Goodway GVC-18000 Manual
Goodway
Damprenser
GVC-18000
Læs gratis den danske manual til Goodway GVC-18000 (20 sider) i kategorien Damprenser. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Goodway GVC-18000, eller vil du spørge andre brugere om produktet?
Side 1/20
GVC-18000/
GVC-36000
Dry-Steam Cleaner
Operating and
Maintenance
Instructions
Read before operating.
GVC-18000/GVC-36000 0419
2
CONTENTS:
INTRODUCTION ....................................................................................................................................2
GENERAL ................................................................................................................................................3
IMPORTANT SAFETY INSTRUCTION ............................................................................................... 3-4
GROUNDING INSTRUCTIONS .............................................................................................................4
USE OF DETERGENTS ..........................................................................................................................5
GENERAL FEATURES ......................................................................................................................... 5-8
SET –UP....................................................................................................................................................8
OPERATION ............................................................................................................................................9
WATER REFILL: .....................................................................................................................................10
CONTINUOUS WATER REFILL ...........................................................................................................11
MAINTENANCE ...................................................................................................................................12
QUICK START GUIDE ..........................................................................................................................13
TECHNICAL INFORMATION ..............................................................................................................14
TROUBLESHOOTING ..........................................................................................................................15
STANDARD ACCESSORY LIST ............................................................................................................16
NON-STANDARD ACCESSORY LIST...........................................................................................................17-18
INSTRUCTIONS TO MOUNT THE VACUUM KIT ..............................................................................19
Thank you for purchasing this Goodway Dry-Steam Cleaner. We appreciate your
business and look forward to serving you in the future. As with all Goodway
products, you can be assured that the nest quality components and workmanship
have gone into this machine.
Please take a few minutes to read the following Operating and Maintenance
Instructions. Please pay particular attention to the safety instructions and exercise
caution when using this machine.
GOODWAY
®
TECHNOLOGIES CORPORATION
HVAC & FACILITY MAINTENANCE SOLUTIONS
For Sales Call: 1-800-333-7467
For Service Call: 1-800-370-2855
GVC-18000/GVC-36000 0419
3
GENERAL
The GVC-18000 and GVC-36000 Dry-Steam cleaners are the most powerful
dry-steam cleaner in their class. They melt away grease and grime, and can kill
bacteria and other microorganisms when high temperature is applied for extended
periods.Please review these instructions prior to installation and operation of this dry-
steam cleaner.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
To prevent operator injury and damage to the equipment, please read and observe
the following basic safety precautions:
1. Warning: Risk of severe injury – keep clear of nozzle – do not direct discharge
steam at persons – this product is to be used only by trained operators.
2. Read and understand all instructions before using.
3. Keep this manual with the unit at all times.
4. Do not operate without eye protection or other necessary protective gear. Consult
SDS for all chemicals and for CO² and OSHA exposure limits.
5. Warning: Hot accessories can lead to injuries, do not touch with bare skin.
6. Make sure that the water you ll into the water tank is clean. Avoid the use of
buckets or canisters to ll the tank unless these are completely free of dirt or
foreign objects.
7. Do not drag the machine by pulling the hose, this can damage the hose.
8. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
9. When using the optional vacuum accessory, do not use to pick up ammable or
combustible liquids such as gasoline, or use in areas where they may be present.
10. Check the power supply cable before use for any damage. In the event of damage
to the power supply cable, have it immediately replaced by the manufacturer or
qualied personnel.
11. Over length of power cord extension (longer than 82 ft or 25 m) may lead to
insufcient voltage supply and malfunction.
12. Warning: Inadequate extensions can be dangerous. Make sure that your extension
is correctly dimensioned and constructed according to national legislation.
13. Never immerse any part of the machine in water or other liquids.
GVC-18000/GVC-36000 0419
4
14. Check the steam hose and all accessories for damage before use and replace or
have them repaired immediately.
15. In the event of leakage of steam or liquid, switch off and disconnect power
immediately. Contact the manufacturer or service center.
16. Service must be performed by qualied persons.
17. Never use the machine in a tilted position, all 4 wheels must stand on a level surface.
18. Do not clean heat sensitive materials with steam, the heat of the steam could
cause damage.
