Fishman Rare Earth Banjo Pickup Manual

Fishman Ikke kategoriseret Rare Earth Banjo Pickup

Læs gratis den danske manual til Fishman Rare Earth Banjo Pickup (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Fishman Rare Earth Banjo Pickup, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Thank you choosing the Rare Earth™ Banjo Pickup. It is our wish that you are

completely satisfied with this product. If you have any questions or comments, we

would like to hear from you. You may reach our customer service department at 978-

988-9665 or tech@fishman.com

With key input (and ears) from several top players, we spent over a year refining and

dialing in this pickup's performance until we were confident that we got it right.

To achieve noise-free, microphone-like reproduction, this pickup takes full advantage

of cutting-edge active transducer technology borrowed from our acclaimed Rare

Earth™ magnetic soundhole acoustic guitar pickups.

Like its guitar-pickup cousin, this new banjo pickup features a quiet humbucking coil

design that dutifully rejects noise and hum. A powerful neodymium magnet focuses

the banjo's sound through a small steel shim that attaches to the head (not the

player's head, the banjo’s). Hidden in the pickup's case is a stealthy preamplifier,

which strengthens the signal and preserves the natural sound of the instrument. The

pickup can mount on either dual or single coordinator rod banjos (single rod

instruments require a special fitting). With a battery life of well over 5,000 hours, you

can expect years of use between battery changes.

Parts List

Banjo Pickup

Jack Assembly with:

• Switchjack™

• Curved Bracket

• 3/8" Nut

• 3/8" Dress Washer

• 15/23" Dress Washer

• Plastic Spacer for Jack

• 2 Plastic Spacers

• 2 Off-center Washers

• 2 Flat Washers

• 2 10-32 x 3/4" Screws

• 2 Locknuts

• Blue Steel Shim

(sensing element)

Tools Required

• 1/8" Hex Wrench

• 3/8" Wrench

• 1/2” Wrench

• Soldering Iron

Note: If yo u do not fe e l co nfident wi th a

soldering iron, please have the pickup installed

by a professional repair person.

Specifications

Pickup Coil: Stacked Humbucking

Preamp: Low Noise, Discrete,

0 Feedback Circuit

Nominal Output: -10dBu

Noise: -94dBu, A Weighted

Output Impedance: 3k Ohm

Minimum Recommended Load Impedance:

>10 k Ohm

Power: 9 V Alkaline Battery

Battery Life: Over 5000 Hours

The FISHMAN RARE EARTH™ BANJO PICKUP is warranted to function for a

period of One (1) Year from the date of purchase. If the unit fails to function

properly within the warranty period, free repair and the option of replacement or

refund in the event that FISHMAN is unable to make repair are FISHMAN’s only

obligations. This warranty does not cover any consequential damages or damage to

the unit due to misuse, accident, or neglect. FISHMAN retains the right to make

such determination on the basis of factory inspection. Products returned to

FISHMAN for repair or replacement must be shipped in accordance with the Return

Policy, as follows. This warranty remains valid only if repairs are performed by

FISHMAN. This warranty gives you specific legal rights and you may also have other

rights which may vary from state to state.

RETURN POLICY

To retur n products to FISHMAN TRANSDUCERS, you must follow these steps...

1. Call FISHMAN TRANSDUCERS at 978-988-9199 for a Return Authorization

Number (“RAN”).

2. Enclose a copy of the original Bill of Sale as evidence of the date of purchase,

with the product in its original packaging and a protective carton or mailer.

3. FISHMAN TRANSDUCERS’ technicians will determine whether the item is

covered by warranty or if it instead has been damaged by improper customer

installation or other causes not related to defects in material or workmanship.

4. Warranty repairs or replacements will be sent automatically free of charge.

5. If FISHMAN TRANSDUCERS determines the item is not covered by warranty, we

will notify you of the repair or replacement cost and wait for your authorization to

proceed.

FISHMAN TRANSDUCERS

340-D Fordham Road Wilmington MA 01887 USA

Phone 978-988-9199 • Fax 978-988-0770

www.fishman.com

009-035-002 • 8-01

Li mi t ed

Li mi t ed W

Wa rr a nt y

a rr a nt y

Ins t al l at i on Gu id e

fo r C o o r

o r C o o rd i n a to r

d i n at o r-r

-r od Ban jos

o d Ban j os

A C T I V E M A G N E T I C B A N J O P I C K U P

Ra r e Ea r

Ra r e Ea r th ™ Ba n j o

th ™ Ba n j o

Remove the shielding barrel from the jack, run the wire through it, then solder:

• Red wire to tip (shortest terminal)

• White wire to switch (longest terminal)

• Shield to ground (hooked terminal)

Attach a 9 Volt Alkaline battery to the battery clip.

Slip the battery into the holder on the backside of the pickup.

