Satco S16434 Manual

Satco overvåge S16434

Læs gratis den danske manual til Satco S16434 (4 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Satco S16434, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

of the lamp is powered, and securely connected to the

powered R17d lamp holders (120V-277V).

STEP 9: Make sure all sockets are wired according to the

appropriate wiring diagram (Figures 1/1a – 4/4a).

STEP 10: Reinstall the ballast cover to hide all wires.

STEP 11: Install your new single and double ended LED T8

replacement lamps.

STEP 12: Apply

relamping label on a

visible location inside

the xture.

STEP 13: Reinstall lens

or diffusion cover on the

light xture.

STEP 14: Turn power

ON at the breaker box.

STEP 15: Turn on the lights.

OMNI

DIRECTIONAL LED T8 TUBES

Models: S16430, S16431, S16432, S16433, S16434, S16435, S16436,

S16437, S16438, S16439, S16440, S16441, S16442, S16443

Satco Products, Inc.

WARNING:

• DANGER: Risk of shock-disconnect power before

installation.

• WARNING: Risk of re or electric shock. LED Retrot

Kit installation requires knowledge of luminaire electrical

systems. If not qualied, do not attempt installation.

Contact a qualied electrician.

• WARNING: Product must be installed in accordance with

the national electrical code or your local electrical code.

If you are not familiar with these codes and requirements,

contact a qualied electrician.

• WARNING: Install this kit only in luminaries that have

the construction features and dimensions shown in the

photographs and/or drawing and where the input rating

of the retrot kit does not exceed the input rating of the

luminaire.

• WARNING: To prevent wiring damage or abrasion, do

not expose wiring to edges of sheet metal or other sharp

objects. Do not make or alter any open holes in any

enclosure of wiring or electrical components during kit

installation.

• WARNING: To avoid potential re or shock hazard, please

conﬁrm the type of lamp holder before installation. If it is a

shunted lamp holder, refer to double-ended wiring.

NOTE: Shunted lamp holders are found only in

uorescent luminaries with instant-start ballasts. Instant-

start ballasts can be identied by the words “Instant

Start” or “I.S.” marked on the ballast. This designation

may be in the form of a statement pertaining to the

ballast itself, or may be combined with the marking for

the lamps with which the ballast is intended to be used,

for example F40T 12/IS, for more information contact the

LED luminaire retrot kit manufacturer.

If it is non-shunted lamp holder, refer to single or

double-ended wiring.

Installers should not disconnect the existing wire from

lampholder terminals to make new connections at

lampholder terminals. Instead installers should cut

existing lampholder leads away from the lampholder and

make new electrical connections to lampholder lead wires

by employing applicable connectors.

• WARNING: Luminaire wiring and electrical parts may be

damages when installing retrot kit hardware. Check for

enclosed wiring and components.

• WARNING: Check the existing wiring for damage before

installing upgrade kit. Do not install if existing wires are

damaged. This retrot kit is accepted as a component of

a luminaire where the suitability of the combination shall

be determined by authorities having jurisdiction.

• “This luminaire has been modied and can no longer

operate the originally intended lamp,” shall be marked

on the retrot luminaire where readily visible by the user

during normal maintenance including lamping.

• Do not use with dimmers.

• Suitable for damp locations. Suitable for use in enclosed

luminaries.

• This device is not intended for use with emergency exits.

• This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing xture. Retain for future reference.

INSTALLATION: (See diagrams on back)

STEP 1: Make sure the circuit breaker that

supplies the power to the xture is turned OFF.

STEP 2: Before installation, select your preferred CCT

by moving the switches on both ends of the lamp to

either 4000K, 5000K or 6500K.

STEP 3: Remove lens or diffuser cover (if applicable).

STEP 4: Open/Remove ballast wiring compartment cover.

STEP 5: Identify the Line and Neutral wires running power

is OFF using a voltmeter.

STEP 6: Cut all wires connected to the ballast, and

remove ballast (and starter if present). Dispose of ballast

and uorescent lamps in accordance with government

regulations in your area.

STEP 7: Ensure that the xture contains R17d lamp holders.

STEP 8: These T8 LED lamps are designed for single

ended wiring (Figure 1) and double-ended wiring

(Figure 1a). When installing, conrm only the input end

Figure 2: Retrot with TWO Lamps

Figure 4: Retrot with THREE/FOUR Lamps +

TWO Ballasts

Figure 3: Retrot with THREE/FOUR Lamps

Figure 1: Retrot with ONE Lamp

Single-ended connection (non-shunted sockets)

Double-ended connection (shunted or non-shunted sockets)

Figure 2a: Retrot with TWO Lamps

Figure 4a: Retrot with THREE/FOUR Lamps +

TWO Ballasts

Figure 3a: Retrot with THREE/FOUR Lamps

Figure 1a: Retrot with ONE Lamp

Produkt Specifikationer

Mærke:	Satco
Kategori:	overvåge
Model:	S16434

Har du brug for hjælp?

Hvis du har brug for hjælp til Satco S16434 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

overvåge Satco Manualer

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

overvåge Manualer

Nyeste overvåge Manualer

BenQ DesignVue PD2730S Manual

8 April 2025

Asus VA279QGS Manual

8 April 2025

Acer EV227Q Manual

8 April 2025

BenQ PD3226G Manual

7 April 2025

Philips 221V8LB Manual

4 April 2025

Extron TLS 1025M Manual

2 April 2025

PureTools PT-SCREEN-100 Manual

1 April 2025

Viewsonic VG2752-2K Manual

30 Marts 2025

Cooler Master GM27QPA Manual

28 Marts 2025

MSI MAG 242C Manual

28 Marts 2025