Genelec 7370A Manual

Genelec Skærm 7370A

Læs gratis den danske manual til Genelec 7370A (8 sider) i kategorien Skærm. Denne vejledning er vurderet som hjælpsom af 73 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 37 anmeldelser. Har du et spørgsmål om Genelec 7370A, eller vil du spørge andre brugere om produktet?

Side 1/8
Genelec 7360A and 7370A
Smart Active Subwoofers
Operating Manual
7300 Series
750-7360A/7370A
Genelec 7360A and 7370A Smart Active Subwoofers
Introduction
Congratulations and a thank-you for the
purchase of this Genelec 7300 series
subwoofer. This manual addresses setting
up and using the Genelec 7360A and 7370A
subwoofers. These subwoofers are designed
to integrate easily into all environments, both
those using analogue audio as well as those
using digital AES/EBU audio. Genelec 7360A
and 7370A subwoofers are designed for
precise monitoring of multichannel analogue
audio signals and stereo AES/EBU signals.
Multichannel AES/EBU signal can be
monitored by using the 9301A multichannel
digital audio interface device connected to
the subwoofer.
Energy saving Intelligent Signal Sensing
(ISS) can be turned on to put the subwoofer
automatically into a standby state when
audio signal has been absent for a selected
time. In the standby mode the product
consumes less than one Watt of power.
Upon sensing an input signal the subwoofer
automatically wakes up to full operation. The
wait until entering the ISS power save can be
congured using the Genelec Loudspeaker
Manager (GLM) software. When the ISS is
active you can have your monitoring system
ready for action at all times.
Installation
Each subwoofer is supplied with a mains
cable, one 5 m GLM network cable and an
operating manual. Before connecting switch
the subwoofer and monitors o.
Connections
Analogue input 1 thru 7
XLR balanced inputs, typically provided from
console or monitor controller. +24 dBu max.
Multichannel digital signal can be
monitored by using the 9301A AES/EBU
Multichannel Interface device connected to
the subwoofer.
LFE In
This is a dedicated input for LFE use with
analogue signals. Its bandwidth is extended
to 150 Hz. The addition of +10 dB is enabled
by the +10 dB DIP Switch.
Analogue Output 1 thru 7
Balanced XLR connectors for connecting the
main monitors to the subwoofer. Depending
on the chosen mode of bass management,
these outputs may carry either unltered or
high-pass ltered signal to the main monitors.
See chapter "Bass Management" for details.
LFE Out
Straight thru-put of the LFE In. Typically LFE
Out will be connected to LFE In when daisy-
chaining multiple subwoofers.
Link Out
Combined summation of main inputs 1 thru
7 that are passed along to a second or more
daisy-chained subwoofers. See chapter
"Using Multiple Subwoofers."
Link In
Use this input when daisy-chaining
subwoofers. Accepts ONLY the signal from
Link Out. Analogue inputs 1-7 should not be
used when Link In is connected. See chapter
"Using Multiple Subwoofers."
OUT1 / Test 1
Passes the 85 Hz Phase Test Tone when used
in the Stand Alone Manual Mode. Enabled
with the Dip Switch labeled "Test Tone".
OUT2/Test 2
Reserved for future use.
AES/EBU IN
Two channel AES/EBU digital input. This
input can also be congured to receive a
digital LFE channel using the GLM software
or the "Digital LFE" and "LFE Channel A/B"
switches.
AES/EBU OUT
Output is straight thru-put of AES/EBU IN.
BYPASS
Bass manager subwoofer Bypass. For use
with Stand-alone Manual mode. Accepts a
TRS/TS contact open/close device.
GLM NETWORK
Two CAT5 (RJ45) GLM Network connectors
for computer control using the Genelec
Loudspeaker Manager (GLM) software.
MAINS INPUT
Supports a wide mains voltage range
(100-240 VAC, 50-60 Hz) and enables the
subwoofer to be plugged in anywhere
globally. If the mains power is provided with
a generator, inverter or certain lower-quality
UPS devices, we recommend ltering of the
mains power voltage harmonics and taking
care that the voltage supply is stable.
Bass Management
Bass management splits the signal from each
input into low and high frequency components.
Signal content below the crossover frequency
is reproduced by the subwoofer and signal
content above the crossover frequency is
reproduced by the monitors connected to the
outputs of the subwoofer.
The 736
0A and 7370A offer two bass
management methods:
Centralized bass management
This method builds both the highpass and
the lowpass lters in the subwoofer and can
be used in all setups, with or without GLM
control. A xed 85 Hz crossover lter for the
analogue main channels is default for manual
stand-alone use. However, we recommend
the use of the much more exible distributed
bass management method.
In this method all analogue signal cables
are routed through the subwoofer's IN/OUT
connectors to the respective main monitors.
Distributed bass management
In this method the lowpass lter is applied
in the subwoofer and the highpass lter in
the monitor, and these are set in synchrony
using the GLM network. This method is only
available in systems where GLM is used.
The GLM management software enables
adjusting the subwoofer/monitor crossover
from 50 Hz to 100 Hz when distributed bass
management is used.
The distributed bass management
supports three different signal cabling
congurations:
All channels routed through the
subwoofer's IN/OUT connectors to the
respective monitors.


Produkt Specifikationer

Mærke: Genelec
Kategori: Skærm
Model: 7370A

Har du brug for hjælp?

Hvis du har brug for hjælp til Genelec 7370A stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skærm Genelec Manualer

Genelec

Genelec 7382AP Manual

9 Januar 2024
Genelec

Genelec 1238AC Manual

15 December 2023
Genelec

Genelec 4010A Manual

24 September 2023
Genelec

Genelec 4430A Manual

11 September 2023
Genelec

Genelec 8331 Manual

19 December 2022
Genelec

Genelec 1032C Manual

3 December 2022
Genelec

Genelec 8351B Manual

15 November 2022
Genelec

Genelec 4040A Manual

13 November 2022
Genelec

Genelec 8350A Manual

13 November 2022
Genelec

Genelec 8340A Manual

7 November 2022

Skærm Manualer

Nyeste Skærm Manualer