Plug It In

Once everything is buttoned up, plug in the banjo and if necessary, adjust the position of

the pickup along the rods for best sound. Make sure the pickup is spaced 1/16" from the

underside of the head. Very small adjustments will make noticeable changes. Experiment

until you find the Sweet Spot - the loudest and clearest position.

Adapter for Banjos with a Single Coordinator Rod

Two adapter blocks can be made to fit the pickup to a banjo with a single coordinator rod. A hard wood

such as maple is suitable for the blocks.

A split block can be made by first drilling a hole one drill size larger than the diameter of the

coordinator rod through one of the blocks. Trim the block as thin as possible on the pickup side to

minimize offset, and cut in half as per the illustration.

To provide friction between the clamping surfaces

and the rod, take a fine grit open mesh sanding

sheet and wrap it around the rod's circumference.

Fit the split block around the sanding sheet. If

sanding sheet isn't available, glue pieces of 220

grit sandpaper to the drilled surfaces of the block,

and fit it around the coordinator rods.

Now cut a solid block, equal in width to the split block

fitted in place. This will fit in the other half of the clamp

assembly. Note that the rubber strips should be

removed from the inside of the clamps when fitting the

pickup in this manner. There will now be a small offset

between the ideal center of the pickup and the center of

the middle foot of the bridge, but the pickup should

still function prop erly. Follow the rest of the

instructions for pickup installation.

Re-assemble the jack assembly. Wind the pickup wire several times around the

coordinator rod, then route the wire through an opening in the flange.

Solder the Wire to the Jack

BANJO HEAD

FLANGE

CURVED BRACKET

Mount the Pickup

Remove the backing paper from the small rectangular blue shim to expose the

sticky-back adhesive. Attach the shim to the head (inside the instrument) so that the

shim is centered under the coordinator rods, perpendicular to the rods and about

1/2" (12.7 mm) from the edge of the middle bridge foot.

Loosen the wing nut and position the pickup directly over the blue shim. The

magnet will self-locate the pickup over the shim. For a darker response, leave the

pickup positioned directly over the shim. For brighter response, move the pickup

1/4" away from the shim, towards the neck.

Set the pickup about 1/16" from the surface of the head. You can make a 1/16"

spacer cut from the box for this pickup and use it to set the gap between the head

and the face of the pickup.

After the pickup is secured to the coordinator rods, disassemble the jack then attach

the curved bracket to the flange. To accommodate different styles of flanges, we

provide two types of washers (a set of standard and off-center washers).

Ra r e Ea r

Ra r e Ea r th ™ Ba n j o

th ™ Ba n j o

Ra r e Ea r

Ra r e Ea r th ™ Ba n j o

th ™ Ba n j o

Ra r e Ea r

Ra r e Ea r th ™ Ba n j o

th ™ Ba n j o

1 - Screws

2 - Plastic Spacers

3 - Off-Center Washers

4 - #10 Washers

5 - Locknuts

BRIDGE FEET

BLUE SHIM

TAILPIECE

NECK

1/2"

RODS

2 3 54 61

Negative Battery Wire

(white) to Switch

Shield to

Sleeve

Pickup Signal

(red) to Tip

1 - 15/32”Dress Nut

2 - 15/32”Dress Washer

3 - Plastic Spacer

4 - Curved Bracket

5 - 3/8”Dress Washer

6 - 3/8”Dress Nut

CENTER

OFFSET

SOLID

BLOCK

COORDINATOR

ROD

SANDPAPER

SPLIT

BLOCK

BODY OF

PICKUP

Produkt Specifikationer

Mærke:	Fishman
Kategori:	Ikke kategoriseret
Model:	Rare Earth Banjo Pickup

Har du brug for hjælp?

Hvis du har brug for hjælp til Fishman Rare Earth Banjo Pickup stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fishman Manualer

Fishman Rare Earth Banjo Pickup Manual

21 August 2024

Fishman TriplePlay Manual

20 August 2024

Fishman Rare Earth Soundhole Pickups Manual

20 August 2024

Fishman Neo-D Manual

20 August 2024

Fishman Neo-Buster Manual

19 August 2024

Fishman Universal Battery Pack Manual

17 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rowenta Thermostyle SF712L Manual

13 August 2025

American Audio CPX 10A Manual

13 August 2025

Bluetti Elite 100 V2 Manual

13 August 2025

American Audio Topaz EX Manual

13 August 2025

American Audio Accu Fog 1000 Manual

13 August 2025

Optimate Solar Duo Manual

13 August 2025

American Audio Micro Wash WWCW Manual

13 August 2025

Adj UC3 Foot Controller Manual

13 August 2025

Adj WiFLY D6 Branch Manual

13 August 2025

Rowenta Magic Nature CF7826 Manual

13 August 2025