Futaba FP2GS Manual

Futaba Radio kontrol FP2GS

Læs gratis den danske manual til Futaba FP2GS (4 sider) i kategorien Radio kontrol. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Futaba FP2GS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Futaba

DIGITAL PROPORTIONAL

RADIO CONTROLFP-2GS

D60431

SPECIAL FEATURES:

SET CONTENTS AND RATINGS

(Specifications are subject to change without prior notice.)

TRANSMITTER FP-T2GS

• Contemporary

styling with smooth operating gimbals for

superior control.

• 500mW output.

• Battery level

meter indicates the state of the battery

voltage at a glance.

• Built-in antenna.

RECEIVER FP-R102GF

•BEC (Battery Eliminator Circuitry) system allows sharing

of the running Nicd battery and eliminates the need

for a

regulator and diode.

•High performance 2 channel receiver with ASP system

when used with the proper transmitter.

•Crystal

socket

uses

new

type

of highly reliable subminia-

ture pins. Reliability is increased and the crystal can be

changed from the outside.

SERVO FP-S128

SMALL, RUGGED. HIGH NEUTRAL SERVO

•Skew type armature motor.

Movement of the trimmer by even one notch is tracked by

a skew type motor which displays a performance near that

of a

coreless motor.

•New indirect drive potentiometer improves vibration and

shock resistance and neutral accuracy.

•Futaba low-power custom 1C provides extremely high

torque, narrow dead band, and superior tracking.

•Fiberglass reinforced PBT (polybutylene terephthalate)

injection

molded

servo

case

mechanically strong and

invulnerable to glow fuel.

•Strong

polyacetal

resin

ultra-precision

servo

gear

features

smooth operation, positive neutral, and very little backlash.

•Fiberglass reinforced epoxy resin PC board with thru-the-

hole plating improves servo amp vibration and shock resist-

ance.

•Three pin connector eliminates faulty contact and improves

reliability against vibration and shock. Housing has a

reverse insertion prevention mechanism.

•Special grommet simplifies

mounting of the servo and has

an excellent cushioning effect.

•Six special adjustable splined horns.

•High 48.7 oz.in

(3.5kg-cm) maximum output torque allows

use

in almost any model.

Model number

Transmitter

Receiver

Servo

Switch, battery holder, etc.

FP-2GS

FP-T2GSx1

FP-R102GFx1

FP.S128.x2

TRANSMITTER FP-T2GS.

Operating method 2 stick system

Transmitting frequency 27MHz band, 72MHz band

Modulation system AM (amplitude modulation)

Power requirement

12V,

round penlight battery x 8

Receiver FP-R102GF

Receiving frequency

27MHz band, bands 1 to 6

72,75MHz

455kHz

3kHz/-3dB

550 yards (500m) on the ground

when used with FP-T2GS (At the

best radio wave condition of envi-

ronment)

4.8V

8.4V

7.2V/13mA,4.8V/33mA

1.46x

2.19

0.75

(37

55.5

19mm)

1.34

(38g)

Intermediate frequency

Selectivity

Receiving range

Power supply

Current drain

Dimensions

Weight

SERVO FP-S128

Control system

Operating angle

Power requirement

Current drain (IDLE)

Output torque

Operating speed

Dimensions

+pulse width control

One side 45° or more

4.8V-6V

6.0V, 8mA (at idle)

48.7 oz.in. (3.5 kg-cm)

0.24 sec/60°

1.6x0.8x 1.6 in.

(40.5 x 20 x 40.5mm)

1.92oz. (53g)

Weight

HANDLING THE TRANSMITTER

•The name of each part of the transmitter is given in the figure.

Familiarize yourself with their operation.

•Remove the battery cover on the rear of the transmitter as

illustrated in the figure, and insert 8 round penlight batteries,

paying careful attention to their polarity.

•Extend the antenna fully, and set the power switch to the

ON position. The pointer of the level meter should deflect to

the green zone. If it fails to deflect, or deflects slowly, the

polarity of the batteries is incorrect, or the batteries are

faulty.

•Since the range of the radio waves will become short when

the pointer of the level meter deflects to the red zone, re-

place the batteries when the pointer only deflects to the

boundary between the green and red zones.

•The

trim

lever

used

to fine

adjust

each

channel.

Use

it for

neutral adjustment and to correct the flying posture after

the mechanism has been installed. After test flight, operate

with the trim lever in the neutral position, as far as possible,

by correcting with the rod adjuster, etc.

