Fusion MS-FHM Manual

Fusion Fjernbetjening MS-FHM

Læs gratis den danske manual til Fusion MS-FHM (6 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Fusion MS-FHM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Handheld Microphone

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the guide in the Important Safety and Product Information

stereo box for product warnings and other important information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

CAUTION

To avoid possible personal injury, always wear safety goggles,

ear protection, and a dust mask when drilling, cutting, or

sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface to avoid damaging the vessel.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact Fusion® Product Support.

Tools Needed

• Pencil

• Drill

• 16 mm (5/8 in.) drill bit

• 2.5 mm (3/32 in.) drill bit

• 16 mm (5/8 in.) socket or wrench

• Phillips screwdriver

• Marine sealant (optional)

Installing the Connector Mount

Before drilling a hole to mount the connector, you should verify

that the microphone cable is long enough to reach the back of

the stereo and the connector mounting location.

You can use the included hardware to mount the connector on

the end of the microphone cable onto the dashboard or other

mounting surface.

1Orient the mounting plate with the flat edge of the central

hole pointing to the left, and place it on the surface where

you plan to mount the connector.

If you orient the plate with the flat surface pointing to any

direction other than the left, the microphone cable will not

point downward when you connect it.

2Using the mounting plate as a template, trace the cable

hole in the center of the mounting plate, and mark the screw

locations.

3Set the mounting plate aside.

Do not drill through the mounting plate.

4Using a 16 mm (5/8 in.) drill bit, drill the center cable hole

in the mounting surface.

5Using a 2.5 mm (3/32 in.) drill bit, drill the pilot holes.

6Place the rubber gasket between the mounting plate and

the mounting surface.

7Using the included screws, attach the mounting plate and

gasket to the mounting surface.

8Route the microphone cable to the back of the stereo and to

the connector mount.

9Feed the connector through the back of the mounting

surface.

10Secure the connector and weather cap to the mounting

plate using the nut .

NOTICE

If you disconnect the microphone from the connector, you

should secure the weather cap to avoid corrosion on the

connector contacts.

Mounting the Microphone Hanger

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

You can mount the microphone hanger in a convenient location

near the radio.

1Select a mounting location for the microphone within reach of

the microphone cable.

2Using the microphone hanger as a template, mark the pilot

holes.

3Drill the mounting holes using a 3 mm (1/8 in.) drill bit.

4Secure the microphone hanger to the mounting surface using

the included screws .

GUID-1CD23792-2CC2-4768-B1BD-D1E11B6C23D8 v1June 2020

Connection Diagram

Microphone

connector

You can securely mount the microphone

connector in an accessible location (Installing the

Connector Mount, page 1).

RCA connectors You must connect these to the AUX IN

connector on the stereo wiring harness.

If the stereo has more than one AUX IN

connector, you must connect to the AUX1

connector.

Compatible

stereo

TELEMUTE You must connect the bare wire from the

microphone cable to the TELEMUTE wire on the

stereo wiring harness if you want the microphone

to change the source when activated(Operating

the Handheld Microphone, page 2).

Negative (-)

power

connection

For the best results, you should connect the

negative (-) wire from the microphone to the

same negative (-) terminal as the stereo.

Positive (+)

ignition power

connection

You should connect the positive (+) wire from the

handheld microphone to the ignition wire from

the stereo to avoid draining the battery.

You must route the combined positive (+) and

ignition wires through a 3 A fuse before

connecting to the ignition or manual switch.

Ignition or

manual switch

The ignition or manual switch turns on the stereo

and microphone.

Stereo power

positive

connection

You should not connect the positive (+) wire from

the microphone to the constant power cable from

the stereo to avoid draining the battery.

Power source

Operating the Handheld Microphone

You must configure the stereo before you can operate the

handheld microphone (Configuring the Fusion Stereo for the

Handheld Microphone, page 2).

You can use the handheld microphone from any source on the

stereo. If the source is set to anything other than AUX1 when

you hold the microphone button, the source switches to AUX1

automatically, and switches back to the original source after you

release the button.

NOTE: You should stand behind the speakers that will be

broadcasting from the microphone. If you are standing in front of

the speakers, the microphone will pick up the broadcast and

cause feedback.

1Select any source on the stereo.

NOTE: If you set the stereo to the AUX1 source, there is no

sound until you hold the microphone button and speak.

2Hold the button on the side of the microphone and speak into

it.

NOTE: If the stereo is playing music from a source, you

should wait about 2 seconds before speaking to avoid cutting

off the beginning of your announcement.

3After you have finished speaking, release the button.

If the stereo was playing music from a source before you held

the button, the stereo switches back to that source

automatically.

Configuring the Fusion Stereo for the Handheld

Microphone

1On the stereo, select > > .SETTINGS TELEMUTE

2Select to fill the check box.AUX1

The stereo will now change to the AUX1 source when you

hold the button on the side of the handheld microphone.

3Select > > > .SETTINGS SOURCE AUX1

4Select to clear the checkbox.PARTYBUS ENABLED

When you clear the checkbox, the AUX1 source is no longer

available for streaming over the Fusion PartyBus

™ network. It

is recommended to disable network streaming for the

microphone source to avoid feedback caused by the slight

delay present when streaming.

Adjusting the Gain of the Handheld Microphone

If the volume of the microphone broadcast is too loud or too

quiet in relation to the other sources on the stereo, you can

adjust the gain level for the AUX1 source.

1On the stereo, change the source to .AUX1

2Adjust the gain to raise or lower the microphone volume in

1 db steps.

A positive (+) gain setting increases the microphone volume,

and a negative (-) gain setting decreases the microphone

volume.

Specifications

Microphone dimensions (H×W×D) 88 × 60 × 34 mm (3

1/2 × 23/8 ×

111/32 in.)

Power and audio cable length 60 cm (23

5/8 in.)

Frequency response From 100 Hz to 4 kHz

Microphone weight 250 g (8.75 oz)

Output (max.) 1 Vrms

THD+N (Vo = 1 Vrms, 1 kHz) Less than 0.1% Vrms

Gain +18 ± 0.5 dB

Load impedance (min.) 10k Ohm

Operating voltage From 10.5 to 32 Vdc

Current (at 14.4 Vdc) 0.005 A

Fuse (not included) 3 A

Water rating IEC 60529 IPX7

Garmin®, the Garmin logo, Fusion®, and the Fusion logo, are trademarks of Garmin Ltd.

or its subsidiaries, registered in the USA and other countries. These trademarks may not

be used without the express permission of Garmin.

M/N: A13014

1 For more information, go to .garmin.com/waterrating

Produkt Specifikationer

Mærke:	Fusion
Kategori:	Fjernbetjening
Model:	MS-FHM

Har du brug for hjælp?

Hvis du har brug for hjælp til Fusion MS-FHM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Fusion Manualer

Fusion MS-NRX300 Manual

15 August 2024

Fusion MS-FHM Manual

13 August 2024

Fusion MS-ARX70W Manual

12 August 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Renkforce RF-WRC-300 Manual

14 August 2025

Renkforce RF-PLP-200 Manual

14 August 2025

One For All EazyClean URC 9290 Manual

13 August 2025

One For All URC 2781 Manual

13 August 2025

One For All Digital 5 URC 7557 Manual

12 August 2025

Chamberlain CH382C Manual

12 August 2025

One For All Essence 4 URC 1242 Manual

12 August 2025

One For All Essence 8 URC 1282 Manual

12 August 2025

Chamberlain CHU62C Manual

12 August 2025

One For All Digital Five URC 7555 Manual

12 August 2025