Garmin Livescope XR LVS62 Manual

Garmin Ekkolod Livescope XR LVS62

Læs gratis den danske manual til Garmin Livescope XR LVS62 (22 sider) i kategorien Ekkolod. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Garmin Livescope XR LVS62, eller vil du spørge andre brugere om produktet?

Side 1/22
LIVESCOPE LVS62 XR TRANSDUCER
INSTALLATION INSTRUCTIONS
Important Safety Information
Important Safety Information
Important Safety Information
Important Safety InformationImportant Safety Information
WARNING
See the guide in the chartplotter product box for product warnings and Important Safety and Product Information
other important information.
You are responsible for the safe and prudent operation of your vessel. Sonar is a tool that enhances your
awareness of the water beneath your boat. It does not relieve you of the responsibility of observing the water
around your boat as you navigate.
CAUTION
Failure to install and maintain this equipment in accordance with these instructions could result in damage or
injury.
To obtain the best performance and to avoid damage to your boat, you must install the Garmin® device
according to these instructions.
Read all installation instructions before proceeding with the installation. If you experience difficulty during the
installation, go to for more information.support.garmin.com
Software
Software
Software
SoftwareSoftware Update
Update
Update
Update Update
You must update the Garmin chartplotter software when you install this device. For instructions on updating the
software, see your chartplotter owner's manual at .support.garmin.com
Installation Support Videos
Installation Support Videos
Installation Support Videos
Installation Support VideosInstallation Support Videos
You can view videos online for assistance when installing this device.
You can access the videos by going to in your web browser or by garmin.com/videos/lvs62
scanning this QR code with your smartphone.
Tools Needed
Tools Needed
Tools Needed
Tools NeededTools Needed
• Drill
Drill bit suitable for the GLS 10 sonar module selected mounting hardware and surface
Flat screwdriver or 8mm wrench or socket to install the barrel mount clamp
Electrical tape (preferred) or cable ties
GUID-AF0D33F1-36EA-45B2-A50C-31466F679CB9 v2August 2022
Parts Bags
Parts Bags
Parts Bags
Parts BagsParts Bags
The installation hardware for the transducer is included in labeled bags. As you complete the installation
process, each procedure begins with a reference to the label on the parts bag needed to complete the
procedure. You can use this table to review or verify the parts bags needed for the installation procedures.
NOTE: You should leave all parts in the labeled bags until you are instructed to open a bag in the instructions.
Not all hardware is used for all installation types.
Contains parts needed when installing the perspective mount
Contains parts needed when installing the perspective or shaft mount
Contains parts needed when installing the perspective, shaft, or barrel mount
Contains parts needed when installing the barrel mount
Contains parts needed when installing the shaft mount
Contains the optional low-profile mounting screws
Mounting Considerations
Mounting Considerations
Mounting Considerations
Mounting ConsiderationsMounting Considerations
NOTICE
The use of third-party or self-fabricated mounts could lead to transducer damage or loss. Damage or loss
sustained when using a third-party or self-fabricated mount is not covered under warranty.
Using the hardware supplied, you can mount the transducer on your trolling motor in one of three ways.
Perspective Mount ( )Installing the Transducer on the Perspective Mode Mount, page5
You can mount the transducer on the trolling motor shaft using the perspective view mount and bracket.
When using the perspective view bracket, the transducer can be used for perspective, downward, and
forward views.
Barrel Mount ( )Installing the Transducer on a Trolling Motor Barrel, page9
You can mount the transducer on either side of the trolling motor barrel.
When mounted on the barrel, the transducer can be used for downward and forward views.
When mounted on the barrel, the transducer cannot be used for perspective view.
Shaft Mount ( )Installing the Transducer on the Trolling Motor Shaft, page11
You can mount the transducer on either side of the trolling motor shaft.
When mounted directly on the shaft, the transducer can be used for downward and forward views.
When mounted directly on the shaft, the transducer cannot be used for perspective view.
Mounting the transducer directly on the shaft allows a lower-profile installation than using the perspective-
mount bracket.
When planning the installation, you should observe these considerations.
You must angle the transducer correctly for the selected view to work properly.
Installing the transducer with the included knobs allows for tool-free transitions between sonar views.
You can use the included low-profile hardware instead of the knobs for a more permanent transducer view
position.
You should mount the transducer in a location where it will not be jarred when launching, hauling, or storing.
You must install the sonar module in a location with adequate ventilation where it will not be exposed to
extreme temperatures.
2


Produkt Specifikationer

Mærke: Garmin
Kategori: Ekkolod
Model: Livescope XR LVS62

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin Livescope XR LVS62 stil et spørgsmål nedenfor, og andre brugere vil svare dig