Gigabyte GA-6ETXDR Manual

Gigabyte Bundkort GA-6ETXDR

Læs nedenfor 📖 manual på dansk for Gigabyte GA-6ETXDR (76 sider) i kategorien Bundkort. Denne guide var nyttig for 24 personer og blev bedømt med 4.8 stjerner i gennemsnit af 12.5 brugere

Download PDF

Side 1/76

FCC Compliance Statement:

This equipment has been tested and found to

comply with limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable

protection against harmful interference in

residential installations. This equipment

generates, uses, and can radiate radio

frequency energy, and if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause interference to radio or

television equipment reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Move the equipment away from the receiver

-Plug the equipment into an outlet on a circuit different from that to which

the receiver is connected

-Consult the dealer or an experienced radio/television technician for

additional suggestions

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void Your

authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subjected to

the following two conditions 1) this device may not cause harmful interference

and 2) this device must accept any interference received, including interference

that may cause undesired operation.

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name: G.B.T. INC.

Address: 18305 Valley Blvd., Suite#A

LA Puent, CA 91744

Phone/Fax No: (818) 854- -9338/ (818) 854 9 3 3 9

hereby declares that the product

Product Name:

Model Number:

Mother Board

Conforms to the following specifications:

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

Supplementary Informati on:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful

and (2) this device must accept any inference received, including

that may cause undesired operation.

Representative Person's Name: ERIC LU

Signature:

Date: May. 20, 2001

Eric Lu

GA-6EXDR

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-6ETXDR

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

EN 55011 Limits and methods of measurement EN 61000- -3 2* Disturbances in supply systems caused

of radio disturbance characteristics of EN60555-2 by household appliances and similar

industrial, scientific and medical (ISM electrical equipment “Harmonics”

high frequency equipment

EN55013 Limits and methods of measurement EN61000- -3 3* Disturbances in supply systems caused

of radio disturbance characteristics of EN60555-3 by household appliances and similar

broadcast receivers and associated electrical equipment “Voltage fluctuations”

equipment

EN 55014 Limits and methods of measurement EN 50081-1 Generic emission standard Part 1:

of radio disturbance characteristics of Residual, commercial and light industry

household electrical appliances,

portable tools and similar electrical EN 50082-1 Generic immunity standard Part 1:

apparatus Residual, commercial and light industry

EN 55015 EN 55081 Limits and methods of measurement -2 Generic emission standard Part 2:

of radio disturbance characteristics of Industrial environment

fluorescent lamps and luminaries

EN 55020 Immunity from radio interference of EN 55082-2 Generic immunity standard Part 2:

broadcast receivers and associated Industrial environment

equipment

EN 55022 ENV 55104 Limits and methods of measurement Immunity requirements for household

of radio disturbance characteristics of appliances tools and similar apparatus

information technology equipment

DIN VDE 0855 Cabled distribution systems; Equipment EN 50091- 2 EMC requirements for uninterruptible

part 10 for receiving and/or distribution from power systems (UPS)

part 12 sound and television signals

CE marking (EC conformity marking)

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

EN 60065 Safety requirements for mains operated EN 60950 Safety for information technology equipment

electronic and related apparatus for including electrical business equipment

household and similar general use

EN 60335 Safety of household and similar EN 50091-1 General and Safety requirements for

electrical appliances uninterruptible power systems (UPS)

Manufacturer/Importer

Signature : Rex Lin

(Stamp) Date : May. 20, 2001 Name : Rex Lin

How This Manual Is Organized

This manual is divided into the following sections:

1) Revision History Manual revision information

2) Item Checklist Product item list

3) Features Product information & specification

4) Hardware Setup Instructions on setting up the motherboard

5) Performance & Block Diagram Product performance & block diagram

6) Advanced Networking Services

For Windows NT*4 and Windows 2000

(Teaming)

7) BIOS Setup Instructions on setting up the BIOS

software

8) Appendix General reference

Table Of Content

Revision History P.1

Item Checklist P.2

Summary of Features P.3

6ETXDR Motherboard Layout P.5

Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition

P.6

Performance List P.27

Block Diagram P.28

Advanced Networking Services for Windows NT* 4 and Windows 2000 (Teaming) P.29

Memory Installation P.35

DIMM QVL List P.35

Page Index for BIOS Setup P.37

Appendix P.63

6ETXDR Motherboard

Revision History

Revision Revision Note Date

1.0 Initial release of the 6ETXDR motherboard user’s manual. Aug. 2001

The author assumes no responsibility for any errors or omissions that may appear in this

document nor does the author make a commitment to update the information contained herein.

Third-party brands and names are the property of their respective owners.

Aug. 10, 2001 Taipei, Taiwan, R.O.C

Item Checklist

þ The 6ETXDR motherboard

þ Cable for SCSI U160 / ATA33 / Floppy device

þ Diskettes or CD (Driver CD) for motherboard driver & utility

þ 6ETXDR user’s manual

¨ Internal COM B Cable (Optional)

¨ Internal Chassis Cable (Optional)

6ETXDR Motherboard

Summary Of Features

Form Factor Ÿ 30.4 cm x 24.3 cm ATX size form factor, 6 layers PCB.

Ÿ 250 watt or higher power supply required

CPU Ÿ Dual ZIF PGA370 Socket

Supports all new PentiumIII processors (FC-PGA & FC-PGA2

package) up to 1.26GHz.

Ÿ Two onboard VRMs (VRM 8.5)

Ÿ 100/133 MHz Front Side Bus support

Chipset Ÿ ServerWorks ServerSetTMIII LE-T Chipset

Ÿ Integrated I/O APIC

Ÿ Full peer- -to peer support

Memory Ÿ Four 25° angled 168-pin DIMM sockets

Ÿ Support only 3.3V PC-100/PC133 registered 72 bit

ECC type SDRAM DIMM.

Ÿ Maximum up to 4 GB.