19. Operate the machine only wearing appropriate PPE.
20. Ventilate work area when using toxic or pungent additives to reduce your exposure
to toxic fumes.
21. Be careful of slippery oors. Some additives make a normally safe area extremely
slippery and dangerous.
22. Keep operation area clear of all persons. Do not use unit with children or visitors in
the immediate area.
23. Do not change nozzle size. An incorrect nozzle could cause excessive pressure
resulting in equipment damage and possible personal injury.
24. Use only Goodway specied replacement parts and accessories.
25. Keep objects, loose clothing, hair, body parts away from openings and moving parts.
26. Do not operate unit when fatigued or under the inuence of drugs or alcohol.
27. Do not over reach or stand on unstable support. Keep good footing and balance at
all times.
28. Stay alert and watch what you’re doing.
29. Both front casters must be locked when unit is plugged into power supply.
GROUNDING INSTRUCTIONS
This dry-steam cleaner must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce the risk
of electric shock. This appliance is equipped with a cord having an equipment-
grounding conductor. The cord must be wired into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding conductor can result
in electric shock. Check with a qualied electrician or service person if you are in
doubt as to whether the outlet is properly grounded.
SAVE THESE INSTRUCTIONS
GVC-18000/GVC-36000 0419
5
14756 8
2
3
9
1. Power Disconnect Switch
2. Boiler Control Panel
3. Wet Steam/Detergent Panel
4. Emergency Kill Switch
5. Steam Output Selector - LOW/HIGH
6. Steam Regulator
7. Hose Connection Socket
8. Continuous Rell – Water Inlet Button
9. Water Tank Full LED
USE OF DETERGENTS
One of the principal advantages of steam is that it takes away the need to use
detergents. However, we recognize that in certain situations the addition of
detergent can assist the power of steam and speed up the cleaning process.
Goodway offers approved detergent (GVC-500) to be used via the detergent facility
for occasional use.
WARNING: other detergents should not be used as the chemical’s reaction to heat
is not always known. Heated chemicals can give off noxious fumes which can cause
serious injury.
WARNING: Do not put any chemical in the water tank. This will cause damage to
the boilers and pumps within the unit
Front Panel (Pic.1):
GENERAL FEATURES
GVC-18000/GVC-36000 0419
6
Boiler Control Panel (Pic.2):
2.7 2.5 2.4
2.6 2.8 2.3 2.2 2.1
2.1 Power On LED
2.2 Water Tank Low LED
2.3 Boiler Pump LED
2.4 Boiler Heating LED
2.5 Boiler On/Off Button
2.6 P1 Service Function
2.7 Temperature Display
2.8 P2 Service Function
Function of the P1 and P2 Buttons:
The buttons are used to read out the total hours run by the machine. To read total
hours, do as follows:
1. Press P2 (2.8) to visualize the hours run up to 999 – the display shows 3 digits
2. Press P1 (2.6) to visualize the hours up to 99000 – the display shows 2 digits
Now sum up both, for example if you press P2 and read 317 and then press P1 and
read 04 then you have a total of 4317 hours which the machine has run.
GVC-18000/GVC-36000 0419
7
Wet Steam/Detergent Panel (Pic.3)
Top Inlet Water Tank D.160mm (Pic.4)
3.1 Wet Steam Button (Blue)
3.2 +/- Level Buttons
3.3 Detergent Button
3.4 Level Indication LED
Pic. 4
GVC-18000/GVC-36000 0419
8
Hand-grip (Pic.5)
Hose-Grip Steam and Vacuum (Optional):
SET–UP
1. Remove from packaging and inspect unit. Report any discrepancies to
Goodway Technologies Corporation’s Customer Service at (800) 370-2855.
2. Attach handle to rear of unit using four included fasteners w/orange handles
3. Position this Dry-Steam cleaner in the area it will be used.
4. Connect the unit to the plant’s wiring. See unit’s nameplate for power
requirements. It is imperative that the ground connection is properly made.
See grounding instructions for more information.
5. Connect water supply hose to connector on rear of unit. Water supply pressure
must be between 1.5 psi and 100 psi.
