Festo SMAT-8M-U-E-2,5-OE Manual

Festo Ikke kategoriseret SMAT-8M-U-E-2,5-OE

Læs gratis den danske manual til Festo SMAT-8M-U-E-2,5-OE (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Festo SMAT-8M-U-E-2,5-OE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SMAT-8M

Position transmitter

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Operating instruction

8203946

2023-12h

[8203948]

8203946

Translation of the original instructions

1 Applicable documents

All available documents for the product

èwww.festo.com/sp.

2 Safety

2.1 General safety instructions

–Only use the product if it is in perfect technical condition.

2.2 Intended use

This product is intended for proximity sensing of the piston position of Festo

drives that can be detected magnetically. The device is intended for use in an

industrial environment.

It is suitable for use with Festo Festo drives with T-slot (profile slot8) and round

cylinders and tie-rod cylinders with mounting kitsèwww.festo.com/catalogue.

2.3 Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can

evaluate the work and detect dangers. The qualified personnel have skills and

experience in dealing with electrical (open-loop) control technology.

2.4 UL/CSA Certification

In combination with the UL inspection mark on the product, the information in this

section must also be observed in order to comply with the certification conditions

of Underwriters Laboratories Inc. (UL) for USA and Canada.

UL/CSA certification information

Product category code NRKH, NRKH7

File number E232949

Considered standards UL 60947-1

UL 60947-5-2

CAN/CSA C22.2 No. 60947-1

CAN/CSA C22.2 No. 60947-5-2

UL mark

UL control number Industrial Control Equipment 2MD1

Tab. 1: UL/CSA certification information

Only for connection to a NEC/CEC Class 2 supply.

Locally installed conductors for the position transmitter must be separated from

the on-site and factory-installed conductors and uninsulated live parts of other

circuits that operate with more than 150V to earth. A permanent minimum

distance of 50.8mm (2inches) must be observed. If the locally installed conduc-

tors have been provided with approved insulating material that has an identical

or higher rated operating voltage than the other circuit involved, the minimum

distance need not be observed.

3 Additional information

–Contact the regional Festo contact if you have technical problems

èwww.festo.com.

–Accessories and spare parts èwww.festo.com/catalogue.

4 Product overview

4.1 Configuration

Fig. 1: Design of SMAT-8M

Retaining screw

Connecting cable, depending on

the version with a rotatable M8

plug or cable with open end

Red LED: piston not in sensing

range

Green LED: piston in sensing

range

4.2 Function

The position transmitter SMAT-8M is an electronic position transmitter with a 3D

Hall sensor arrangement, integrated signal processing, analogue voltage output

and optical operating status display.

The magnetic field of the piston magnet is detected, the magnetic field compo-

nents are evaluated internally and output within the sensing range as an ana-

logue displacement-proportional signal at the output. The sensing range varies

depending on the cylinder.

5 Assembly

Any mounting position can be used.

Fig. 2: Mounting

Internal hex key, spanner size

1.5mm

T-slot

1. Place the position transmitter in the T-slot of the drive.

2. Tighten the retaining screw.

–Maximum tightening torque: 0.3Nm

6 Installation, electrical

WARNING

Risk of injury due to electric shock.

• Use exclusively PELV circuits in accordance with IEC60204-1/EN60204-1 for

the electrical power supply (Protective Extra-Low Voltage, PELV).

• Observe the general requirements of IEC60204-1/EN60204-1 for PELV cir-

cuits.

• Use exclusively voltage sources that guarantee reliable electrical isolation from

mains power in accordance with IEC60204-1/EN60204-1.

1. Switch off the operating voltage.

2. Connect the connecting cable to the higher-level controller.

SMAT-8M-UE-0.3-M8D SMAT-8M-UE-2.5-OE

WH2

+24 V

0 V

M8x1, 4-pin, max. tightening torque: 0.3Nm

Tab. 2: Circuit diagram and pin allocation

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	SMAT-8M-U-E-2,5-OE

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo SMAT-8M-U-E-2,5-OE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM E43416 Manual

2 Januar 2026

Pyle PCRMP2DY Manual

2 Januar 2026

Testboy TV 285 Manual

2 Januar 2026

Pioneer 2AM700 Manual

2 Januar 2026

Ruvati RVH7419 Manual

2 Januar 2026

Vaxcel T0703 Manual

2 Januar 2026

Govee H1167 Manual

2 Januar 2026

Ruvati RVH9733 Manual

2 Januar 2026

Sonnenkönig Slim E 1000 Manual

2 Januar 2026

Asus Prime AP202 Manual

2 Januar 2026