Garmin GPSMAP 1200 Manual

Garmin Ikke kategoriseret GPSMAP 1200

Læs gratis den danske manual til Garmin GPSMAP 1200 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Garmin GPSMAP 1200, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
GPSMAP® 1000/1200 SERIES
Installation Instructions
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin® Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Support
• Go to for help and information, such as support.garmin.com
product manuals, frequently asked questions, videos, and
customer support.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
This device supports up to a 32 GB memory card, formatted to
FAT32.
Loading the New Software on a Memory Card
1Insert a memory card into the card slot on the computer.
2Go to .www.garmin.com/support/software/marine.html
3Select next to .Download GPSMAP Series with SD Card
4Read and agree to the terms.
5Select .Download
6Select .Run
7Select the drive associated with the memory card, and select
Next Finish > .
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1Turn on the chartplotter.
2After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3Follow the on-screen instructions.
4Wait several minutes while the software update process
completes.
5When prompted, leave the memory card in place and restart
the chartplotter manually.
6Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Tools Needed
• Drill
◦ Bail mount: drill bits appropriate for the surface and
hardware
◦ Flush mount: 14 mm (9/16 in.), 6 mm (1/4 in.) and 3.6 mm
(9/64 in.) (with nut plate), or 3.2 mm (1/8 in.) drill bit (with no
nut plate)
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (recommended)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, you should observe these
considerations.
• The location should provide optimal viewing as you operate
your boat.
• The location should allow for easy access to all device
interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
• The location must be strong enough to support the weight of
the device and protect it from excessive vibration or shock.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of all cables.
• The location must not be a flat, horizontal surface. The
location should be in a vertical angle.
January 2017 Printed in Taiwan 190-02145-02_0B
The location and viewing angle should be tested before you
install the device. High viewing angles from above and below
the display may result in a poor image.
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. It is recommended to apply an anti-seize
lubricant on the screws before installing them.
You can use a bail mount bracket (not included) to bail mount
the device on a flat surface.
1Using the bail-mount bracket À as a template, mark the pilot
holes.
2Drill the pilot holes.
3Using appropriate mounting screws (not included), secure the
bail-mount bracket to the mounting surface.
4Install the bail-mount knobs Á on the sides of the device.
5Place the device in the bail-mount bracket and tighten the
bail-mount knobs.
Flush Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
The included template and hardware can be used to flush mount
the device in your dashboard.
1Trim the template, and make sure it fits in the location where
you want to mount the device.
2Secure the template to the mounting location.
3Using a 14 mm (9/16 in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4Using a jigsaw or a rotary tool, cut the mounting surface
along the inside line on the template.
5Place the device in the cutout to test the fit.
6If necessary, use a file and sandpaper to refine the size of
the cutout.
7Use a pry tool, such as a flat piece of plastic or a screwdriver,
to carefully pry up the corners of the trim caps, slide the pry
tool to the center, and remove the trim caps.
NOTICE
Use a plastic pry tool when possible. Using a metal pry tool
such as a screwdriver can damage the trim caps and the
device.
8After the device fits correctly in the cutout, ensure the
mounting holes on the device line up with the larger 6 mm
(1/4 in.) holes on the template.
9If the mounting holes on the device do not line up, mark the
new hole locations.
10Select an option:
• If you are using a nut plate, drill a 6 mm (
1/4 in.) hole in the
larger hole location.
• If you are not using a nut plate, drill 3.2 mm (
1/8 in.) holes
in the larger hole locations.
11Starting in one corner of the template, place a nut plate
À
over the larger hole Á drilled in the previous step.
If you are using a nut plate, the smaller hole
 on the nut
plate should line up with the smaller hole on the template.
12If the smaller hole on the nut plate does not line up with the
smaller hole on the template, mark the new hole location.
13If you are using a nut plate, drill a 3.6 mm (
9/64 in.) hole in the
smaller hole location.
14Repeat to verify placement of the remaining nut plates and
holes on the template.
15Remove the template from the mounting surface.
16Starting in one corner of the mounting location, place a nut
plate à on the back of the mounting surface, lining up the
large and small holes.
The raised portion of the nut plate should fit into the larger
hole.
17Secure the nut plates to the mounting surface by fastening
the included M3 screws Ä through the smaller 3.6 mm
(9/64 in.) holes.
18Install the foam gasket Å on the back of the device.
The pieces of the foam gasket have adhesive on the back.
Make sure you remove the protective liner before installing
them on the device.
19If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
2

Produkt Specifikationer

Mærke: Garmin
Kategori: Ikke kategoriseret
Model: GPSMAP 1200

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin GPSMAP 1200 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Garmin Manualer

Garmin

Garmin Approach CT1 Manual

26 Februar 2025
Garmin

Garmin Spectra LC302 Manual

9 Januar 2025
Garmin

Garmin Spectra LC102 Manual

9 Januar 2025
Garmin

Garmin dēzl Headset 210 Manual

14 November 2024
Garmin

Garmin Inreach Messenger Plus Manual

11 November 2024
Garmin

Garmin GMM 170 Manual

4 Oktober 2024
Garmin

Garmin GMR 18 xHD Manual

4 Oktober 2024
Garmin

Garmin Edge Power Mount Manual

3 Oktober 2024
Garmin

Garmin GT30-TH Manual

3 Oktober 2024
Garmin

Garmin GMR 18 HD+ Manual

30 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Yamazen

Yamazen SAB-65 Manual

15 Juli 2025
GPX

GPX PJ504 Manual

15 Juli 2025
Transparent

Transparent TT-B Manual

15 Juli 2025
Yamazen

Yamazen ECSR-4538 Manual

15 Juli 2025
Yamazen

Yamazen SUS-205 Manual

15 Juli 2025
Yamazen

Yamazen YDG-160 Manual

15 Juli 2025
Yamazen

Yamazen OPR-5744 Manual

15 Juli 2025
Metabo

Metabo RW 18 LTX BL 120 Manual

15 Juli 2025
Victrola

Victrola Eastwood II VTA-74 Manual

15 Juli 2025
Axis

Axis T8415 Manual

15 Juli 2025