Finder 1T.41 Manual

Finder Termostat 1T.41

Læs gratis den danske manual til Finder 1T.41 (1 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Finder 1T.41, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

fig.4

fig.3

fig.1

fig.2

fig.5

73.3 mm

22 mm

110 mm

(ﬁg.5/a) (ﬁg.5/b)

1 2 1 2

(ﬁg.5/c)

www.findernet.com

88.8

fig.6 (fig.6/a)

1T.41

ITALIANO

ENGLISH

FRANCAIS

ESPAÑOL

ROMÂNĂ

PORTUGUÊS

IB1T41 - 07/13

ENGLISH

THERMOSTAT LEGEND fig.1( )

A Display

B Graduated knob ON/OFF

C SUMMER/WINTER select push-button

D DAY/ NIGHT selector switch

E Battery Compartment

DISPLAY LEGEND fig.2( )

A Heater ON

BAir-conditioning ON

C Set temperature, actual temperature, low battery

D SUMMER setting active

E WINTER setting active

TECHNICAL DATA

Power supply: 2 alkaline batteries 1.5V AAA

Adjustment range- heating: 8-30°C (5-27°C with night selector ON)

Adjustment range- cooling: 8-30°C (11-33°C with night selector ON)

Display resolution: 0.1°C

Display range: 0-50°C

Precision: +/– 0.5°C at 20°C

Temperature differential: 0.3°C

Sensing element: NTC

Degree of protection: IP20

Output: relay contact

Rating: 5A 250V AC

Mounting: wall mounted

INSTALLATION AND CONNECTIONS

SAFETY REQUIREMENTS: before installing this thermostat, ensure that the supply voltage

to the electrical load (heater, pump, etc.) is not connected and that the load is within the

ratings shown inside the thermostat.

POSITIONING: install the programmable thermostat away from sources of heat (heaters,

direct sunlight, kitchens) and from doors/windows, at a height of about 1.5 m above the floor.

INSTALLATION

- Open the thermostat by pressing the pin on the left side of the device ( )fig.3

- Fix the base to the wall

- Connect the load to the terminals following the wiring diagram (cable Ø 2.5 mm

2) ( )fig.4

- Replace the cover to close the thermostat

ELECTRICAL CONNECTIONS fig.(4)

U= load

C= common terminal

NO = normally open terminal

NC = normally closed terminal

SUMMER/WINTER SETTING

The thermostat can be used for “summer” or “winter” operation, depending on whether it

is connected to an air-conditioner or to a heater.

Press the button ( ) to change from SUMMER to WINTER setting, or vice versa.C - fig.1

DAY/NIGHT SETTING

Move the selector ( ) to change from DAY to NIGHT setting and vice versa. D - fig.1

Under NIGHT and WINTER setting, the temperature is automatically setback (lower) by 3°C

from the DAY temperature as set by the graduated knob (B - fig.1) (Under NIGHT and

SUMMER setting the temperature will be 3°C higher than the temperature as set by knob

B - fig.1).

For a brief time the display will show the set temperature, decreased (or increased) by 3°C.

THERMOSTAT START-UP/SWITCHING OFF

Turn the graduated knob (B - fig.1) to the right, to switch-ON the thermostat and to set the

temperature as shown on the display. Turn the graduated knob ( ) fully to the leftB - fig.1

(until a click is heard) to switch the thermostat OFF, when the display will show OFF.

SETTING THE TEMPERATURES

After having set either SUMMER or WINTER and having set DAY, turn the graduated knob

(B - fig.1) to the desired temperature, as showed on the display.

Note: by following the instructions below it is possible to mechanically block the graduated

knob to restrict the set temperature range within specific limits ( ):fig.5

- Open the thermostat by pressing the pin on the left side of the device ( ) fig.3

- With the knob set to 30°C, remove the tappets 1, 2 and 3 ( )fig.5/a

- Rotate the knob to reveal a series of holes, and insert 2 tappets appropriate to the required

upper and lower limits. Each hole corresponds to 1°C ( )fig.5/b

- Turn the graduated knob such that the third tappet can be inserted in the position shown,

ensuring it is between tappets 1 and 2 ( )fig.5/c

- Replace the cover to close the thermostat

FROST PROTECTION OPERATION

The frost protection is always ON (under WINTER setting).

BATTERY fig.6( )

Power supply: 2 alkaline batteries 1.5 V AAA.

When the batteries are low, the display shows the word "bat" and the temperature,

displayed alternately ( ); fig.6/a

When the batteries are completely discharged, the display will show

only the word "bat". For changing the batteries, see . fig.6

Please dispose of the worn out batteries according to prevailing regulations.

Produkt Specifikationer

Mærke:	Finder
Kategori:	Termostat
Model:	1T.41

Har du brug for hjælp?

Hvis du har brug for hjælp til Finder 1T.41 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Finder Manualer

Finder 1T.T1 Manual

4 Juli 2025

Finder Bliss Wi-fi 1C.91 Manual

28 August 2024

Finder Bliss T 1T.9 Manual

28 August 2024

Finder 1C.51 Manual

2 August 2024

Finder 1T.31 Manual

24 Juli 2024

Finder 1C.71-7 Manual

8 November 2022

Finder 1C.81 Manual

7 November 2022

Finder 1T.41 Manual

28 Oktober 2022

Termostat Manualer

Nyeste Termostat Manualer

Fantini Cosmi Intellicomfort CH141AK Manual

16 December 2025

Fantini Cosmi Intellicomfort CH141E Manual

16 December 2025

Essentials MATRIX Manual

2 December 2025

Honeywell CT62B Manual

1 December 2025

Honeywell X2P RTH20B Manual

28 November 2025

Honeywell RTH2CWF Manual

27 November 2025

Honeywell CT60A1036 Manual

27 November 2025

Honeywell RLV4300A1005 Manual

27 November 2025

Honeywell RTH11B Manual

27 November 2025

Honeywell RLV210A1002 Manual

27 November 2025