GE Profile JXDFT214 Manual

GE Ikke kategoriseret Profile JXDFT214

Læs gratis den danske manual til GE Profile JXDFT214 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om GE Profile JXDFT214, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
49-2001155 Rev. 0 08-22 GEA
Drawer Front Accessory JXDF21T for RV Range
Owner's Manual and
Installation Instructions
Installation Instructions
Use Figure 1 to determine the preferred mounting position of the drawer front to the drawer face.
WARNING Position the drawer front in relation to the
drawer face so that the top of the drawer front is at least
1/2" below the bottom of the range door. This positioning is
important to ensure proper airflow for combustion and cooling
to your range. Proper positioning of the drawer front will also
ensure the range door will not interfere with the drawer front as
the range door and drawer open and close (see Figure 2).
Figure 2
Top of drawer front should
be at least 1/2" below
bottom of range door.
NO SCREW ZONE
NO SCREW ZONE
Overall Width = 21-1/2" (544 mm)
7-3/4" (195 mm) 7-3/4" (195 mm) 3"
(77 mm)
3"
(77 mm)
4"
(100 mm)
4"
(100 mm)
2-3/4"
(70 mm)
1"
(25 mm)
1"
(25 mm)
Overall
Height =
11-1/2"
(292 mm)
6-5/16"
(161 mm)
5-3/16"
(131 mm)
Figure 1
Pilot Holes
x6
What you will need for installation:
• Tape Measure
• Drill with drill bits
• 6 Screws
• Screwdriver
249-2001155 Rev. 0
Use one of the following 2 methods for proper installation:
Method 1: Use existing 6 holes
• The drawer front comes with 6 extruded pilot holes for attaching to the drawer face.
• Referencing the screw spacing from Figure 1, mark on the front face of the drawer where the 6 pilot holes will align.
• Use an appropriately sized drill bit to drill clearance holes through the drawer face.
• It is recommended to use 6 screws with a sheet metal thread that are at least #8 size and long enough to go through
the drawer face and secure into the drawer front. Ensure the screws are not too long and do not interfere with the front
panel of the drawer front.
• Screw the drawer front to the drawer face being careful not to over tighten and strip the screws.
Method 2: Create new pilot holes (use this method if you prefer to mount the drawer
front using holes other than the 6 existing holes)
• It is recommended to use 6 attachment screws positioned around the perimeter of the drawer face. The screws should
be positioned vertically and horizontally as far as possible on the drawer face to ensure maximum stiffness of the
drawer front. Be sure to avoid the "no screw zone" locations from Figure 1.
• It is recommended to use 6 self-tapping screws with a sheet metal thread that are at least #8 size and long enough to
go through the drawer face and secure into the drawer front. Ensure the screws are not too long and do not interfere
with the front panel of the drawer front.
• Use an appropriately sized drill bit to drill clearance holes through the front face of the drawer. This step is optional if
using self-tapping screws.
• Screw the drawer front to the drawer face being careful not to over tighten and strip the screws.
Installation
Care and Cleaning
Painted Drawer Panel
Clean the painted drawer panel with soap and water or a
vinegar and water solution. Do not use commercial oven
cleaners, cleaning powders, steel wool or harsh abrasives
on any painted surface.
Stainless Steel Handle
Do not use a steel wool pad; it will scratch the surface. To
clean the stainless steel surface, use warm sudsy water or
a stainless steel cleaner or polish. Always wipe the surface
in the direction of the grain. Follow the cleaner instructions
for cleaning the stainless steel surface. Cleaners with
oxalic acid such as Bar Keepers Friend Soft Cleansers will
remove surface rust, tarnish, and small blemishes. Use
only a liquid cleanser free of grit and rub in the direction of
the brush lines with a damp, soft sponge.

Produkt Specifikationer

Mærke: GE
Kategori: Ikke kategoriseret
Model: Profile JXDFT214

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile JXDFT214 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret GE Manualer

GE

GE GFC1065 Manual

12 August 2025
GE

GE WM1050 Manual

6 August 2025
GE

GE JXCHWW Manual

5 August 2025
GE

GE JXRB67 Manual

5 August 2025
GE

GE UXB903SNSS Manual

5 August 2025
GE

GE E1240 Manual

6 Juli 2025
GE

GE Profile PWL1126SS Manual

5 Juli 2025
GE

GE Create Jason Wu Manual

7 April 2025
GE

GE GFC325N Manual

9 December 2024
GE

GE ZXR7510C Manual

6 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo

Festo SOEG-S-M18W-S-L Manual

18 August 2025
Festo

Festo SIED-M30NB-ZO-S-L Manual

18 August 2025
Parkside

Parkside PFBSA 4 A1 Manual

18 August 2025
Martin

Martin VC-Dot 4 Manual

18 August 2025
Smart-AVI

Smart-AVI QKVM-DP Manual

18 August 2025
Festo

Festo SOEG-RTH-M18-NS-S-2L Manual

18 August 2025
Festo

Festo CPV10-VI-P4-M7-D Manual

18 August 2025
D-Link

D-Link DI-206 Manual

18 August 2025
Royal Catering

Royal Catering RCWF-10LE-H Manual

18 August 2025
Festo

Festo SIED-M30B-ZO-K-L Manual

18 August 2025