I/O Controller Ÿ NS PC97317VUL Super I/O Chip

Slots Ÿ Two PCI slots supports 33MHz & PCI 2.2 compliant

Ÿ Two PCI-64bit/66Mhz slots & PCI 2.2 compliant

Ÿ PCI Raiser Card (Optional)

On-Board IDE Ÿ Support for UDMA33 IDE and ATAPI compliant

devices.

Ÿ Supports for dual channel master mode and up to 4

enhance IDE devices.

On-Board SCSI Ÿ Integrated LSI SYM53C1010-66 Chipset with

64b/66MHz

Ÿ Supports dual channel Ultra160 SCSI

Ÿ 160MBps throughput and up to 15 devices per channel

Ÿ Channel A and B: 68-pin connectors

On-Board

Peripherals

Ÿ 1 floppy port supports 2 FDD with 360K, 720K, 1.2M,

1.44M and 2.88M bytes

Ÿ 1 parallel ports supports Normal/EPP/ECP mode

Ÿ 2 9-pin UART serial ports (COM 1 & COM 2)

(one serial port via cable- optional)

Ÿ 4 USB ports

On-Board VGA Ÿ Onboard Ati Rage XL PCI Accelerator

Ÿ Standard 15-pin analog VGA port

Ÿ 8MB SDRAM frame buffer

To be continued…

Summary of Features

On-Board LAN Ÿ Integrated two Intel 82559 LAN controllers

Ÿ 10/100Mbps data transfer rate per controller

Ÿ 3 pin Wake on LAN (S1 and S5 state) connector

Ÿ Adapter Fault Tolerance (AFT) and Adaptive Load

Balancing (ALB)

Hardware Monitor Ÿ CPU 1/ CPU 2 fan revolution detect

Ÿ CPU 1/ CPU 2 temperature detect

Ÿ System voltage detect

Ÿ CPU overheat shutdown detect

Ÿ 3pin fan speed monitoring headers

Ÿ 2pin chassis intrusion header

Ÿ CPU, Voltages and system temperature monitoring

Ÿ Built-in Wake on Modem header

PS/2 Connector Ÿ PS/2 Keyboard interface and PS/2 Mouse interface

BIOS Ÿ Licensed AMI BIOS, 4M bits flash ROM

Ÿ Auto configure IDE HDD type

Ÿ User setting for hardware monitoring

Ÿ DMI 2.0 compliant

Ÿ Multiple boot (Optional)

Additional Features Ÿ Support Internal / External Modem Ring On

Ÿ Poly fuse for PS/2 and USB devices over-current

protection

6ETXDR Motherboard

6ETXDR Motherboard Layout

COM2 BRIGHT

VGA COM 1

LPT

PS/2

6ETXDR

BAT1

USB

ATX Power

Floppy

IDE1

IDE2

DIMM3

DIMM2

DIMM4

DIMM1

USB2

JP4

J19

ATI

Rage

Super I/O

LAN2

Conn.

LAN1

Conn.

SW1

BZ1

PGA 370

CPU 1

PGA 370

CPU 2

RCC-NB6635

RCC-IB6566

PCI1

PCI2

64 PCI 1

64 PCI 2

LSI

LSA0723

J22

JP11

JP10

JP2

JP1

JP3

JP6

SW2

SCSI 1 SCSI 2

82559

JP12

JP9

J23

6ETXDR Motherboard Layout

Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition Page

CPU Speed Setup P.7

Connectors P.11

ATX Power P.11

COM 1 / VGA / LPT Port P.11

COM 2 Port P.12

Floppy Port P.12

IDE 1(Primary) / IDE 2(Secondary) Port P.13

J1 (CPU1 Fan) P.13

J2 (Panel Fan) P.14

J4 (Wake On LAN) P.14

J5 (Ring Power On) P.15

J6 (CPU2 Fan) P.15

J7 (Power Fan1) P.16

J19 (System Interface Connector) P.16

J22 (Power Fan2) P.17

LAN connector P.17

PS/2 Keyboard & PS/2 Mouse Connector P.18

SCSI1 (Primary)/SCSI2 (Secondary) P.18

USB1( USB 1 Connector) P.19

USB2(Front USB Connector) P.19

J23 (SMBUS Connector) P.20

Panel and Jumper Definition P.21

J3 (2x11 Pins Jumper) P.21

JP1 (Firmware White Protect) P.22

JP2 (VGA Enable Jumper) P.22

JP3 (SCSI Enable Jumper) P.23

JP4 (SCSI TERM A) P.23

JP6 (SCSI TERM B) P.24

JP10 (LAN1 Enable Selection) P.24

JP11 (LAN2 Enable Selection) P.25

JP12 (Case Open) P.25

SW2 (Pole1_On Password Enable / Pole4_On CMOS Clear) P.26

BAT1 (Battery) P.26

6ETXDR Motherboard

CPU Speed Setup

The system bus speed is depended on CPU. (Supported 100,133MHz). The user can change

the DIP switch (SW1) and Jumper (JP9) selection to set up the CPU speed for 600MHz – 1GHz

processor.

The CPU speed must match with the frequency ratio. It will cause system hanging up if

the frequency ratio is higher than that of CPU.

SW1:

DIP SWITCH FREQ. RATIO

1 2 3 4

X3 O X O O

X3.5 X X O O

X4 O O X O

X4.5 X O X O

X5 O X X O

X5.5 X X X O

X6 O O O X

X6.5 X O O X

X7 O X O X

X7.5 X X O X

X8 O O X X

X8.5 O X O O

X9 X X O O

X9.5 X O O O

X10 X O X X

X10.5 O O X O

X11 O X X X

X11.5 X O X O

X12 O X X O

X13 X X X O

X14 O O O X

X15 X O O X

X16 O X O X

For double CPU use, the same CPU must be used in CPU socket 1 and socket 2.

(The same stepping, FSB, ratio)

Intel Processor all have locked Frequency Multiple, so you can not change the CPU

Frequency Multiple.

