Generac RTSN800K3 Manual

Generac bryter RTSN800K3

Læs gratis den danske manual til Generac RTSN800K3 (18 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Generac RTSN800K3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/18

Owner's Manual

600 and 800 Amp RTS Automatic Transfer Switch

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all-inclusive. If

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or operating

technique chosen does not render the transfer switch unsafe.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or care-

lessly. Observe them carefully. Their definitions are as follows:

After this heading, read instructions that, if not

strictly complied with, will result in serious

personal injury, including death.

After this heading, read instructions that, if not

strictly complied with, could result in serious

personal injury, including death.

After this heading, read instructions that, if not

strictly complied with, might result in minor or

moderate injury.

NOTE:

After this heading, read instructions that, if not strictly complied

with, may result in damage to equipment and/or property.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the service are essential to prevent-

ing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property.



This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

GENERAL HAZARDS

• Any AC generator that is used for backup power if a NORMAL

(UTILITY) power source failure occurs, must be isolated from

the NORMAL (UTILITY) power source by means of an approved

transfer switch. Failure to properly isolate the NORMAL and

STANDBY power sources from each other may result in injury

or death to electric utility workers, due to backfeed of electrical

energy.

• Improper or unauthorized installation, operation, service or

repair of the equipment is extremely dangerous and may result

in death, serious personal injury, or damage to equipment and/

or personal property.

• Extremely high and dangerous power voltages are present inside

an installed transfer switch. Any contact with high voltage ter-

minals, contacts or wires will result in extremely hazardous,

and possibly LETHAL, electric shock. DO NOT WORK ON THE

TRANSFER SWITCH UNTIL ALL POWER VOLTAGE SUPPLIES

TO THE SWITCH HAVE BEEN POSITIVELY TURNED OFF.

• Competent, qualified personnel should install, operate and ser-

vice this equipment. Adhere strictly to local, state and national

electrical and building codes. When using this equipment,

comply with regulations the National Electrical Code (NEC),

CSA Standard; C22.1 Canadian Electric Code and Occupational

Safety and Health Administration (OSHA) have established.

• Never handle any kind of electrical device while stand-

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• Remove all jewelry (such as rings, watches, bracelets, etc.)

before working on this equipment.



SAVE THESE INSTRUCTIONS! Read the following information carefully before attempting to install,

operate or service this equipment. Also read the instructions and information on tags, decals, and

labels that may be affixed to the transfer switch. Replace any decal or label that is no longer legible.



DANGER! Connection of a generator to an electrical system normally supplied by an electric util-

ity shall be by means of suitable transfer equipment so as to isolate the electric system from utility

distribution system when the generator is operating (Article 701 Legally Required Standby Systems

or Article 702 Optional Standby Systems, as applicable). Failure to isolate electric system by these

means may result in damage to generator and may result in injury or death to utility workers due to

backfeed of electrical energy.

Safety Rules

Produkt Specifikationer

Mærke:	Generac
Kategori:	bryter
Model:	RTSN800K3

Har du brug for hjælp?

Hvis du har brug for hjælp til Generac RTSN800K3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter Generac Manualer

Generac RXSW100A3SPD Manual

23 August 2025

Generac RTSN800G3 Manual

22 August 2025

Generac RTSN800K3 Manual

22 August 2025

Generac RXSW200A3SPD Manual

22 August 2025

Generac RXSC200A3 Manual

21 Juli 2025

bryter Manualer

Nyeste bryter Manualer

Netgear GSM4230P Manual

23 August 2025

Netgear GSM4212UX Manual

23 August 2025

Netgear GSM4212PX Manual

22 August 2025

Netgear GSM4230PX Manual

22 August 2025

Netgear GSM4248PX Manual

22 August 2025

Netgear M4300-24X Manual

22 August 2025

Netgear M4300-12X12F Manual

22 August 2025

Eberle DÄ 565 28 Manual

22 August 2025

Digitus DS-72220-2CH Manual

22 August 2025

Digitus DS-72220-1UK Manual

22 August 2025