Garmin Reactor 40 Hydraulic Manual

Garmin Ikke kategoriseret Reactor 40 Hydraulic

Læs gratis den danske manual til Garmin Reactor 40 Hydraulic (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Garmin Reactor 40 Hydraulic, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

REACTOR™ 40 HYDRAULIC

Configuration Guide

Important Safety Information

WARNING

See the guide in the Important Safety and Product Information

product box for product warnings and other important

information.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Always be prepared to promptly regain manual control of your

boat.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

CAUTION

When in use, beware of hot motor and solenoid components

and the risk of entrapment from moving parts.

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

NOTICE

To avoid damage to your boat, the autopilot system should be

installed by a qualified marine installer. Specific knowledge of

hydraulic steering componentry and marine electrical systems is

required for proper installation.

Configuring the Autopilot

The autopilot system must be configured and tuned to your boat

dynamics. The Dockside Wizard and the Sea Trial Wizard are

used to configure the autopilot. These wizards walk you through

the necessary configuration steps.

If your autopilot package did not contain a helm control, you

must configure the autopilot system using a compatible

chartplotter on the same NMEA 2000® network as the autopilot

CCU. Instructions for configuration using either the helm control

or a chartplotter are provided.

Dockside Wizard

NOTICE

If you perform the Dockside Wizard while your boat is out of the

water, provide rudder-movement clearance to avoid damage to

the rudder or other objects.

You can complete the Dockside Wizard while the boat is in or

out of the water.

If the boat is in the water, it must be stationary while you

complete the wizard.

Performing the Dockside Wizard

NOTICE

If you have a boat with a power assist steering system, turn on

the power assist steering system before performing the

Dockside Wizard to avoid damaging the steering system.

1Turn on the autopilot.

The first time you turn on the autopilot, you are prompted to

complete a short setup sequence.

2If the does not start automatically after the Dockside Wizard

setup sequence, select an option:

• On a helm control, select > > Menu Setup Dealer

Autopilot Setup Wizards Dockside Wizard > > .

• On a chartplotter, select > >Settings My Vessel

Autopilot Installation Setup Wizards Dockside > >

Wizard.

3Select the vessel type.

4If prompted, follow the on-screen instructions to set the helm

lock-to-lock,

5If prompted, follow the on-screen instructions to provide the

helm displacement value.

6If necessary, calibrate the rudder sensor (Calibrating the

Rudder Sensor, page 1).

7Test the steering direction (Testing the Steering Direction,

page 1).

8If necessary, select the speed source (Selecting a Speed

Source, page 2).

9If necessary, verify the tachometer (Verifying the

Tachometer, page 2).

10If prompted, test the helm lock-to-lock.

11Review the results of the (Dockside Wizard Reviewing the

Results of the Dockside Wizard, page 2).

Calibrating the Rudder Sensor

NOTE: If an error appears during these steps, the rudder

feedback sensor may have reached its limit. If this happens, the

rudder feedback sensor may not have been installed correctly. If

the problem persists, you can continue with calibration by

moving the rudder to the farthest position that does not report an

error.

1Position the rudder so that the boat would steer fully

starboard, and select .OK

2After the starboard calibration is complete, position the

rudder so that the boat would steer fully port, and select .OK

3After the port calibration is complete, center the rudder

position, let go, and select .Begin

The autopilot takes control of the rudder.

4Without touching the rudder, helm control, or chartplotter,

allow the autopilot to calibrate the rudder.

5Select an option:

• If the calibration did not complete successfully, repeat

steps 1 through 4.

• If the calibration completed successfully, select .OK

Testing the Steering Direction

1While sitting still or moving at a low rate of speed, select

and .

When you select , the rudder must turn the boat to the left.

When you select , the rudder must turn the boat to the right.

2Select .Continue

3Select an option:

• If the steering test turns the boat in the correct direction,

on a helm control, select .Yes

• If the steering test turns the boat in the correct direction,

on a chartplotter, select .Next

• If the steering test turns the boat in the opposite direction,

on a helm control, select , and repeat steps 1 though 3.No

• If the steering test turns the boat in the opposite direction,

on a chartplotter, select , and repeatSwitch Direction

steps 1 though 3.

November 2017

190-02314-00_0A

Selecting a Speed Source

Select an option:

• If you connected one or more NMEA 2000 compatible

engines to the NMEA 2000 network, select Tachometer -

NMEA 2000.

• If a NMEA 2000 tachometer data source is not available

from one or more engines, or if it is unusable, select GPS

as a speed source.

NOTE: Garmin® recommends using an external GPS

antenna mounted with a clear view of the sky to provide

reliable and accurate GPS speed information.

• If you did not connect a NMEA 2000 engine or GPS

device as a speed source, select .None

NOTE: None If the autopilot does not perform well using

as the speed source, Garmin recommends connecting a

tachometer through the NMEA 2000 network or using an

external GPS antenna as the speed source.

Verifying the Tachometer

This procedure does not appear when GPS or None is selected

as the speed source.

With the engine (or engines) running, compare the RPM

readings on the helm control with the tachometer (or

tachometers) on the dashboard of your boat.

If the RPM numbers do not align, there may be a problem

with the NMEA 2000 speed source or connection.

Reviewing the Results of the Dockside Wizard

The values you chose when you ran the Dockside Wizard are

displayed.

1Examine the results of the .Dockside Wizard

2Select any incorrect value.