CPU Speed Setup

1. Pentium !!! 600/100MHz FSB

Pentium !!! 800/133MHz FSB

SW2

SW1

1 2 3 4

You can change the DIP switch

(SW1) selection to set up the CPU

Speed.

The CPU frequency RATIO is 6.

The FSB is 100MHz, than CPU

speed is 600MHz.

The FSB is 133MHz, than CPU

Speed is 800MHz.

JP9

1-2close

100 MHz

2-3close

Auto

(Default)

JP9

2. Pentium !!! 650/100MHz FSB

Pentium !!! 866/133MHz FSB

SW2

SW1

1 2 3 4

3. Pentium !!! 700/100MHz FSB

Pentium !!! 933/133MHz FSB

SW2

SW1

1 2 3 4

6ETXDR Motherboard

4. Pentium !!! 750/100MHz FSB

Pentium !!! 1GHz/133MHz FSB

SW2

SW1

1 2 3 4

5. Pentium !!! 800/100MHz FSB

Pentium !!! 1.06GHz/133MHz FSB

SW2

SW1

1 2 3 4

6. Pentium !!! 850/100MHz FSB

Pentium !!! 1.13GHz/133MHz FSB

SW2

SW1

1 2 3 4

CPU Speed Setup

7. Pentium !!! 1.2GHz/133MHz FSB

SW2

SW1

1 2 3 4

8. Pentium !!! 1.26GHz/133MHz FSB

SW2

SW1

1 2 3 4

9. Pentium !!! 533/133MHz FSB

SW2

SW1

1 2 3 4

10. Pentium !!! 600/133MHz FSB

SW2

SW1

1 2 3 4

6ETXDR Motherboard

Connectors

ATX Power

Pin No. Definition

3,5,7,13,

15 17- GND

1,2,11 3.3V

4,6,19,20 VCC

10 +12V

12 -12V

18 -5V

8 Power Good

9 5V SB stand by+5V

14 PS-ON(Soft On/Off)

Please note:

AC power cord should only be connected to your power supply unit after

ATX power cable and other related devices are firmly connected to the

mainboard.

COM 1 / VGA / LPT Port

COM 1

LPT PORT

VGA

Please note:

This mainboard supports 1 standard COM port ,1 VGA port and 1 LPT

port. Device like printer can be connected to LPT port ; mouse and

modem etc can be connected to COM ports.

Connectors

COM 2 Port

COM 2

FDD 1 : Floppy Port

Red Line

FDD1

6ETXDR Motherboard

IDE1 (Primary), IDE2 (Secondary) Port

IDE1 IDE2

Red Line

J1 : CPU1 Fan

Pin No. Definition

1 Control

2 +12V

3 SENSE

Connectors

J2 : Panel Fan

Pin No. Definition

1 Control

2 +12V

3 SENSE

J4 : Wake On LAN

Pin No. Definition

1 +5V SB

2 GND

3 Signal

Connectors

J7 : Power Fan 1

Pin No. Definition

1 Control

2 +12V

3 SENSE

J19 : System Interface Connector

J19

6ETXDR Motherboard

J22 : Power Fan 2

Pin No. Definition

1 Control

2 +12V

3 SENSE

LAN Connector

(LAN Active LED)

1 – Yellow LED

(LAN Active LED)

LAN2 LAN1

2 – Green LED

(LAN Link LED)

100Mb--Light

10 Mb--Blind

Connectors

PS/2 Keyboard & PS/2 Mouse Connector

PS/2

Mouse / Keyboard

Pin No. Definition

1 Data

2 NC

3 GND

4 Power

5 Clock

6 NC

PS/2 Keyboard

PS/2 Mouse

1 2

Please note:

This mainboard supports standard PS/2 keyboard and PS/2 mouse interface

connector.

SCSI 1 (Primary), SCSI 2 (Secondary) Port

SCSI Port

6ETXDR Motherboard

USB1: USB 1 Connector

Pin No. Definition

1 USB V0

2 USB D0-

3 USB D0+

4 GND

5 USB V1

6 USB D1-

7 USB D1+

8 GND

5 6 7 8

3 2 1

Please note:

Before you connect your device(s) into USB connector(s), please make

sure your device(s) has a standard USB interface like, USB keyboard,

mouse, scanner, zip, buzzer… Also make sure your OS supports USB

controlle

r (Win 95 w/ USB supperment, Win98, Windows 2000, Windows

ME, Win NT w/ SP 6). If your OS does not support USB controller,

please contact OS vendor for passible patch or driver upgrade. For more

information please contact your OS or device(s) vendors.

USB2 : Front USB Connector

Pin No. Definition

1 5V-SB

2 GND

3 USB D2-

4 NC

5 USB D2+

6 USB D3+

7 NC

8 USB D3-

9 GND

10 5V-SB

2 10

Please note:

Be careful with the polarity of the front panel USB connector. Check the pin

assignment while you connect the front panel USB cable. Please contact your

nearest dealer for optional front panel USB cable.

Connectors

J23 : SMBUS Connector

Pin No.

Definition

1 VCC

2 SDA

3 SCL

4 NC

5 GND

6ETXDR Motherboard

Panel And Jumper Definition

J3 : 2x11 Pins Jumper

GD PW P+ P− P−

S P K

GN (Green Switch) Open: Normal Operation

Close: Entering Green Mode

GD (Green LED) Pin 1: LED anode(+)

Pin 2: LED cathode(−)

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)

Pin 2: LED cathode(−)

SPK (Speaker Connector) Pin 1: VCC(+)

Pin 2- Pin 3: NC

Pin 4: Data(−)

RE (Reset Switch) Open: Normal Operation

Close: Reset Hardware System

P+P−P−(Power LED) Pin 1: LED anode(+)

Pin 2: LED cathode(−)

Pin 3: LED cathode(−)

PW (Soft Power Connector) Open: Normal Operation

Close: Power On/Off

Please note:

Please connect the power LED, PC speaker, reset switch and power switch etc of

your chassis front panel to the front panel jumper according to the pin assignment

above.

Panel and Jumper Definition

JP1 : Fireware Write Protect

Enable

Pin No. Definition

2-3 close Disable (Default)

1-2 close Enable

Please note:

To flash/upgrade BIOS on this MB JP1 must be Enabled. We recommend

JP1 to be set to “ ”Disabled , whenever

user is not try to flash/upgrade the

BIOS.

Disable

(Default)

JP2 : VGA Enable jumper

Pin No. Definition

1-2 close Onboard VGA

Enable (Default)

2-3 close Onboard VGA

Disable

Disabled

Enabled

(Default)

6ETXDR Motherboard

JP3 : SCSI Enable jumper

Pin No. Definition

1 2- close Onboard SCSI

Enable (Default)

2 3- close Onboard SCSI

Disable

Disabled

Enabled

(Default)

JP4 : SCSI TERM A

Pin No. Definition

Close Enable (Default)

Open Disable

Enable

(Default)

Disable

JP4

Panel and Jumper Definition

JP6 : SCSI TERM B

Pin No. Definition

Close Enable (Default)

Open Disable

Enable

(Default)

Disable

JP6

JP10 : LAN1 Enable Selection

Pin No. Definition

1-2

close Onboard LAN1

Enabled (Default)

2-3

close Onboard LAN1

Disabled

Enabled

(Default)

6ETXDR Motherboard

JP11 : LAN2 Enable Selection

Pin No. Definition

1-2 close Onboard LAN2

Enabled (Default)

2-3 close Onboard LAN2

Disabled

Enabled

(Default)

JP12 : Case Open

Pin No.

Definition

1 Signal

2 GND

Panel and Jumper Definition

SW2 : Pole1_ON Password Enable/ Pole4_ON CMOS Clear

Pin No. Definition

Pole4_Off CMOS Clear

Pole3_ON NC

Pole2_ON NC

Pole1_ON Password Enable

SW2

1 2 3 4

BAT1 : Battery

CAUTION

Danger of explosion if battery

is incorrectly replaced.

Replace only with the same or

equivalent type recommended

by the manufacturer.

Dispose of used batteries

according to the manufacturer’s

instructions.

6ETXDR Motherboard

Performance List

The following performance data list is the testing results of some popular benchmark testing

programs.

These data are just referred by users, and there is no responsibility for different testing data

values gotten by users. (The different Hardware & Software configuration will result in different

benchmark testing results.)

• CPU Intel Socket

370 Pentium® III 1G Hz x 2 processor

• DRAM (128 x 1)MB SDRAM (Micro MT48LC16M4A2-75)

• CACHE SIZE 256KB include in CPU (Intel Pentium® III)

• DISPLAY Onboard ATI Rage XL

• STORAGE Onboard SCSI (Seagate ST39204LW 9GB)

• O.S. Windows 2000 + SP1

• DRIVER Display Driver at 1024x768x16bitx75MHz

Processor Intel Pentium® III Socket 370

1G Hz x 2 (133x7.5)

Winbench99 (ver.1.2g)

Business Disk 6230

Hi-End Disk 18500

Business Graphics 137

Hi-End Graphics 456

Winstone2001

Business Winstone 37.1

Content Creation Winstone 41.3

6ETXDR Motherboard

Advanced Networking Services for Windows NT* 4 and

Windows 2000 (Teaming)

MPlease make sure the Intel LAN Adapter teaming driver Install complete.

(F refer to page 62)

1. Intel LAN Adapter Teaming

Adapter Teaming Installation Notes for the PRO/100 S Server Adapter Under Windows NT

4.0 and Windows 2000.

Note: Teaming requires Intel® Server Adapters.

1.1 Overview

The PRO/100 S adapter provides several options for increasing throughput and fault

tolerance when running Windows NT 4.0 or Windows 2000 :

• Adapter Fault Tolerance (AFT) - provides automatic redundancy for your adapter. If

the primary adapter fails, the secondary takes over.

• Adaptive Load Balancing (ALB) - creates a team of 2 - 8 adapters to increase

transmission throughput. Also includes the AFT option. Works with any

100BASE-TX switch.

• Fast EtherChannel* (FEC) - creates a team of 2 or 4 adapters to increase

transmission and reception throughput. Also includes the AFT option. Requires a

Cisco switch with FEC capability.

1.2 Before You Get Started

Before you can configure the PRO/100 S adapter for Adapter Teaming, you need to do the

following:

• Install at least two PRO/100+ or PRO/100 S server adapters in a Windows NT 4.0 or

Windows 2000 system. When installation is complete make sure you restart

Windows.

Note: Windows NT 4.0 Service Pack 5 or later is required for implementing Adapter

Teaming properly. Install Service Pack prior to configuring Adapter Teaming.

• If connecting to a hub, each adapter in a team must be connected to a port which is

in the same collision domain. If connected to a switch, each adapter in a team must

be connected to a port which is in the same network.

Advanced Networking Services

2. Adapter Fault Tolerance (AFT)

2.1 OverView

A method of safeguarding the network link to the server switch or network service using

transparent backup links. Adapter Fault Tolerance (AFT) requires two adapters and an

intelligent software agent that continuously monitors both links. If any component of one

link fails, the redundant link takes over within seconds— typically, without users (connected

via a hub or switch) even noticing the exchange.

2.2 Performance

To increase server availability, the server communicates with the LAN via a primary

adapter. If the primary link fails, traffic is automatically re-routed to the secondary adapter

with no interruption of service.

2.3 Manageability

Generates alert when an adapter fails. This allows any problems with links to be fixed

promptly. These alerts are operating system-based for compatibility with management

applications such as Intel® LANDesk® Server Manager which can detect the alert and

trigger an action (email, page, call).

