Frigidaire IMKTF20A Manual


Læs gratis den danske manual til Frigidaire IMKTF20A (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Frigidaire IMKTF20A, eller vil du spørge andre brugere om produktet?

Side 1/9
AUTOMATIC ICE MAKER
INSTALLATION INSTRUCTIONS
P/N: A22932801
WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator
from electrical power before connecting a water supply line to the refrigerator.
Connect the ice maker to a potable water supply only.
Ice Maker (IMKTF20A) Kit Components
Tools Needed:
Flat head screw driver Phillips or Quadrex driver
¼" Hex driver Gloves
Drill Needle nose pliers
Plastic putty knife
NOTE
Check with your local building authority for recommendations on water lines and associated materials prior
to installing your new refrigerator. For household water line hookup from the home water supply system to
the unit, we recommend for homes with existing valves Smart Choice® water line kit 5304437642 (with a 6
Stainless Steel Water Line) and for homes without an existing valve, we recommend Smart Choice® water
line kit 5304493869 (with a 6� Polyline Waterline). Please refer to Frigidaire.com for more information.
Water Valve
QTY: 1
IMPORTANT
We recommend an authorized service technician to install the ice maker kit.
Ice Maker
QTY: 1
Ice Container
QTY: 1
Water Inlet Tube Assembly
QTY: 1
Screw (B)
QTY: 2
Screw (A)
QTY: 2
Plastic Clamp
QTY: 3
Ice Maker
Connector Cover
QTY: 1
2
Figure 4
Ice Maker Installation Instructions
1. Unplug the refrigerator from the electrical outlet.
2. Remove the spacer. Remove the freezer shelf
(some models) by pushing the shelf to the left
until the right side of the shelf comes free from
the holes. See Figure 1.
3. Use a plastic putty knife to remove the 2 plugs on
the left wall of the freezer compartment. Discard
the plugs. See Figure 3.
4. Remove the harness connector cover, where the
ice maker will plug in, with aathead screwdriver.
Discard the harness connector cover. See Figure 3.
NOTE
Some models have two plugs on the left freezer wall
that must be removed. These holes will be used to
mount the Ice Maker. (You will also insert the Water
Inlet Tube in the plug on the back wall.)
5. Place two, long, ice maker mounting screws ( ) A
into freezer wall where plugs were removed
in Step 3. Turn each screw clockwise until " ½
remains out. See Figure 4.
NOTE
You will need both hands to hook up and secure
the Ice Maker to the freezer wall. DO NOT let the
Ice Maker dangle free after the wiring harness is
plugged into the connector on the back freezer wall.
7. Place the ice maker harness into the cover.
See Figure 6.
6. Unhook one loop of the ice maker harness.
See Figure 5.
Figure 3
Figure 5
Figure 6
Then slowly lift up and pull the shelf free from the
holes on the right side. See Figure 2.
Figure 1
Figure 2
A


Produkt Specifikationer

Mærke: Frigidaire
Kategori: Ikke kategoriseret
Model: IMKTF20A

Har du brug for hjælp?

Hvis du har brug for hjælp til Frigidaire IMKTF20A stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Frigidaire Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer