GE GXITD Manual

GE Ikke kategoriseret GXITD

Læs gratis den danske manual til GE GXITD (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 9 anmeldelser. Har du et spørgsmål om GE GXITD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Service Service Max. Average Average

Model Flow rate Life Pressure Temp. Contaminant % Reduction Influent Effluent

GXITD

0.5 gpm 2000 gal. (7571 liters) 25–125 psi 100°F. Chlorine 93% 2.0 mg/L 0.1 mg/L:

(1.9 lpm) or 6 months (172–862 kPa) (38°C.)

GE SmartWater™

GE Model GXITD Filter

Do not use with water that is microbiologically

unsafe or with water

of unknown quality without adequate disinfection before or after

the system.

Small parts remaining after the installation could be a choke

hazard. Discard safely.

System Tested and Certified by NSF International against

ANSI/NSF Standard 42 for

the reduction of Taste and Odor,

and Chlorine, Class I.

WARNING

INSTALLATION PRECAUTIONS

•Protect from freezing. Drain filter when room temperature drops below 32°F. (0°C.).

•Use the in-line water filtering system on a potable, safe-to-drink, home COLD water supply only.

The filter will not make unsafe water safe to drink. Do NOT use on HOT water (100°F. max.).

•Do not install on line pressure above 125 psi (862 kPa), or below 25 psi (172 kPa).

•All of the refrigerator installation requirements must be met when installing the filter.

•Do not use wicking or pipe dope sealer for fitting connections into head of filter. Teflon® tape is recommended and included.

Teflon is a registered trademark of DuPont.

•Do not install in direct sunlight.

•Installation must comply with existing state or local plumbing codes.

•It is essential that operational, maintenance and filter replacement requirements be carried out for this product to perform as advertised.

Change filter at least every six months. Flush new cartridge for 5 minutes.

REQUIRED TOOLS FOR INSTALLATION

•a tube cutter

• 7/16 1/2 and 9/16 wrenches″, ″ ″

• a knife

• a bucket or pan

OPTIONAL TOOLS FOR INSTALLATION

•a file

•sandpaper

CAUTION: Using pliers or vise grips damage the fittings.WILL

Your new GE icemaker water filter comes complete with all the necessary hardware for installation. Each filter gives you up to six

months of great-tasting water. Filter should be changed after 6 months of use.

SPECIFICATIONS

Testing parameters: Influent Challenges = pH 7.5 ± 0.5; Temperature 68°F ± 5°F (20°C ± 3°C); Pressure 60 psig; Flow Rate = 1gpm

If slow water or hollow ice occurs, replace filter.

Part No. 251B6017P003 Pub. No. 49-50047(10-99 JR)

For service, parts, or maintenance call: GE Answer Center® 800.626.2000

GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225

LIMITED 60 DAY WARRANTY

•What does this warranty cover?

— Any defect in materials or workmanship in the manufactured product.

•What does this warranty not cover?

— Customer installation. The Installation Instructions cover installation and

replacement instructions.

— Defects that result from abuse, misuse, alterations, improper installation or

damage not caused by GE.

— Liability on the part of GE under this or any other warranty for any indirect or

consequential damage.

— Products that are used for commercial or industrial applications.

•For how long after the original purchase?

— Sixty (60) days.

•How do I make a warranty claim?

— Return to the retailer from which it was purchased along with a copy of the “Proof

of Purchase.”

•How does state law relate to this warranty?

— This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Attach Fittings to Filter

2. a. Remove yellow endcaps from filter.

b. Find the ends of brass fittings that mate with

filter body.

c. Apply 1 to 2 wraps of the included Teflon

tape to threads, as shown.

d.Thread brass fittings into both ends of the

filter body and tighten snug with a wrench.

Cut Tubing

3. Shut off water supply.

The filter is to be inserted (spliced) into the

1/4

″

OD supply tube that feeds water to the

refrigerator. (Do not cut any water lines

internal to the refrigerator.) Locate the filter

as close as possible to the supply water shut-off

valve. If the filter needs to be located behind

the refrigerator, there needs to be at least 6

inches of clearance between the wall and the

refrigerator. If the appliance must be moved,

make sure there is proper protection on

the floor.

5. Cut the tubing, making sure the ends are

square and no burrs protrude. Deburr ends

with file or sandpaper if necessary.

Attach Fittings to Tubing

6. Slip brass nuts then ferrules over both tubing

ends, leaving 1/4 of tubing exposed from″

end.

(See figure for ferrule orientation).

For copper tubing, use the brass ferrules.

For plastic tubing, use plastic ferrules and

brass inserts.

7. Connect the supply water line to the filter

inlet:

a. Insert end of tubing into brass fitting; hand-

tighten nut onto threads of brass fitting.

b. Using two wrenches, tighten nut at least one

full turn.

