Genelec 4020C Manual


Læs gratis den danske manual til Genelec 4020C (8 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Genelec 4020C, eller vil du spørge andre brugere om produktet?

Side 1/8
4020C
Operating Manual
2
General
The bi-amplied Genelec 4020C is an extremely
compact two way active loudspeaker designed for
xed installations. As an active loudspeaker, it con-
tains drivers, power ampliers, active crossover l-
ters and protection circuitry. The 4020C is designed
for indoor use only, in temperatures between 15 to
35 degrees Celsius and relative humidity between
20 % and 90 %.
The MDE™ (Minimum Diraction Enclosure™)
loudspeaker enclosure is made of die-cast alumin-
ium and shaped to reduce edge diraction. Com-
bined with the advanced Directivity Control Wave-
guideTM (DCWTM), this design provides excellent fre-
quency balance in dicult acoustic environments.
Positioning the loudspeaker
Each 4020C is supplied with an integrated ampli-
er unit, mains cable, a 3-pin balanced Euroblock
connector for audio signal, a keyhole type wall-
mount and an operating manual. After unpacking,
place the loudspeaker in its required listening posi-
tion, taking note of the line of the acoustic axis. The
axis should be pointed towards the center of the
listening area.
Connections
Before connecting up, ensure that the loudspeakers
and the signal source have been switched o. The
power switch of the 4020C is located on the back
panel (see Figure 3). Connect the loudspeaker to an
earthed mains connection with the supplied mains
cable. Never connect the loudspeaker to an un-
earthed mains supply or using an unearthed mains
cable. Audio input is via a 10 kOhm balanced
connector. The pin sequence of the connector is
shown in Figure 2.
Connect the signal cable to the 3-pole plug pro-
vided with the loudspeaker and secure the con-
nections by tightening the screws on each pole.
Push the plug into the connector on the loud-
speaker.
If you want to daisy-chain multiple loudspeak-
ers, simply connect a second signal cable to the
plug and use it to route the signal to the next loud-
speaker (see Figure 4).
Never connect the 4020C to the loudspeaker
outputs of a power amplier or an integrated am-
plier or receiver.
Once the connections have been made, the
loudspeakers are ready to be switched on.
ISSTM Autostart
The automatic power saving function ISS (Intelli-
gent Signal Sensing) can be activated by setting
the “ISS” switch on the back panel to “ON.” Auto-
matic powering down to standby mode happens
after a certain time when playback has ended. The
power consumption in standby mode is typically
less than 0.5 watts. Playback will automatically
resume once an input signal is detected from the
source.
There is a slight delay in the automatic pow-
ering up. If this is undesirable, the ISS TM function
can be disabled by setting the ISS” switch on the
back panel to “OFF.” In this mode, the loudspeak-
er is powered on and o using the power switch
on the back panel.
4020C
Active Loudspeaker


Produkt Specifikationer

Mærke: Genelec
Kategori: overvåge
Model: 4020C

Har du brug for hjælp?

Hvis du har brug for hjælp til Genelec 4020C stil et spørgsmål nedenfor, og andre brugere vil svare dig




overvåge Genelec Manualer

Genelec

Genelec 8341A Manual

27 September 2024
Genelec

Genelec 4420A Manual

27 September 2024
Genelec

Genelec 7380A Manual

19 September 2024
Genelec

Genelec 8320A Manual

4 August 2024
Genelec

Genelec 8331A Manual

3 August 2024
Genelec

Genelec 7360A Manual

1 August 2024
Genelec

Genelec 7050C Manual

31 Juli 2024
Genelec

Genelec S360A Manual

28 Juli 2024
Genelec

Genelec 1237A Manual

22 Juli 2024

overvåge Manualer

Nyeste overvåge Manualer