•Since the elevator stick employs a self-neutral system, install

the sliding plate as shown in the figure when changing it to a

ratchet system. Then remove the strong spring attached to

the hook and replace it with the spring supplied as an ac-

cessory.

•When the transmitter is used with a tank, the direction of the

stick can be changed 90 degrees by removing the four rudder

stick mounting screws.

•To change the crystals, loosen the rear cover mounting screws,

remove the rear cover, and then replace the crystal. The

crystal is located at the left side of the printed wiring board.

The transmitter crystal is marked (T) and the receiver crystal

is marked (R). CAUTION: Frequency change has to be done

under the supervision of FCC licensed personnel.

(Engine control

trim)

Elevator trim

Elevator stick

(engine control

stick)

The batteries can be

easily loaded by

inserting them

four at

a time from the back.

Modification from self-neutral

system to ratchet system.

Install sliding plate

Replace with

weak spring

Fig.

Slide in the direction

of the arrow while

pushing here.

Rear cover mounting screws

Fig.

Fig.1

Rudder stick

Rudder

trim

Antenna

Level meter

Power switch

RECEIVER FP-R102GF AND SERVO FP-S128

The BEC mark is displayed on the front of the receiver of BEC (Battery

Eliminator Circuitry) system sets with a receiver with shared power supply

regulator.

Your NEW FUTABA Digital Proportional R/C system is guaran-

teed against defects in workmanship and material for 180 days

from the date of purchase when the attached registration card is

returned to us within ten days of purchase.

This Guarantee is null and void if the R/C system has been im-

properly handled, damaged in a crash, or tampered with and

does not cover the replacement of plastic housings or electronic

components damaged due to the use of improper voltages.

When service is required, please take your equipment to your

local authorized service station or ship it directly to us. All

postage, shipping, and insurance charges must be paid by the

user.

(3) When motor car uses an ordi-

nary common power supply

chassis

Red common 2P

connector

(Female pins)

Buy the red common 2P

connector from the kit

manufacturer and connect to

the controller.

Pin 1: Minus

Pin 2: Plus

The Futaba BEC (Battery Eliminator Circuitry) system and BEC

& ASP (Adjustable Safety Position) system can also use a com-

mon power supply with the conventional four penlight batteries

system (separate power supply).

Connect the servo and switch as

shown in the figure and extend

the transmitter and receiver ante-

nna fully.

Red common 2P

connector (male pins)

Antenna mire

Receiver FP-R102GF

Switch

OFF

Steering servo

Throttle servo

Connection to this connector

(1)When chassis power supply of

engine or motor car is separate

Wrapped with

rubber band.

Red common 2P

connector

(Female pins)

Receiver crystal

Fig.

Connect to the red common

2P connector of the control-

ler.

Controller

Red common 2P

connector

(Female pins)

(2) When motor car uses a speci-

al 8EC system chassis (com-

mon power supply specifi-

cations)

(75MHz-OPTIONAL)

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Radio kontrol
Model:	FP2GS

Har du brug for hjælp?

Hvis du har brug for hjælp til Futaba FP2GS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radio kontrol Futaba Manualer

Futaba 9VAP Manual

25 August 2024

Futaba FP6FN Manual

25 August 2024

Futaba ATTACK_III Manual

25 August 2024

Futaba 3PV Manual

25 August 2024

Futaba GY440 Manual

25 August 2024

Futaba ATTACK_II Manual

25 August 2024

Futaba FP7FG Manual

25 August 2024

Futaba MAGNUM Manual

25 August 2024

Futaba 9CHPsuper Manual

25 August 2024

Futaba CGY750 V 2.0 Manual

25 August 2024

Radio kontrol Manualer

Nyeste Radio kontrol Manualer

Graupner GR-16L HoTT - S1021 Manual

13 Januar 2025

Rush SM 650 Manual

14 Oktober 2024

Sanwa RD6000 Manual

26 August 2024

Robbe Futaba FX-20 Manual

24 August 2024

Hitec PRISM_7X Manual

24 August 2024

Robbe Futaba T6EX Manual

23 August 2024

Multiplex Royal SX16 Manual

22 August 2024

Robbe Futaba R 6308 SB Manual

21 August 2024

JRpropo XP8103 Manual

21 August 2024

Hitec FOCUS_3SS_AM Manual

21 August 2024