6ETXDR Motherboard

3. Adaptive Load Balancing (ALB)

3.1 Overview

Also known as asymmetric port aggregation — is a method of ensuring consistent high

server throughput and transparent backup connections by using multiple network interface

cards and balancing the data transmissions across them. As many as four Intel® server

adapters, connected to a switch, can be configured to work together as a "team" for an

aggregate throughput of up to 400Mbps with Fast Ethernet adapters or 8Gbps with Gigabit

Ethernet Adapters.

3.2 Performance

In ALB, an intelligent adaptive agent, provided in the driver, dynamically manages the

server adapter team and evenly distributes the load among them by constantly analyzing

the traffic flow from the server. In addition, four Fast Ethernet server adapters teamed with

a switch can be configured for up to 400 Mbps bandwidth, or 8Gbps with Gigabit Ethernet

adapters.

3.3 Manageability

A single network address is assigned to the collection of adapters that constitute the ALB.

Aggregation team so that you no longer have to spend time segmenting the network to

reduce server bottlenecks.

6ETXDR Motherboard

3. At the Teaming Wizard dialog, select the type of team you want to create and click Next.

4. Add a check in the checkbox for each adapter you want as a part of the team and click

Next.

Advanced Networking Services

5. Click OK to close PROSet. II

You should notice a new listing in the Network control panel, which is the team you have

created.

6. After the team created, a Intel® Advanced Network Services Virtual Adapter will appear

on Network in the Control Panel. Assign a IP for this Virtual Adapter.

6ETXDR Motherboard

Memory Installation

The motherboard has 4 dual inline memory module (DIMM) sockets. The BIOS will automatically

detects memory type and size. To install the memory module, just push it vertically into the

DIMM Slot .The DIMM module can only fit in one direction due to the two notch. Memory size

can vary between sockets.

Install memory in any combination table:

DIMM 168-pin SDRAM DIMM Modules

DIMM 1 Supports 16 / 32 / 64 / 128 / 256 / 512 MB / 1GHz X 1 pcs

DIMM 2 Supports 16 / 32 / 64 / 128 / 256 / 512 MB / 1GHz X 1 pcs

DIMM 3 Supports 16 / 32 / 64 / 128 / 256 / 512 MB / 1GHz X 1 pcs

DIMM 4 Supports 16 / 32 / 64 / 128 / 256 / 512 MB / 1GHz X 1 pcs

★Total System Memory (Max 4GB)

DIMM QVL List

Vender Type

Module

Size

Chip

Size

Vender

P/N

Chips

vender Chip P/N Result

TwinMOS

PC133 Reg ECC

256MB

16M×8

039MDS102300028 TwinMOS TMS3808B4E -6 Pass

SMART PC133 Reg ECC

128MB 16M×4

SM572164574E63R Infineon HYB39S64400CT Pass

SMART PC133 Reg ECC

256MB 32M×4

SM572324574E03R SAMSUNG

K4S280432B-TC75

Pass

SMART PC133 Reg ECC

512MB 64M×4

SM572644578E63R SAMSUNG

K4S560432A-TC75

Pass

SMART PC133 Reg ECC

1024MB

SM572284578E83R IBM Pass

ATP PC133 Reg ECC

128MB 16M×4

AR16V72C4S4GAS SAMSUNG

K4S640432D-TC75

Pass

ATP PC133 Reg ECC

128MB 16M×8

AR16V72L8S4GAS SAMSUNG

K4S280823B-TC75

Pass

ATP PC133 Reg ECC

256MB 32M×4

AR32V72C4S4GAS SAMSUNG

K4S280432B-TC75

Pass

ATP PC133 Reg ECC

512MB 64M×4

AR64V72N4S8GAS SAMSUNG

K4S560432A-TC75

Pass

ATP PC133 Reg ECC

512MB 64M×4

AR64V72C4S8GAS SAMSUNG

K4S560432A-TC75

Pass

ATP PC133 Reg ECC

1024MB

64M×4

AR128V72C4SSGAS SAMSUNG

K4S560432A-TC75

Pass

ATP PC133 Reg ECC

1024MB

64M×4

AR128V72J4SGAS SAMSUNG

Pass

Micron PC133 Reg ECC

256MB 32M×4

MT18LSDT3272G-

133B1 Micron MT48LC32M4A2-75 Pass

Micron PC133 Reg ECC

128MB 16M×4

MT18LSDT1672G-

133C2 Micron MT48LC16M4A2-75 Pass

NEC PC133 Reg ECC

256MB 32M×4

MC- -4532DA727EF

A75 NEC

D45128441G5- -A75

9JF Pass

HITACHI PC133 Reg ECC

512MB 64M×4

HB52F649E1-75B HITACHI 5225405BTT75 Pass

APACER

PC133 Reg ECC

128MB 8M×8

71.7335 2.114

(phase out) Infineon

HYB39S64800CT-

7.5 Pass

APACER

PC133 Reg ECC

128MB 16M×8

71.74352.111 Infineon

HYB39S128800CT-

7.5 Pass

APACER

PC133 Reg ECC

256MB 32M×4

71.85252.112 Infineon

HYB39S128400CT-

7.5 Pass

BIOS Setup

Vender Type

Module

Size

Chip

Size

Vender

P/N

Chips

vender Chip P/N Result

APACER

PC133 Reg ECC

512MB 64M×4

71.96252.462 SAMSUNG

K4S560432A-TC75

Pass

PANRAM

PC133 Reg ECC

512MB 32M×8

168SD512M338,WB,

BR10 Winbond W982508BH-75 Pass

PANRAM

PC133 Reg ECC

256MB 16M×8

168SD256M3,WB,

ERB Winbond W981208BH-75 Pass

PANRAM

PC133 Reg ECC

128MB 16M×8

168SD128M38,WB,

ERB Winbond W981208BH-75 Pass

Samsung

PC133 Reg ECC

128MB 16M×4

M390S1620DT1-C75 SAMSUNG

K4S280432A-TC75

Pass

Samsung

PC133 Reg ECC

256MB 32M×4

M390S3320AT1-C75 SAMSUNG

K4S640432D-TC75

Pass

Samsung

PC133 Reg ECC

512MB 64M×4

M390S6450BT1-C75 SAMSUNG

Pass

6ETXDR Motherboard

$ Page Index for BIOS Setup Page

Main P.39

Advanced P.41

Chipset P.52

PCIPnP P.54

Power P.55

Boot P.56

Security P.57

Exit P.62

BIOS Setup

BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to

modify the basic system configuration. This type of information is stored in battery-backed

CMOS RAM so that it retains the Setup information when the power is turned off.

ENTERING SETUP

Power ON the computer and press <Del> immediately will allow you to enter Setup. If the

message disappears before you respond and you still wish to enter Setup, restart the system to

try again by turning it OFF then ON or pressing the "RESET" bottom on the system case. You

may also restart by simultaneously press <Ctrl> − <Alt>− <Del> keys.

CONTROL KEYS

< >↑ Move to previous item

< >↓ Move to next item

< >← Move to the item in the left hand

< >→ Move to the item in the right hand

<Esc> Main Menu - Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu - Exit current page

and return to Main Menu

<+/PgUp> Increase the numeric value or make changes

<-/PgDn> Decrease the numeric value or make changes

<F1> General help, only for Status Page Setup Menu and Option Page Setup

<F2> Reserved

<F3> Reserved

<F4> Reserved

<F5> Reserved

<F6> Reserved

<F7> Discard Changes

<F8> Load Failsafe Defaults

<F9> Load Optional Defaults

<F10> Save all the CMOS changes, only for Main Menu

6ETXDR Motherboard

GETTING HELP

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu / Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the

possible selections for the highlighted item. To exit the Help Window press <Esc>.

Main

Once you enter AMI BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the

screen. The Main Menu allows you to select from eight setup functions and one exit choices.

Use arrow keys to select among the items and press <Enter> to accept or enter the sub-screen.

Figure 1: Main

•

Main

This setup page includes all the items in standard compatible BIOS.

•

Advanced

This setup page includes all the items of AMI special enhanced features.

(ex: Auto detect fan and temperature status, automatically configure hard disk

parameters.)

BIOS SETUP UTILITY

Main Advanced Chipset PCIPnP Power Boot Security Exit

AMIBIOS Version : 07.00.xx

BIOS Build Date : 02/07/01

BIOS ID : GA6ETXDR0

Processor Type : PentiumIII™

Processor Speed : 800MHz

System Memory : 512MB

System Time

[14:23:47]

System Date

[Mon 02/19/2001] ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

BIOS Setup

•

Chipset

This setup page includes all the items of chipset special features.

•

PCIPnP

This setup page includes all the configurations of PCI & PnP ISA resources.

•

Power

This setup page includes all the items of Green function features.

•

Boot

This setup page includes all the items of first boot function features.

•

Security

Change, set, or disable password. It allows you to limit access to the system and Setup,

or just to Setup.

•

Exit

Save CMOS value settings to CMOS and exit setup or abandon all CMOS value changes

and exit setup.

•

System Time & Date

The times format in <hour> <minute> <second>. The time is calculated base on the

24-hour military-time clock. For example, 1 p.m. is 13:00:00.

The date format is <Week> <Month> <Day>, <Year>.

Week The week, from Sun to Sat, determined by the BIOS and is display-only

Month The month, Jan. Through Dec.

Day The day, from 1 to 31 (or the maximum allowed in the month)

Year The year, from 1990 through 2099

6ETXDR Motherboard

Advanced

Figure 2: Advanced

Figure 2 -1: Advanced

BIOS SETUP UTILITY

Main Advanced Chipset PCIPnP Power Boot Security Exit

Setup Warning

Setting items on this screen to incorrect values may

cause the system to malfunction!

4Standard Boot Settings

4SuperIO Configuration

4Floppy Configuration

4IDE Configuration

4Event Log Configuration

4System Health Monitoring Hardware

4Remote Access Configuration ß à Select Screen

á â Select Item

Enter Go To Sub Screen

F1 General Help

F10 Save and Exit

ESC Exit

BIOS SETUP UTILITY

Advanced

Standard Boot Settings

Quick Boot [Enabled]

Bootup Num-Lock [On]

PS/2 Mouse Support [Enabled]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

BIOS Setup

•

Quick Boot

Disabled Disabled Quick Boot Function.

Enabled Enabled Quick Boot Function. (Default Value)

•

Boot Up Num-Lock

On Keypad is number keys. (Default Value)

Off Keypad is arrow keys.

•

PS/2 Mouse Support

Enabled Enabled PS/2 Mouse Support. (Default Value)

Disabled Disabled PS/2 Mouse Support.

Figure 2-2: Advanced

SuperIO Chipset Nat317

Advanced

Configure Nat317 Serial Port(s) and Parallel Port

Serial Port1 Address [3F8]

Serial Port1 Irq [4]

Serial Port2 Address [2F8]

Serial Port2 Irq [3]

Parallel Port Address [378]

Parallel Port IRQ [7]

Parallel Port Mode [ECP]

ECP Mode DMA Channel [3]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

6ETXDR Motherboard

•

Serial Port 1 Address

3F8 Enable onboard Serial port 1 and address is 3F8. (Default Value)

2F8 Enable onboard Serial port 1 and address is 2F8.

3E8 Enable onboard Serial port 1 and address is 3E8.

2E8 Enable onboard Serial port 1 and address is 2E8.

Disabled Disable onboard Serial port 1.

•

Serial Port 1 Irq

Disabled Disabled Serial Port1 Irq.

3 Set Serial Port1 Irq is 3.

4 Set Serial Port1 Irq is 4. (Default Value)

•

Serial Port 2 Address

2F8 Enable onboard Serial port 2 and address is 2F8. (Default Value)

3F8 Enable onboard Serial port 2 and address is 3F8.

