Fluke BC7217 Manual

Fluke Accu BC7217

Læs gratis den danske manual til Fluke BC7217 (2 sider) i kategorien Accu. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Fluke BC7217, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PN 691862

September 1998 Rev.1, 3/09

All product names are trademarks of their respective companies.

In Case of Difficulty

For service help or to contact Fluke for any reason, call one of

the following telephone numbers:

USA and Canada: 1-888-99-FLUKE (1-888-993-5853)

Europe: +31 402-678-200

Japan: +81-3-3434-0181

Singapore: +65-*-276-6196

Anywhere in the world: +1-425-356-5500

Or, visit Fluke's Web site at . www.fluke.com

LIMITED WARRANTY & LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship

for one year from the date of purchase. This warranty does not cover

fuses, disposable batteries or damage from accident, neglect, misuse or

abnormal conditions of operation or handling. Resellers are not

authorized to extend any other warranty on Fluke’s behalf. To obtain

service during the warranty period, send your defective tester to the

nearest Fluke Authorized Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an implied

warranty or of incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett WA

98206-9090

Fluke Europe B.V.

P.O. Box 1186

5602 B.D. Eindhoven

The Netherlands

BC7217-120

BC7217-INTL

Battery Chargers

Instruction Sheet

Introduction

The Fluke BC7217 Battery Charger charges Fluke BP72XX

series Nickel-Cadmium and Nickel-Metal-Hydride battery packs

for handheld test tools. The BC7217 consists of a charger base

and a power supply.

Connecting the Charger to Line Power

Model BC7217-120, Model BC7217-INTL

Connect the wall adapter to line power within the following range:

90 to 264V ac, 47 to 63 Hz. Plug the barrel connector into the

charger dc input jack as shown in Figure 1.

zq1f.eps

Figure 1. Connecting the Charger to Line Power

Charging the Battery

Note

Sometimes a new battery needs several

charge/discharge cycles before it performs to full

capacity.

Before you use a new battery for the first time, charge it fully.

Connect the charger to line power and place the battery in the

charger as shown in Figure 2. You can leave the battery pack on

trickle-charge indefinitely without damage. The charger will not

overcharge a battery, even if you reinsert a charged battery.

• Nickel-Cadmium Battery

To obtain a full charge, charge the battery until the indicator

blinks (approximately 1-1/2 hours).

• Nickel-Metal Hydride Battery

To obtain a full charge, charge the battery until the indicator

blinks (approximately 2-1/2 hours), then leave it in the charger 3

more hours for a full charge.

Note

When you remove a charged battery from the charger,

wait for the blinking indicator to go off before you insert

a discharged battery. It takes about 2 seconds for the

battery charger to reset.

zq2f.eps

Figure 2. Inserting the Battery

When to Charge

Wait until the battery is fully discharged before you charge the

battery. The battery will retain its charge longer.

Charge Mode Indicator

The red indicator light on the side of the charger shows the status

of the battery charge cycle as follows:

• Off

The battery is not inserted, or it is inserted incorrectly, power is

disconnected or not available, or the internal fuse is blown.

• Steady on

High-current fast charge mode.

• Blinking (50% duty cycle)

Nickel-Cadmium battery: trickle-charge mode.

Nickel-Metal Hydride battery: pulsed charge for the first 3 hours

after blinking starts, then trickle-charge mode.

• Blinking (less than 50% duty cycle)

Pre-charge delay for proper battery temperature or voltage

conditions.

Internal Fuse

An internal fuse is soldered in place. If the charger indicator does

not go on when a battery is installed, this fuse may be blown. The

fuse cannot be replaced by the user.

Specifications

BC7217-120, BC-7217-INTL:

Wall Adapter: Input Voltage: 90 to 264 V ac

Input Voltage Frequency: 47 to 63 Hz

Output Voltage: 15 V dc, 2 A

Line power adapters: North America/Japan,

Europe, UK, Australia

Safety Approvals: UL, CSA and TUV

Both Models:

Charger Input Voltage: 14 to 20 V dc

DC Power Plug Polarity:

– Ring egati eN v

+ Center Positi ev

Temperature: Operating: 0 to 40 °C

Storage: -20 to 70 °C

Humidity (noncondensing):

Operating: 0 to 90% R.H.

Storage: 5 to 95% R.H.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Accu
Model:	BC7217

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke BC7217 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Accu Fluke Manualer

7 Oktober 2024

30 Juli 2024

28 Juli 2024

24 Juli 2024

Accu Manualer

Nyeste Accu Manualer

Stiga E 24 Manual

20 Februar 2025

Stiga E 22 Manual

20 Februar 2025

Aim TTi PL303 Manual

31 Januar 2025

Vonroc CD829AA Manual

9 Januar 2025

Biltema 80-839 Manual

2 Januar 2025

JVC BN-VC2128 Manual

31 December 2025

DJI FPV Intelligent Flight Battery Manual

30 December 2025

Tripp Lite PV4IN1 Manual

30 December 2025

Stiga E 450 Manual

29 December 2024

Kress KAB08 Manual

29 December 2024