Genelec 4010A Manual

Genelec Skærm 4010A

Læs gratis den danske manual til Genelec 4010A (8 sider) i kategorien Skærm. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Genelec 4010A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

4010A

Operating Manual

2 English

4010A

Active Loudspeaker

General

The bi-amplified Genelec 4010A is an extremely

compact two way active loudspeaker designed for

xed installations. It contains drivers, power ampli-

ers, active crossover lters and protection circuitry.

The 4010A is designed for indoor use only, in tem-

peratures between 15 to 35 degrees Celsius and

relative humidity between 20 % and 90 %.

The MDE™ (Minimum Diraction Enclosure™)

loudspeaker enclosure is made of die-cast alumin-

ium and shaped to reduce edge diraction. Com-

bined with the advanced Directivity Control Wave-

guideTM (DCWTM), this design provides excellent

frequency balance in dicult acoustic environments.

Delivery contents

Each 4010A is supplied with a mains cable, a 3-pin

connector for audio signal, a keyhole type wallmount

and an operating manual.

Connections

Connect the mains cables only after you have com-

pleted connecting audio signal cabling.

Audio input is via a 10 kOhm balanced connec-

tor. The pin sequence of the connector is shown

in Figure 2.

Connect the signal cable to the 3-pole plug pro-

vided with the loudspeaker and secure the connec-

tions by tightening the screws on each pole. Push

the plug into the connector on the loudspeaker.

Never connect the 4010A to the loudspeaker

outputs of a power amplier, integrated amplier

or receiver.

When all audio connections are completed,

connect the loudspeakers to mains with the sup-

plied mains cables. They will switch on automati-

cally.

ISSTM Autostart

The 4010A is equipped with Intelligent Signal Sens-

ingTM (ISSTM) Autostart function, which automati-

cally turns the amplier to Standby mode if an input

signal has not been detected for approximately 1

hour. The power consumption in standby mode is

typically less than 0.5 watts. The playback will au-

tomatically resume once an input signal is detected

from the source.

There is a slight delay in the automatic power-

ing up. If this is undesirable, the ISSTM function can

be disabled by setting the “ISS DISABLE” switch

on the back panel to “ON” position. In this mode,

the loudspeaker is powered on and o using the

power switch on the back panel.

Sensitivity control

The input sensitivity (playback level) of the 4010A

has two alternative settings, normal and -10 dB.

The normal setting is factory default and the low-

er, -10 dB setting can be selected by turning the

“SENSITIVITY -10 dB” switch on the back panel to

“ON”.

The output levels are 100 dB @ -6dBu and 90

dB @ -6 dBu respectively. Choose the setting that

Operating Manual

Produkt Specifikationer

Mærke:	Genelec
Kategori:	Skærm
Model:	4010A
Vekselstrømsindgangsspænding:	100-240 V
Vekselstrømsindgangsfrekvens:	50-60 Hz
Bredde:	121 mm
Dybde:	115 mm
Højde:	181 mm
Vægt:	1500 g
Produktfarve:	Sort
Udgangseffekt (RMS):	30 W
Anbefalet brug:	Studio
Frekvensområde:	67 - 25000 Hz
Lydtryksniveau (maks.):	96 dB
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	- kanaler
Højttaler, placering:	Floor, Tabletop/bookshelf
Diskanthøjttaler:	Ja
Diskant diameter:	19 mm
Forstærker:	Indbygget
Forstærker klasse:	D
Højttaler kabinet:	Refleks