3E8 Enable onBoard Serial port 2 and address is 3E8.

2E8 Enable onBoard Serial port 2 and address is 2E8.

Disabled Disable onBoard Serial port 2.

•

Serial Port 2 Irq

Disabled Disabled Serial Port1 Irq.

3 Set Serial Port1 Irq is 3. (Default Value)

4 Set Serial Port1 Irq is 4.

•

Parallel Port Address

378 Enable On Board LPT port and address is 378. (Default Value)

278 Enable On Board LPT port and address is 278.

3BC Enable On Board LPT port and address is 3BC.

Disabled Disable On Board LPT port.

•

Parallel Port IRQ

7 Set Parallel Port IRQ is 7. (Default Value)

5 Set Parallel Port IRQ is 5.

BIOS Setup

•

Parallel Port Mode

EPP Using Parallel port as Enhanced Parallel Port.

ECP Using Parallel port as Extended Capabilities Port. (Default Value)

Normal Normal Operation.

Bi-Directional Using Parallel port as Bi-Directional.

•

ECP Mode DMA Channel

3 Set Parallel Port DMA is 3. (Default Value)

0 Set Parallel Port DMA is 0.

1 Set Parallel Port DMA is 1.

2 Set Parallel Port DMA is 2.

Figure 2-3: Advanced

•

OnBoard Floppy Controller

Enabled Enabled OnBoard Floppy Controller. (Default Value)

Disabled Disabled OnBoard Floppy Controller.

BIOS SETUP UTILITY

Advanced

Floppy Configuration

OnBoard Floppy Controller [Enabled]

Floppy A [1.44 MB 3 ½”]

Floppy B [Disabled]

Diskette Write Protect [Disabled]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

6ETXDR Motherboard

•

Floppy Drive A / Floppy Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in

the computer.

Disabled No floppy drive installed

360KB, 5¼”. 5¼” PC-type standard drive; 360K byte capacity.

1.2MB, 5¼”. 5¼” AT- -type high density drive; 1.2M byte capacity (3½” when 3

Mode is Enabled).

720KB, 3½”. 3½” double-sided drive; 720K byte capacity

1.44MB, 3½”. 3½” double-sided drive; 1.44M byte capacity.

2.88MB, 3½”. 3½” double-sided drive; 2.88M byte capacity.

•

Diskette Write Protect

Enabled Diskette Write Protect.

Disabled Disabled Diskette Write Protect. (Default Value)

Figure 2-4: Advanced

BIOS SETUP UTILITY

Advanced

IDE Configuration

OnBoard PCI IDE Controller [Enable]

4Primary IDE Master [Not Detected]

4Primary IDE Slave [Not Detected]

4Secondary IDE Master [Not Detected]

4Secondary IDE Slave [Not Detected]

Hard Disk Write Protect [Disabled]

ß à Select Screen

á â Select Item

Enter Go To Sub Screen

F1 General Help

F10 Save and Exit

ESC Exit

BIOS Setup

Figure 2- -4 1: Advanced

•

OnBoard PCI IDE Controller

Disabled Disabled OnBoard PCI IDE Controller.

Enabled Enabled OnBoard PCI IDE Controller. (Default Value)

•

Type (Primary IDE Master, Slave / Secondary IDE Master, Slave)

Not Installed Not Installed Primary / Secondary IDE Master, Slave type.

Auto Auto detect Primary / Secondary IDE Master, Slave type.

CDROM Set type is CDROM.

ARMD Set type is ARMD.

LBA/Large Mode

Disabled Disabled LBA/Large Mode.

Auto Auto Set LBA/Large Mode.

Block (Multi-Sector Transfer)

Disabled Disabled Multi-Sector Transfer.

Auto Auto set block.

BIOS SETUP UTILITY

Advanced

Primary IDE Master (Primary IDE Slave,

Secondary IDE Master, Secondary IDE Slave)

Device: Not Detected

Type [Auto]

LBA/Large Mode [Auto]

Block(Multi-Sector Transfer) [Auto]

PIO Mode [Auto]

DMA Mode [Auto]

S.M.A.R.T. [Auto]

32 Bit Data Transfer [Enabled]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

6ETXDR Motherboard

PIO Mode

Auto Set PIO Mode to Auto.

0 Set PIO Mode to 0.

1 Set PIO Mode to 1.

2 Set PIO Mode to 2.

3 Set PIO Mode to 3.

4 Set PIO Mode to 4.

DMA Mode

Auto Set DMA Mode to Auto.

SWDMA 0~2 Set DMA Mode to SWDMA 0~2.

MWDMA 0~2 Set DMA Mode to MWDMA 0~2.

UDMA 0~4 Set DMA Mode to UDMA0~4.

S.M.A.R.T.

Disabled Enabled S.M.A.R.T. for Hard Disks.

Enabled Disabled S.M.A.R.T. for Hard Disks. (Default Value)

Auto Set Auto for S.M.A.R.T. for Hard Disks.

32 Bit Data Transfer

Enabled Enabled 32Bit Data Transfer. (Default Value)

Disabled Disabled 32Bit Data Transfer.

•

Hard Disk Write Protect

Disabled Disabled Hard Disk Write Protect. (Default Value)

Enabled Hard Disk Write Protect.

BIOS Setup

Figure 2-5: Advanced

•

Event Logging

Disabled Disabled Event Logging. (Default Value)

Enabled Enabled Event Logging.

•

Clear All Event Logs

Yes Enabled Clear All Event Logs. (Default Value)

No Disabled Clear All Event Logs.

BIOS SETUP UTILITY

Advanced

Event Log Configuration

Event Logging [Enabled]

Clear All Event Logs [No]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

6ETXDR Motherboard

Figure 2-6: Advanced

•

ACPI Shut Down Temp. (

C /

(This function will be effective only for the operating systems that support ACPI Function.)

