Festo VTOI-A-V8-30D3-U14-08-V-S015-1 Manual

Festo Ikke kategoriseret VTOI-A-V8-30D3-U14-08-V-S015-1

Læs gratis den danske manual til Festo VTOI-A-V8-30D3-U14-08-V-S015-1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Festo VTOI-A-V8-30D3-U14-08-V-S015-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

VTOI(-A)-V8

Dispense head

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Operating instruction

8186082

2022-12b

[8186084]

8186082

Translation of the original instructions

Applicable documents

All available documents for the product

www.festo.com/sp.

Document Product Table of contents

Assembly instructions Clamping component S-17975 –

Application note – Application examples

Tab. 1

2 Safety

2.1

Safety instructions

2.1.1 General safety instructions

–

Only use the product in its original condition without unauthorised modifica-

tions.

–

Only use the product if it is in perfect technical condition.

–

Before working on the product: switch off the power supply and medium supply

and secure it against being switched on again.

–

Do not subject the product to mechanical stress.

–The product can become hot during continuous operation. Provide protective

measures for use and handling of the product.

–

Do not operate the product in the vicinity of easily flammable liquids and

materials.

–

Do not exceed the maximum permissible pressure of the medium. Potential

pressure peaks in the system must also be taken into account.

2.1.2

Media

–Media may escape in the event of leakage. Take suitable protective measures

when using and handling the product.

–When using crystallising media, plan appropriate rinsing routines for the

product.

–Use only media that will not cause dangerous reactions if mixed.

–Use only media to which the materials used for the product are resistant.

Materials in contact with the medium

10 Technical data.

2.1.3

Return to Festo

Hazardous substances can endanger the health and safety of personnel and

cause damage to the environment. To prevent hazards, the product should only be

returned if explicitly requested by Festo.

–Consult your regional Festo contact.

–

Complete the declaration of contamination and attach it to the outside of the

packaging.

–

Comply with all legal requirements for the handling of hazardous substances

and the transport of dangerous goods.

2.2

Intended use

–The dispense head is intended for installation in laboratory devices.

–

The dispense head dispenses and aspirates fluid media.

2.3 Foreseeable misuse

–The dispense head is not approved for direct contact with foods.

2.4

Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can

evaluate the work and detect dangers. The qualified personnel have knowledge

and experience in handling electrical and fluidic systems.

3 Additional information

–

If you have any questions about planned areas of application of the product,

contact your regional Festo contact person

www.festo.com.

–

Accessories

www.festo.com/catalogue.

4 Product Range Overview

4.1 Scope of delivery

Fig.1

Dispense head(1x)

VTOI-V8...

–dispense

VTOI-A-V8...

–dispense

–aspirate

Clamping component(1x)

4.2

Not in scope of delivery

Fig.2

Screw(2x)

Washer(2x)

5 Mounting

Fig.3

Place the dispense head on a flat surface.1

Position washers at the drill holes .4 5

Tighten screws . Tightening torque: 0.5 Nm ± 10%3

Installation

6.1 Electrical installation

WARNING

Risk of Injury due to Electric Shock.

• For the electric power supply, use only PELV circuits that ensure a reliable

electric disconnection from the mains network.

•

Observe IEC60204-1/EN60204-1.

• The unit must be powered by a power source that fulfils the requirements of an

energy-limited circuit in accordance with IEC61010-1/EN61010-1.

Fig.4

• Connect wire ends . Polarity optional.6

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	VTOI-A-V8-30D3-U14-08-V-S015-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo VTOI-A-V8-30D3-U14-08-V-S015-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025