6. Insert the Steam Hose into Connection Socket on front of machine (note - pull
back slightly on ring of hose connector to allow insertion into socket).
7. Connect output end of hose to accessory or nozzle for cleaning application.
11 Steam Handle
11.1 Steam Trigger
11.2 Detergent Button
11.3 Vacuum On/Off Button
11.4 White Lever
GVC-18000/GVC-36000 0419
9
WARNING: Always wear gloves, protective glasses and ear protection while
operating this machine.
Steam Only Function:
1. Turn the main switch 1 (Pic.1) to the ON position.
2. LED 2.1 (Pic.2) goes on to signal that the machine receives voltage
3. Remove the water tank cover 9.1 (Pic.4) and ll the tank 9 (Pic.4) with plain
tap water until the LED 9 (Pic.1) lights up, this is possible only if the machine
is turned on, or you see that the tank is full. Close the water tank. Also see
‘Continuous Water Rell’ section for optional continuous water relling.
4. Push the boiler ON button 2.5 (Pic.2) and the pump starts lling the boiler. LED
2.3 (Pic.2) lights up. Filling is automatically preformed when requested by the
water level sensor inside the boiler.
5. When the pump stops, LED 2.3 (Pic.2) goes out and the heating phase begins,
lasting approx. 5 minutes. During the heating phase LED 2.4 (Pic.2) will
continue to blink.
6. When LED 2.4 (Pic.2) stops blinking and stays on, the machine is ready for use.
(During use this light will often blink to show that the heating elements are on).
7. Insert the hose into the hose connection socket 7 (Pic.1), ensuring that it is
securely tted.
8. Fasten accessories to lances by rmly pushing them on to the tip (nozzle)
10.2 (Pic.5)
9. Pull the trigger 10 (Pic.5) on the hand-grip to start the steam output and direct
the steam jet towards the area to be cleaned.
10. Regulate steam output by turning the manual output regulator 6 +/- (Pic.1)
and/or by using selector 5 (Pic.1) for LOW or HIGH output. (Always select LOW
with the vacuum hose!).
NOTE: Before beginning steam cleaning operations, evacuate the condensation
left inside the steam hose into a bucket or other suitable place.
WARNING: In case of danger, injury of the operator, leakage of steam or anything
that makes it difcult to regularly turn the machine off, immediately hit the
emergency OFF button 3 (Pic.1). The switch will remain in the off position until
manually reset by turning the switch so that it pops back up! Reset ONLY after
having removed the cause of malfunction. See the troubleshooting section!
Wet Steam or Detergent:
To optimize the cleaning action of the steam, water from the internal tank 9 (Pic.4)
or detergent from one of the external canisters can be injected into the steam.
OPERATING INSTRUCTIONS
GVC-18000/GVC-36000 0419
10
1. Enable the wet steam feature by pressing the blue button 3.1 (Pic.3) and
then choose the level required with the +/- buttons 3.2 (Pic.3). Levels 1 & 2
are indicated for most jobs in which dry saturated steam is too dry, making
cleaning slower than necessary. Levels 3 & 4 allow for a strong rinsing action
of the steam but the steam temperature still stays above 120°C at the
lances tip.
2. Now enable switch 10.1 (Pic.5) on the top of the hand grip to activate the
injection of water into the steam while also pulling the steam trigger. The
water pump will run only while pulling the trigger.
3. To use the detergent feature press the yellow button 3.3 (Pic.3). First ll one
or both of the external canister on top of the machine with 5 liters of water
and detergent and make sure that the transparent hose is connected properly
to the chassis. You have 2 canisters available which you can ll as required for
a total of 10lt.
4. Choose the desired level of detergent required with +/- buttons 3.2 (Pic.3)
and if necessary do tests to nd the best level of detergent to inject.
5. Again enable switch 10.1 (Pic.5) on the top of the hand-grip to activate the
injection of detergent into the steam while also pulling the steam trigger. The
detergent pump will run only while pulling the trigger.
6. Priming the detergent pump: if the detergent canister runs empty the pump
may take a while to suck up the detergent and purge the air in the hose.
