GE SmartWater Manual

GE Ikke kategoriseret SmartWater

Læs gratis den danske manual til GE SmartWater (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 80 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 40.5 anmeldelser. Har du et spørgsmål om GE SmartWater, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

TOOLS AND MATERIALS REQUIRED

•Utility knife

•Pliers and adjustable wrench

•Pipe cutter

•File or Emery cloth (or fine sandpaper)

CAUTION: To prevent voiding the GE warranty,

⁄

″

copper tubing must be used where water supply

connects to the icemaker water supply valve on

the back of the refrigerator.

KIT CONTENTS

•20′ Polyethylene tubing (3⁄8″dia.)

•Plastic bag containing:

•3⁄8″ Tee-fitting with nuts

•(4) Plastic inserts

•1 Reducer fitting with:

•(1) 3⁄8″ std nut w/integral ferrule

•(1) 1⁄4″ steel gripper

•(1) 1⁄4″ sleeve

•(1) 1⁄4″ nut

•(1) 3⁄8″ to 1⁄4″ reducer fitting

OUTILS ET MATÉRIEL NÉCESSAIRES

•Couteau utilitaire

•Pince et clé à molette

•Coupe tube

•Lime et toile émeri (papier abrasif)

MISE EN GARDE : Pour éviter d’invalider la

garantie GE, on doit utiliser du tube de cuivre de

⁄

pouce pour relier la canalisation d’eau au point

du robinet d’alimentation de la machine à

glaçons à l’arrière du réfrigérateur.

CONTENU DE L’ENSEMBLE

•Tube de polyéthylène (diam. 3⁄8po) – 20 pieds (6.5 m)

•Sachet de plastique contenant :

•Raccord T de 3⁄8po avec écrou

•4 Viroles de plastique à insérer

•1 Raccord de réduction avec :

•(1) écrou standard 3⁄8po et virole intégrée

•(1) rondelle d’acier agrippante, 1⁄4po

•(1) virole 1⁄4po

•(1) écrou 1⁄4po

•(1) raccord de réduction 3⁄8po – 1⁄4po

HERRAMIENTAS Y MATERIALES NECESARIOS

•Cuchillo de uso general

•Pinzas y llave de tuercas

•Corta tubos

•Lima o tela esmeril (papel de lija fino)

PRECAUCION: Para evitar la anulación de la

garantía de GE, es necesario usar tubería de

cobre de

⁄

″

en donde el suministro de agua se

conecte la valvula al suministro de agua de la

máquina de hielo en la parte trasera del

refrigerador.

CONTENIDO DEL JUEGO DE INSTALACIÓN

•20 pies (6.5 m) de tubería de polietileno

(de 3⁄8″de diámetro)

•Una bolsa de plástico conteniendo:

•Conexión en T de 3⁄8″ con tuercas

•(4) Insertos de plástico

•1 Accesorio reductor con:

•(1) tuerca estándar con férula integral de 3⁄8″

•(1) agarrador metálico de 1⁄4″

•(1) manguito de 1⁄4″

•(1) tuerca de 1⁄4″

•(1) accesorio reductor de 3

⁄8″ a 1⁄4″

Instructions d’installation en français : page 3.

Pour utilisation avec tout système de filtration à carbon de GE SmartWater à un ou deux modules .

(Ne pas utiliser avec un système à osmose inverse.)

Instrucciones de instalación en Español: página 4.

Debe ser usado con todos los sistemas de filtración de carbón de agua de sumidero sencillo o doble

GE SmartWater. (No es para utilizarse en sistemas de osmosis inversa.)

GE SmartWater

Water Filtration System Icemaker Connection Kit (UCKIT)

INSTALLATION INSTRUCTIONS

For use with all GE SmartWater™Single or Dual stage carbon filtration systems.

(Not for use with reverse osmosis systems.)

7190319 Part No. 215C1001P012-1 Pub. No. 49-5837-1(12-99 JR)

This kit is designed to be used with either a new water filtration

installation requiring an icemaker connection or an existing filtration

system to add an icemaker connection.