Disabled Disabled ACPI Shutdown function. (Default Value)

60°C / 140°F Monitor CPU Temp. at 60°C / 140° ° °F, if Temp. > 60 C / 140 F

system will automatically power off.

70°C / 158°F Monitor CPU Temp. at 70°C / 158° ° °F, if Temp. > 70 C / 158 F

system will automatically power off.

80°C / 176°F Monitor CPU Temp. at 80°C / 176° ° °F, if Temp. > 80 C / 176 F

system will automatically power off.

90°C / 194°F Monitor CPU Temp. at 90°C / 194° ° °F, if Temp. > 90 C / 194 F

system will automatically power off.

BIOS SETUP UTILITY

Advanced

System Health Monitoring

ACPI Shut Down Temp. [Disabled]

CPU Temp. Alarm [Disabled]

CPU1 Fan Fail Alarm [No]

CPU2 Fan Fail Alarm [No]

Power Fan1 Fail Alarm [No]

Power Fan2 Fail Alarm [No]

System Fan Fail Alarm [No]

Reset Case Open Status [No]

Case Status [Closed]

CPU1 Present [OK!]

CPU2 Present [FAIL!]

Current CPU1 Temp. 53°C/127°F

Current CPU2 Temp. 127°C/260°F

Current CPU1 Fan Speed 5113 MPR

Current CPU2 Fan Speed 0 MPR

Current System Fan Speed 0 MPR

CPU VID 1.50V

Vcc2P 1.595V °F ß à Select Screen

Vcc2S 1.308V °F á â Select Item

Vcc 3 2.759V °F + - Change Field

Vcc 4.933V °F Tab Select Field

+12V 12.075V °F F1 General Help

5V SB 4.775V °F F10 Save and Exit

VBAT 2.408V °F ESC Exit

BIOS Setup

•

CPU Temp. Alarm

Disabled Normal Operation. (Default value)

60°C / 140°F Monitor CPU Warning Temp. at 60°C / 140°F

70°C / 158°F Monitor CPU Warning Temp. at 70°C / 158°F

80°C / 176°F Monitor CPU Warning Temp. at 80°C / 176°F

90°C / 194°F Monitor CPU Warning Temp. at 90°C / 194°F

•

Fan Fail Alarm

CPU 1/ CPU 2 / System / Power Fan 1 / Power Fan 2

No Fan Fail Alarm Function Disabled. (Default value)

Yes Fan Fail Alarm Function Enabled.

•

Reset Case Open Status

•

Case Status

If the case is closed, “Case Status” will show “Closed”.

If the case have been opened, “Case Status” will show “Closed”.

If you want to reset “Case Status” value, set “Reset Case Open Status”

to “Yes” and save CMOS, your computer will restart.

•

CPU 1 / CPU 2 Present.

Detect CPU1 / CPU 2 Status automatically.

•

Current CPU1 / CPU2 Temp. (

C /

Detect CPU 1 / CPU 2 / Temperature automatically.

•

Current CPU1 / CPU2 / System Fan Speed

Detect CPU 1 / CPU 2 / System Fan speed status automatically.

•

Current Voltage (V)

CPU VID (CPU2) / Vcc2P (CPU1) / Vcc2S (CPU2) / Vcc3/ Vcc / 5V SB / VBAT /

+12 V

Detect system’s voltage status automatically.

6ETXDR Motherboard

Figure 2-7: Advanced

•

Remote Access

Disabled Disable this Function. (Default Value)

Serial (ANSI) Server use COM port to control client.

BIOS SETUP UTILITY

Advanced

Configure Remote Access type and parameters

Remote Access [Disabled]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

BIOS Setup

Chipset

Figure 3: Chipset

•

Memory Scrubbing

Disabled Disabled Memory scrubbing. (Default Value)

Enabled Enabled Memory scrubbing writs the ECC corrected memory data back

to the DRAM.

•

ISA IO Cycle Delay (Define the delay inserted between an ISA I/O cycle and the

next cycle)

Full Delay Set ISA IO cycle delay is full delay.

1.5 BCLK Set ISA IO cycle delay is 1.5 BCLK.(Default Value)

2.5 BCLK Set ISA IO cycle delay is 2.5 BCLK.

3.5 BCLK Set ISA IO cycle delay is 3.5 BCLK.

•

MPS 1.4 Support (Support Multi Processor Specification revision 1.4)

Enabled Enabled MPS 1.4 support. (Default Value)

Disabled Disabled MPS 1.4 support.

BIOS SETUP UTILITY

Main Advanced Chipset PCIPnP Power Boot Security Exit

Memory Scrubbing [Disabled]

ISA IO Cycle Delay [1.5 BCLK]

MPS 1.4 Support [Enabled]

ß à Select Screen

á â Select Item

+ - Change Field

Tab Select Field

F1 General Help

F10 Save and Exit

ESC Exit

Produkt Specifikationer

Mærke:	Gigabyte
Kategori:	Bundkort
Model:	GA-6ETXDR
Bredde:	304.8 mm
Dybde:	243.84 mm
Ethernet LAN-porte (RJ-45):	2
Antal USB 2.0-porte:	2
Strømkilde type:	ATX
Maksimal intern hukommelse:	4 GB
Processorproducent:	Intel
Drivere inkluderet:	Ja
Netværksfunktioner:	Hurtigt ethernet
Antal PS/2-porte:	2
Processor sokkel:	Sokkel 370
Fejlkorrigerende kode:	Ja
Antal hukommelsesstik:	4
Motherboard form faktor:	ATX
Maksimal grafikadapterhukommelse:	8 MB
BIOS-type:	AMI
BIOS-hukommelsesstørrelse:	32 Mbit
Controller-grænsefladetype:	NS97317
Overclocking funktioner:	PCI 64-bit/33 MHz slots - 2
PCI-slots:	2
Antal COM-porte:	1
Grafik controller:	ATI Rage XL