Frigidaire FFTA1033Q2 Manual

Frigidaire Aircondition FFTA1033Q2

Læs gratis den danske manual til Frigidaire FFTA1033Q2 (14 sider) i kategorien Aircondition. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Frigidaire FFTA1033Q2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/14
READ BEFORE INSTALLING UNIT
For Through-the-Wall Air Conditioners
Installation Instructions
N
O
TE
:
DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE
Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install Air Conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.
Do This First (for existing sleeve)
You may not need all parts in the kit. Discard unused parts.
Items in Kit
2020213A1639
Hardware
2
2
3
Tapered Spacer Blocks (17” Long)
Plastic Divider ( )
4
Stuffer Seal ( )
4
1
2
3
4
5 ( )seal
1
6 2
7 3
8
No. Qty.
2
9
Centering/Support Blocks ( )”4 x 3 x 1” ”
1
2
1
2
1
2
” ” ” x 4 x 14
1
8
1
2
1
2
1 x 1 x 84” ” ”
1
2
1 x 1 x 25” ” ”
1
2
seal ( )1 x 1 x 14” ” ”
1
2
seal ( )
1 x x 25”3/8” ”
seal ( )1 x x 14”3/8” ”
seal ( )1 x x 14”3/4” ” 2
Hardware
2
1
1
Ground Wire (green)
2
13
10
11
12
14 Grounding Screw
15 1
16 1
17
No. Qty.
4
18
Trim Frame (top & bottom legs)
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer 4
Trim Frame (side legs)
Toothed washer for grounding screw 2
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
INSTALLATION WARNINGS AND CAUTION
2
Installation Instructions
How to Install
1. Identify the wall-sleeve brand for your installation, from the chart below.
Brand Wall Sleeve Dimensions
Width Height Depth
General Electric/Hotpoint 26 15581578
Sears/Kenmore 253416781858
Carrier (51S Series) 1858
1678
2534
Friedrich* 1634
1634
27
Emerson/Fedders* 15
1534
2634
Whirlpool 2578161217 18or 23
Fedders/Emerson* 27 163416 341934
or
White-Westinghouse 2512151416, 17 or 22
12
Frigidaire 2512151416, 17 or 22
12
Carrier (52F Series) 2512151416, 17 or 22
12
C
A
U
TI
O
N
:
When installation is complete, replacement unit MUST have a rearward slope as shown in Fig.1.
2. Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows:
Clean interior (do not disturb seals).
Wall sleeve must be securely fastened in wall before installing Air Conditioner. Drive more nails or screws through
sleeve, into wall, if needed.
Retouch wall sleeve painted surface if needed.
Wall
sleeve
REAR
1/4" to 5/16"
FRONT
LEVEL
UNIT
Fig.1
3. If not existing, drill a 3/16" clearance hole for grounding screw through left side of wall sleeve, in a clear area about
3 inches maximum back from front edge of sleeve, using grounding screw and toothed washer. Pull loose end
of ground wire out front of sleeve, and temporarily bend it down and around lower edge of sleeve (Fig.2). This
ground wire will later be attached to frame of air conditioner once it is installed.
Wall sleeve to unit
sleeve grounding
Max.
Hole
Fig.2
IMP
O
RTAN
T
All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear
grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner.
For new installations, a Frigidaire Sleeve Kit (EA108T) is recommended.
For larger sleeves, an adaptor trim kit (EA120T) is available.

Produkt Specifikationer

Mærke: Frigidaire
Kategori: Aircondition
Model: FFTA1033Q2

Har du brug for hjælp?

Hvis du har brug for hjælp til Frigidaire FFTA1033Q2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Aircondition Frigidaire Manualer

Frigidaire

Frigidaire GHWW125TE1 Manual

9 April 2025
Frigidaire

Frigidaire GHWW105TE1 Manual

9 April 2025
Frigidaire

Frigidaire FHPH142AA1 Manual

9 April 2025
Frigidaire

Frigidaire GHPC142AA1 Manual

9 April 2025
Frigidaire

Frigidaire GHPH142AA1 Manual

9 April 2025
Frigidaire

Frigidaire FFPH1422T1 Manual

6 Oktober 2024
Frigidaire

Frigidaire FHPC082AB1 Manual

6 Oktober 2024
Frigidaire

Frigidaire FFRE1233Q1 Manual

3 Oktober 2024
Frigidaire

Frigidaire FFRA121ZAE Manual

29 September 2024
Frigidaire

Frigidaire FRA126CT1 Manual

23 September 2024

Aircondition Manualer

Nyeste Aircondition Manualer

Eurom

Eurom AC4201 Manual

6 Juli 2025
Eurom

Eurom AC5201 Manual

5 Juli 2025
Eurom

Eurom Airflow LED Cordless Manual

13 Juni 2025
Daikin

Daikin FXNQ63A2VEB Manual

9 April 2025
Daikin

Daikin FXNQ20A2VEB Manual

9 April 2025
Panasonic

Panasonic CS-CU-Z21RKR Manual

9 April 2025
Daikin

Daikin EWWP022KBW1N Manual

9 April 2025
Samsung

Samsung AC060DN4DKG Manual

7 April 2025
Fujitsu

Fujitsu ASHA009HCAH Manual

3 April 2025
Samsung

Samsung AC036MNCDKH Manual

30 Marts 2025