1. Install the filtration system as detailed in the unit’s installation

instructions, if it has not been done already.

2. Turn off the water supply/saddle valve to the filter. Relieve

water pressure by pressing button on sump (tank) or opening

the faucet.

3. Locate the faucet supply tube connecting the filtration unit

to the faucet. Cut the tube at a convenient location.

4. Connect the tee fitting to the two cut ends of the supply

tubing

(see Fig. 1). Position plastic tube inserts, thread nuts onto fitting,

and hand tighten. If necessary, complete tightening with a wrench*.

5. Connect one end of the 20 of supplied ′ 3⁄8″ tube to the third end

of the tee fitting.

Position plastic tube inserts, thread nuts onto

fitting, and hand tighten. If necessary, complete tightening with

a wrench*.

6. TURN OFF THE ICEMAKER. TURN OFF ICEMAKER WATER

SOURCE (IF APPLICABLE). Disconnect the current icemaker

water source, if applicable. DO NOT disconnect the tubing from

the valve attached to the back of the refrigerator (see Fig. 3).

7. Cut plastic tubing to desired length. Slide 3⁄8″ compression nut

over the plastic tubing free end, fit insert into tubing and hand

start nut to reducer fitting. Tighten with a wrench the final 11⁄2

to 2 turns*.

8. Cut copper tubing connected to the icemaker valve to the

desired length and remove any burrs. Leave sufficient copper

tubing to allow movement of the refrigerator for service.

9. Slide 1⁄4″nut over copper tubing, then steel gripper, then plastic

sleeve. Slide components to reducer fitting. Hand start nut to

reducer fitting (see Fig. 2). Tighten with a wrench the final 11⁄2

to 2 turns*.

10. Turn on the water supply valve to the filter. Check all fittings

for leaks. Turn on icemaker.

* Make sure tubing is fully inserted and bottoms out.

For Use and Care questions call:

GE Answer Center® 800.626.2000

GENERAL ELECTRIC COMPANY

Appliance Park, Louisville, KY 40225

Fig. 1

Fig. 2

Sink

Hot

Cut

Cold

Water supply/

saddle valve

Plastic

Tee fitting

Water

inlet

Water

outlet

3/8 plastic tubing″

Icemaker water valve

Filter I

Filter II

INSTALLATION INSTRUCTIONS

TYPICAL KIT INSTALLATION

Fig. 3

3/8″plastic nut

3/8 plastic insert″

3/8 plastic nut″

1/4 copper tubing″

1/4″nut

1/4″steel gripper

1/4 plastic sleeve″

1/4 coupling end″

3/8 coupling end″

3/8 plastic insert″

Back of

refrigerator

FLOW

Reducer

Pressure release

button

Produkt Specifikationer

Mærke:	GE
Kategori:	Ikke kategoriseret
Model:	SmartWater

Har du brug for hjælp?

Hvis du har brug for hjælp til GE SmartWater stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret GE Manualer

12 August 2025

6 August 2025

5 August 2025

5 August 2025

5 August 2025

6 Juli 2025

GE Profile PWL1126SS Manual

5 Juli 2025

GE Create Jason Wu Manual

7 April 2025

GE GFC325N Manual

9 December 2024

GE ZXR7510C Manual

6 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo SOEG-S-M18W-S-L Manual

18 August 2025

Festo SIED-M30NB-ZO-S-L Manual

18 August 2025

Parkside PFBSA 4 A1 Manual

18 August 2025

Martin VC-Dot 4 Manual

18 August 2025

Smart-AVI QKVM-DP Manual

18 August 2025

Festo SOEG-RTH-M18-NS-S-2L Manual

18 August 2025

Festo CPV10-VI-P4-M7-D Manual

18 August 2025

D-Link DI-206 Manual

18 August 2025

Royal Catering RCWF-10LE-H Manual

18 August 2025

Festo SIED-M30B-ZO-K-L Manual

18 August 2025