CAUTION: Be careful not to cross thread the nut

and the fitting.

See step 8 below to complete the installation.

Teflon

tape

Brass nut Brass nut

Brass insert

(for plastic tubing)

Brass insert

(for plastic tubing)

Water line

tubing Water line

tubing

Ferrule FerruleBrass

fitting

Brass

fitting

SUPPLY SIDE INLET OUTLET APPLIANCE SIDE

Follow Directions for Proper Assembly

Flush Filter

8. Place filter outlet over bucket or pan. Turn on the incoming water

supply to

flush

the filter into

the bucket or pan thereby removing fine

particles of carbon which may be present. Flush 2 to 3 gallons of water

(approx. 5 minutes). Turn off the water supply.

Final Connection and Leak Check

9. Connect the

outlet

port of the filter to the water line to your appliance

in the same manner as the inlet.

10. Turn on water supply line. If leak occurs, tighten nuts or fittings until

leak stops.

11. Write the date on the filter and also mark your calendar to replace

with another filter after six months.

12. Discard any unused parts.

OPTION 1:

Brass Fittings

Attach Fittings to Filter

2. a. Remove yellow endcaps from filter.

b. Apply 1 to 2 wraps of the included Teflon

tape to threads of o-ring fittings, as shown.

c. Thread o-ring fittings into both ends of the

filter body and tighten snug with a wrench.

Leave at least one turn of thread showing.

Cut Tubing

3. Shut off water supply.

4. The filter is to be inserted (spliced) into the

1/4 OD supply tube that feeds water to the″

refrigerator. (Do not cut any water lines

internal to the refrigerator.) Locate the filter

as close as possible to the supply water shut-

off valve. If the filter needs to be located

behind the refrigerator, there needs to be at

least 6 inches of clearance. If the appliance

must be moved, make sure there is proper

protection on the floor.

5. Cut the tubing, making sure the ends are

square and no burrs protrude. Deburr ends

with file or sandpaper if necessary.

Attach Fittings to Tubing

6. Slip brass

nuts then ferrules over both tubing

ends, leaving 1/4 of tubing exposed from″

end. (See figure for ferrule orientation). For

both copper and plastic tubing, use plastic

ferrules. If your tubing is plastic, place brass

inserts into ends of tubing.

7. a. Insert end of supply side tubing into the

valved fitting (the

longer

fitting);

hand-

tighten nut onto threads of fitting.

CAUTION: Be careful not to cross thread

the nut and the fitting.

b. Using two wrenches, tighten nut at least

one full turn.

c. Valved fitting is now installed. Turn water

supply on and inspect for leaks.

d. Repeat a band for non-valved fitting on

the appliance side.

See step 8 below to complete the installation.

Teflon

tape

Brass nut Brass nut

Brass insert (for

plastic tubing) Brass insert (for

plastic tubing)

Water line

tubing

Water line

tubing

Ferrule FerruleValved fitting Non-valved

fitting

O-ring

fitting

O-ring

fitting

SUPPLY SIDE INLET OUTLET APPLIANCE SIDE

Follow Directions for Proper Assembly

OPTION 2:

Quick Connect

Installation Kit

QCKIT

(sold separately)

1. All of the

refrigerator

installation

requirements

must be met

when installing

the filter.

1. All of the refrigerator

installation

requirements must

be met when

installing the filter.

INSTALLING THE FILTER

Two installation methods are available: • Option 1 (brass fittings) • Option 2 (quick-connect fittings)

Produkt Specifikationer

Mærke:	GE
Kategori:	Ikke kategoriseret
Model:	GXITD

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GXITD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret GE Manualer

GE Create Jason Wu Manual

7 April 2025

GE GFC325N Manual

9 December 2024

GE ZXR7510C Manual

6 Oktober 2024

GE GXITD Manual

16 September 2024

GE Profile UCG1600LWW Manual

28 August 2024

GE Profile GCG1580LSS Manual

26 August 2024

19 August 2024

13 August 2024

9 August 2024

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kora DTR-3342 Manual

16 Juni 2025

Playtive IAN 346914 Manual

16 Juni 2025

Playtive IAN 303641 Manual

16 Juni 2025

Playtive HG05107 Manual

16 Juni 2025

Playtive IAN 346906 Manual

16 Juni 2025

Playtive IAN 285778 Manual

16 Juni 2025

Planet Audio PCBLK3.5 Manual

16 Juni 2025

Sabrent NT-UA25 Manual

16 Juni 2025

ElectriQ STRV-Z1-WH Manual

16 Juni 2025

Watts ETX-30 Manual

16 Juni 2025