Festo VOVK-BT6-M32C-MN-5H5ZP-B3.2F Manual

Festo Ikke kategoriseret VOVK-BT6-M32C-MN-5H5ZP-B3.2F

Læs gratis den danske manual til Festo VOVK-BT6-M32C-MN-5H5ZP-B3.2F (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Festo VOVK-BT6-M32C-MN-5H5ZP-B3.2F, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

VOVK miniature solenoid valve

†‡

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347

-0

www.festo.com

Assembly Instruction s

8149389

2020

- 11a

[8149390]

Miniature switching valve VOVKsolenoid ......................................... English

1 Other applicable documents

All documents for the product are available at

 www.festo.com/sp

2 Safety

2.1 S afety instructions

- Switch off the power supply before carrying out any assembly work.

- Switch off the media supply before carrying out any assembly work.

- Only mount product on components that are in a safe condition.

- Only use the product in its original condition without unauthorized

modifications.

- The product must not be used if the product is dirty or damaged as a

result of damaged packaging.

- Assembly and installation by qualified personnel only.

2.2 Intended Use

The valves are solenoid switching valves for air and are intended to release,

block or change the flow of air.

2.3 Foreseeable Misuse

- The product may not be used outside the limits of the product defined

by the technical data.

- The product must not be used in a potentially explosive atmosphere.

- The product cannot be used for oxygen or aggressive gases

- The product cannot be used for liquids

3 Scope of Delivery

Each VOVK valve comes with a set of mounting plates and screws:

- 2 mounting plates for ends

- 2 screws

The VOVK-…-FB type ( flange mount) comes with one additional plate:

- 1 mounting plate for intermediate position

For the VOVK valves with cable/connector also the 30cm cable is always

included with the valve.

4 Assembly

Assembly and installation by qualified personnel only.

- Switch off the power supply before carrying out any assembly work.

- Switch off the media supply before carrying out any assembly work.

4.1 VOVK-…-FB type (flange mount)

This type of VOVK valve has the flange connection at the bottom and fits to

the manifold for a single valve or for 10 valves.

D 10- -epending on the position of the valve on the valve manifold you will

n eed the mounting plates for end and/or intermediate position.

For 1 valve

1. Put the valve on the base, attach mounting plates for ends.

2. Tighten the screws provided to a tightening torque of 17.6 Ncm

[1.558 in･lbf].

Note: Tighten the screws evenly so the valve does not tilt.

For multiple valves that are lined up

1. Line up the valves on the base, attach the mounting plates for

intermediate positions and for ends.

2. Tighten the screws provided to a tightening torque of 17.6 Ncm

[1.558 in･lbf].

Note: Use the valves in a line at a 6 mm [0.236 in] pitch.

The mounting plates provided (intermediate) are for a 6 mm [0.236 in] pitch.

4.2 VOVK-…- B3F/B3.2F (single valves)

This type of VOVK valve has the direct barb connections.

You will need the two mounting plates for the ends and the screws to mount

them in a similar way as the VOVK-...-FB type above.

4.3 VOVK-…-FF type (stackable manifold)

The VOVK-…-FF type has the flange connection at the front side for stackable

mounting .. of 1 20 valves. The manifold can be assembled by using the set of

end blocks together with a manifold set with the valve bases.

8122790 C12 -VABS -6-S

1x set End blocks for one manifold,

for 6mm OD tubing

8122792 C12 B3 -VABS -6-S- Manifold bl. set with 1 valve base,

type – 3.2mm for 3mm OD tubing

8122791 C12 -VABS -6-S- B4 Manifold bl. set with 1 valve base,

type – 4mm for 4mm OD tubing

A clip is used as connection fitting to clamp the valve bases and end blocks

together.

After assembling the manifold, you can mount the valves:

Attaching valves

1. Confirm that the cover ①

①

①① is in upper position, and the fixing bracket

②

②② is pulled out.

2. Confirm that the gasket is on the valve and insert the valve in the

base.

3. Push in the fixing bracket .

②

②②

4. Slide the cover

①

①① down until it clicks to lock the fixing bracket.

Check to make sure that the fixing bracket is firmly holding the valve

before supplying air to the manifold.

Removing valves

1. Slide the cover ①

①

①① in the direction of the arrow (up).

2. Use a miniature flathead screwdriver or other thin object to pull out

the fixing bracket

②

②②.

3. Pull the valve ③

③

③③ upward.

Note: If you cannot pull the valve out, the fixing bracket was not pulled out

completely in step two.

Do not pull the valve out by force, pull the fixing bracket out again.

Adding manifolds

1. Use the manifold only for up to 20 valves (within one end block set).

2. Remove the connection fitting from between the stations where you

want to add manifolds.

For example, if you want to add a manifold to the end station, remove

the connection fitting from between the end station and the end block.

Note: When removing the fitting, move it forward and backward little

by little to remove it.

3. If you pull it off in one pull, you may bend the fitting or damage the

base.

4. Attach the valve base assembly in the position you want to add.

Note: Before assembly, confirm there are no foreign debris in the

assembly. If dirt or foreign debris are present, it may result in air

leakage.

5. Lightly press on both sides so there is no gap at the base, then align

the connection fitting with the groove in the base and insert it. Press

the connection fitting in until it is even with, or below, the surface of

the base.

Cutout dimensions in mounting surface for base piping

- Drill and tap M3 threads on mounting surface for base piping.

- If you drill a through hole and use a nut, it may interfere with the tubes.

- When you are using washers on the mounting screws, use only ISO small

round washers (outer diameter φ6 [0.236]).

- Tighten the manifold mounting screws to a tightening torque of 49.0 N･cm

[4.337 in･lbf].

- The 10 mm [0.394 in] dimension in the diagram below is the maximum

dimension. If the user wants to set smaller dimensions for the cutout, refer

to the outside diameter of the tube connectors below and set the

dimensions so there is no interference with the piping.

- *There is no problem if the corners shown in the cutout dimensions are

rounded during the cutting work.

- Air supply/exhaust port tube connector outer diameter: φ7 [0.276] (for

tube 6)

- Output port tube connector outer diameter: φ5 [0.197] (for tube 4)

1 / P

3 / R

2 / A

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	VOVK-BT6-M32C-MN-5H5ZP-B3.2F

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo VOVK-BT6-M32C-MN-5H5ZP-B3.2F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025