3Correct the value.

4Repeat steps 2 and 3 for all incorrect values.

5When you are finished reviewing the values, select .Done

Sea Trial Wizard

The Sea Trial Wizard configures the fundamental sensors on the

autopilot, and it is extremely important to complete the wizard in

conditions appropriate for your boat.

Important Sea Trial Wizard Considerations

The Sea Trial Wizard must be completed in calm water.

Because the nature of calm water is relative to the size and

shape of the boat, before you begin the Sea Trial Wizard, the

boat must be in an appropriate location.

• The boat must not rock while sitting still or moving very

slowly.

• The boat must not be significantly affected by the wind.

While completing the Sea Trial Wizard, observe these

considerations.

• Weight on the boat must remain balanced. While completing

any of the steps in the Sea Trial Wizard, do not move around

on the boat.

Performing the Sea Trial Wizard

1Drive your boat to an open area of calm water.

2Select an option:

• On a helm control, select > > Menu Setup Dealer

Autopilot Setup Wizards Sea Trial Wizard > > .

• On a chartplotter, select > > Settings My Vessel

Autopilot Installation Setup Wizards Sea Trial > >

Wizard Begin > .

3Select an option:

• On a planing-hull power boat with the speed source set to

Tachometer - NMEA 2000, configure the planing RPM.

• On a planing-hull power boat with the speed source set to

GPS, configure the planing speed.

• On a power boat with the speed source set to

Tachometer - NMEA 2000 GPS or , configure the high

RPM limit.

• On a power boat with the speed source set to , GPS

configure the maximum speed.

4Calibrate the compass ( ).Calibrating the Compass, page 2

5Perform the procedure (Autotune Performing the Autotune

Procedure, page 2).

6Set north ( ), or set the fine heading Setting North, page 3

adjustment ( ).Setting the Fine Heading Adjustment, page 3

Calibrating the Compass

1Select an option:

• If you are performing this procedure as part of the Sea

Trial Wizard Begin, select .

• If you are performing this procedure outside of the Sea

Trial Wizard on a helm control, from the heading screen,

select > > > Menu Setup Dealer Autopilot Setup

Compass Setup Calibrate Compass Begin > > .

• If you are performing this procedure outside of the Sea

Trial Wizard Settings My on a chartplotter, select >

Vessel Autopilot Installation Setup Compass > >

Setup Compass Cal. Begin > > .

2Follow the directions until calibration is complete, taking care

to keep the boat as steady and flat as possible.

The boat should not list during calibration. Make sure one

side of the vessel is not loaded more heavily than the other.

3Select an option:

• If the calibration completes successfully on a helm control,

select .Done

• If the calibration completes successfully, on a chartplotter

select .OK

• If the calibration is not successful, select and repeat Retry

steps 1 through 3.

When the calibration is complete, a magnetic environment

quality value is shown. A value of 100 indicates the CCU was

installed in a perfect magnetic environment and calibrated

correctly. If this value is low, you might need to relocate the

CCU and calibrate the compass again.

Performing the Autotune Procedure

Before you can begin this procedure, you must have a large

stretch of open water available.

1Adjust the throttle so the boat travels at a typical cruising

speed (below planing speed) that provides responsive

steering.

2Select an option:

• If you are performing this procedure as part of the Sea

Trial Wizard Begin, select .

• If you are performing this procedure outside of the Sea

Trial Wizard on a helm control, from the heading screen,

select > > > Menu Setup Dealer Autopilot Setup

Autopilot Tuning Autotune Begin > > .

• If you are performing this procedure outside of the Sea

Trial Wizard Settings My on a chartplotter, select >

Vessel Autopilot Installation Setup Autopilot > >

Tuning Autotune Begin > > .

The boat performs various zigzag motions while the Autotune

is in progress.

3After the procedure is finished, follow the on-screen

instructions.

Produkt Specifikationer

Mærke:	Garmin
Kategori:	Ikke kategoriseret
Model:	Reactor 40 Hydraulic

Har du brug for hjælp?

Hvis du har brug for hjælp til Garmin Reactor 40 Hydraulic stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Garmin Manualer

Garmin Foretrex 701 Ballistic Edition Manual

12 August 2025

Garmin Approach CT1 Manual

26 Februar 2025

Garmin dēzl Headset 110 Manual

8 Februar 2025

Garmin Spectra LC302 Manual

9 Januar 2025

Garmin Spectra LC102 Manual

9 Januar 2025

Garmin dēzl Headset 210 Manual

14 November 2024

Garmin Inreach Messenger Plus Manual

11 November 2024

Garmin GMM 170 Manual

4 Oktober 2024

Garmin GMR 18 xHD Manual

4 Oktober 2024

Garmin Edge Power Mount Manual

3 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Sungrow SH10RT-V113 Manual

18 Oktober 2025

AstralPool Niche Switch Manual

18 Oktober 2025

Sungrow SH8.0RT-V113 Manual

18 Oktober 2025

AstralPool Roma Manual

18 Oktober 2025

Evenflo SafeMax Manual

18 Oktober 2025

NEO Tools 94-002 Manual

18 Oktober 2025

LC-Power Platinum Pro LC1000P V3.1 Manual

17 Oktober 2025

Metz 130B21-E Manual

17 Oktober 2025

NEO Tools 99-038 Manual

17 Oktober 2025

FBT MPU 2120 Manual

17 Oktober 2025