Friedland Evo Wirefree 200m - D412 Manual

Friedland Dørklokke Evo Wirefree 200m - D412

Læs gratis den danske manual til Friedland Evo Wirefree 200m - D412 (1 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Friedland Evo Wirefree 200m - D412, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Evo Wirefree 200m* Chime Kit with Light

Instructions –

Please retain these instructions for future reference

Pack contents:

Portable Door Chime with Light

Bell push & CR2032 Lithium coin cell battery

Adhesive pad,2xscrews(ø3xm)2xwallplugs (ø5 x 25mm)

for mounting the bell push

Fig. 6

Fig. 7

7. Programming a second push

Within 5 minutes of pressing the first push, press the second

push

until the chime sounds, then use button B to change the tune

if required.

If more than 5 minutes has elapsed since the first push was

programmed, press and hold both buttons A and B until the chime

sounds, this takes approx 5 seconds. The chime is now cleared

and can programmed to one or two door pushes

All EVO and Décor Chimes and Bell Pushes use programming

to ensure no interaction from other neighbouring systems.

8. Sound Selection

A = Main push sound selection

B = Second push sound selection

Chime tune options are as follows:

1. Big Ben 2 Note (Default Tune for 1st Push)

2. Mini Bell 4 Note w/ Echo (Default Tune for 2nd Push)

3. Clarinet

4. Altosax

9. Flashing Light and sound controls

The settings are:

0. Sound only

1. Sound with flashing light

2. Flashing light only

Flashing Light and sound control

To turn the door chime sound off or to stop

the flashing LED light when the bell push

is pressed, turn knob C

Note: when the chime is being programmed

this control will not function for 5 minutes.

Trouble Shooting

Chime not Sounding

Batteries may not be inserted correctly

Check all batteries have been inserted correctly

Chime may be positioned out of range of the bell push

Move your chime closer to the bell push

Note:

During the programming cycle the transmission range may be reduced

The chime will resume optimum range after 5 minutes

A metallic object may be blocking the signal from bell push position

Experiment with the location of the chime to see if you can move it in a

more suitable place

The battery in the bell push may need replacing

Press the bell push. If the confidence light (D) flashes 5 times after

being pushed, replace the battery

Note: In cold conditions, poor location or environment, operating at

maximum range it is advisable to replace the battery more frequently

before the indicator light flashes

(i.e every 12 - 18 months) to maintain optimum performance

Your bell push and chime haven't been programmed

Do the automatic programming of your chime and bell push

The Selection knob may have been set incorrectly

Do position of knob C as described in section 8 above

LED flashing light does not flash

The selection knob is not set correctly, reset position of knob C as

described in section 8 above

LED light

Declaration

Novar ED&S hereby declares that this wirefree product is in compliance with

the essential requirements and other relevant provisions of the Radio and

Telecommunications Terminal Equipment ( R & TTE ) directive, 1999/5/EC

Fig. 8

Friedland guarantees this product for 3 years from date of purchase.

Proof of purchase is required, this does not affect your statutory rights.

If you require further information about our products, call the Friedland helpline

on 01268 563066.

Friedland, The Arnold Centre, Paycocke Road, Basildon, Essex, SS14 3EA, England

www.friedland.co.uk

Fig. 1

Fig. 2

Novar ED&S h

the essential

Telecommuni

8. Sound Se

A = Main pus

B = Second p

Chime tune o

1. Mini Bell 2

2. Mini Bell 1

3. Flugel Hor

Friedland guaran

Proof of purchas

If you require fur

on 01268 56306

Friedland, The A

www.friedl

Fig. 3

Fig. 4

Trouble Sh

Chime not S

Batteries m

Check all ba

Chime may

Move your c

Note: During

be reduced.

The chime w

A metallic ob

Experiment w

in a more su

The battery

Press the be

being pushe

Note: In cold

maximum ra

frequently be

(i.e every 12

Your bell pu

Do the autom

All EVO a

to ens

You will require:

3 X LR6 (AA) Alkaline batteries for the Door Chime

Only long-life Alkaline batteries must be used

A small crosshead and flathead screwdriver, a ø5mm. masonry drill

Installation

*Please note: The stated range of this product is measured in open

field conditions. Walls, ceilings and the positioning the bell push or

door chime on or near metal structures or reinforced PVC doors or

doorframes will reduce the transmission range.

1. Open the bell push

To open the front cover carefully

insert a flat bladed screw driver, into

the slot and twist gently (A). When

refitting the front cover to ensure the

weather proofing is maintained,

always mount the bell push in the

upright position and replace the

cover securely. Fig. 1

2. To fit or replace the battery

Open the front cover and

insert the CR 2032 Lithium

coin cell battery into the cover

as shown in Fig. 2.

3. Mount the bell push

Ensure the wall surface is clean and dry.

Mount using either the double sided

sticky pad on a smooth surface, or the

screws and wall plugs provided, See Fig 3.

Do not mount the push on or near (< 30cm)

large metal objects, as it will block signals

from the push. Next, hook the cover at

the top, then press down at the bottom to

clip in place.

4. Test the bell push

When the bell push button is pressed,

the confidence light (B)

in Fig. 4, will

illuminate to reassure the caller that

the bell push is

working.

The light will flash 5 times when

the battery needs replacing

5. Fit the Door chime batteries

Remove battery compartment cover and insert three LR6 (AA)

alkaline batteries as shown in Fig. 8.

The first time a chime unit is powered up, the sounds available

are demonstrated.

6. Automatic Programming of bell pushes

First, place the chime close to the door push (within 8m/ 25ft)

to program the chime and check that it is working.

Press the door push until the chime responds with a tune.

You can leave this tune or change the tune by using button A

(see Fig. 6, sound selection).

10. Replacing Batteries

First remove decorative cover

and replace with three LR6 (AA)

alkaline batteries. (Fig. 8)

When replacing batteries the

chime is still programmed

and can be used straight away.

Produkt Specifikationer

Mærke:	Friedland
Kategori:	Dørklokke
Model:	Evo Wirefree 200m - D412

Har du brug for hjælp?

Hvis du har brug for hjælp til Friedland Evo Wirefree 200m - D412 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Dørklokke Friedland Manualer

Friedland Evo D3200 Manual

30 December 2025

Friedland Evo D3120 Manual

7 December 2024

Friedland D3005S Manual

10 September 2024

Friedland Evo Wirefree 200m - D412 Manual

21 August 2024

Friedland L430N Spectra Plus Manual

21 August 2024

Friedland Evo 100m - D421E Manual

18 August 2024

Friedland D962S Manual

8 August 2024

Friedland EvoHome and Garden Kit - D426E Manual

8 August 2024

Friedland D3200 Manual

7 August 2024

Friedland D359 Manual

6 August 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Extel Carillo Plug Manual

10 November 2025

Nedis WIFICDPC11CBK Manual

3 November 2025

Extel Carillo Plug Flash Manual

1 November 2025

Extel Carillo Manual

31 Oktober 2025

Elektrobock BZ11-21 bílá Manual

5 Oktober 2025

Nexa LMLR-710 Manual

3 Oktober 2025

Nexa MLR-1922 Manual

3 Oktober 2025

Blink Video Doorbell Manual

1 Oktober 2025

DiO 84206 Manual

26 September 2025

DiO 54731 Manual

26 September 2025