapter plate, for example,
with two screws M3.
2. Hang the SDE3 into the adapter plate.
3. Press the SDE3 in the direction of the
arrow until the mounting slide catches
è Fig. 6. Fig. 6
Plate mounting (threaded mounting)
Observe the hole pattern (è Fig. 24)
Mount the SDE3 with washers and
screws M3 (è Fig. 7).
Max. tightening torque 0.5 Nm
Fig. 7
Front panel mounting
1. Push the SDE3 into the recess
(70x22 mm) in the front panel.
2. Hang the clamping plate and press it
until the mounting slide locks into place.
3. Screw in the screws M3 with washers
(è Fig. 8).
Max. tightening torque 0.3 Nm
In case of thin front panels (s < 2 mm),
washers might not be necessary.
Fig. 8
4.2 Pneumatic system
Connect the tubing of SDE3 as follows:
Insert the tube into the push-in fittings. Make sure the system is connected
correctly (è Fig. 3).
4.3 Electrical system
Warning
Use only power sources which guarantee reliable electrical isolation of
theoperating voltage as per IEC/EN 60204-1. Observe also the general
requirements for PELV power circuits as per IEC/EN 60204-1.
Note
Long signal lines pick up more interference.
Make sure that the signal lines are always shorter than 30 m.
Wire the SDE3 as follows:
Pin Allocation Core colours1) Plug connectors2)
1 Supply voltage
+24 V DC
Brown (BN) 4-pin M8 5-pin M12x1
5
2
3
4
1
2 Switching output B
(Out B)
White (WH)
3 0 V Blue (BU)
4 Switching output A
(Out A)
Black (BK)
5 n.c. –
1) In case of SDE3-…-K and/or the usage of the plug socket with the cable (è www.festo.com/catalogue)
2) Tightening torque for the union nut on plug connector M8: max. 0.3 Nm; on plug connector M12:
max. 0.5 Nm.
Fig. 9

Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: SDE3

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo SDE3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Festo Manualer

Festo

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025
Festo

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025
Festo

Festo VABD-S2-1-S-C Manual

20 August 2025
Festo

Festo SIED-M18B-ZO-S-L Manual

19 August 2025
Festo

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025
Festo

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-CO-DE Manual

19 August 2025
Festo

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025
Festo

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo

Kimo LR 110 Manual

2 September 2025
HMS Premium

HMS Premium LPD02 Manual

2 September 2025
AVer

AVer E1008 Manual

2 September 2025
Biltema

Biltema 17-547 Manual

2 September 2025
Groen

Groen AH/1E Manual

2 September 2025
ACOPower

ACOPower HY-P30 Manual

2 September 2025
Yamaha

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025
Globe

Globe RG30 Manual

2 September 2025
Deye

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025
Neutrik

Neutrik NLT4FXX Manual

2 September 2025