Observe the transparent hoses on the canister for visual feedback.
ATTENTION! Please use water with low levels of mineralization that has been
ltered or softened in order to avoid mineral deposits which can obstruct the
free ow of steam within the hose. For a correct use of the machine, do not use
demineralized or distilled water with a value lower than 96 TDS or 200 μs/cm. Also,
remnants of detergent in the transparent hose or pump can cause blockage and or
damage the pump, please ush the detergent circuit when not used regularly.
WARNING:This Machine has been designed for use with non- foaming and non-
corrosive detergent. Use of foaming and/or corrosive detergent will damage the
machine! You are advised to use only the detergent specied by the manufacturer.
Use of any other detergent may void warranty.
WATER REFILL:
When the water in the tank nishes, the machine emits an acoustic signal and LED
2.2 (Pic.2), signaling “water tank low” lights up along with 9 (Pic.1). After a little
more time the steam outlet is blocked until the tank is relled.
Perform the following operations:
1. Press button 2.5 (Pic.2) to turn off the boiler.
2. Open the plug 9.1 (Pic.5) and rell the tank with clean tap water. Close tank.
3. Press button 2.5 (Pic.2) and the pump will start lling up the boiler, LED 2.3
(Pic.2) and 2.4 (Pic.2) blink.
4. Since the boiler is already under pressure, LED 2.4 (Pic.2) light up steady after a
few seconds and the machine is ready to resume work.
GVC-18000/GVC-36000 0419
11
CONTINUOUS WATER REFILL
The internal water tank can be relled
with water automatically and continuously.
Connect the machine to a water hose
by using the supplied ¾” garden hose
connector. Fasten the male part to the water
inlet at the rear of the machine, fasten the
female to the hose and then connect both.
1. Open the water from the tap.
2. Push the button 8 (Pic.1).
3. The tank will now ll itself. Sensors ensure
the correct water level.
ATTENTION: pressure of water supply for
the continuous rell must not be greater than
145 PSI (10 Bar) or less than 14.5 PSI (1 Bar).
WARNING: Never push the button 8 if the
machine is not connected to the water hose.
This would cause water to ow out of the tank
and onto the oor. When done working, push
the button 8 (Pic.1) OFF and disconnect the
water hose. After Use:
NOTE: Output Power Selection Switch 5
(Pic.1) must be on 72kW to properly relieve pressure.
• Turn off the boilers 2.5 (Pic.2).
• Release steam from the boilers by squeezing the trigger. Do this until the
pressure in the unit reaches 6 bar.
• Turn off the main power 1 (Pic.1). Now wait 30 seconds.
• Turn the machine back on 1 (Pic.1). Turn the boilers back on 2.5 (Pic.2). Wait for
the pump to stop.
• Turn off the boilers 2.5 (Pic.2) as soon as the pump stops. Release steam until
the unit reaches 6 bar again. Turn off the main power 1 (Pic 1).
• Dry all accessories and store them in a dry environment.
• Clean the machine with a cloth, warm water and if necessary use a
neutral detergent.
GVC-18000/GVC-36000 0419
12
ATTENTION: Maintenance should be done every 6 to 12 months or more often if
used very heavily and/or if the water is very hard. Make arrangements with your
dealer or distributor for professional maintenance and assistance. Only trained
persons are allowed to perform the below procedure!
The amount of carbonates in the water (chalk, salts and other minerals) determine
the hardness of the water you use with this machine. When water is heated up
these carbonates will “fall out”, that is they will become small particles that in the
worst case can encrust your boiler, the heating element and other components.
Please clean your boiler as described below regularly, more so if you have hard
water from the tap. Do not use completely demineralized or distilled water with
your machine because such water contains no minerals and carbonates and could
lead to malfunction!
DANGER: Wear protective clothing, gloves and glasses while operating the below
procedure, the hot water can cause injuries!
DANGER: Remove electrical power before servicing.
CLEANING THE BOILER:
• Perform this task at least every month, but ideally at the end of each
working week!
• Never bleed the boiler as long as any pressure is still inside the boiler!!!
• Make sure the water inside the boiler is not hot.
• Gently rock the machine to agitate carbonate deposits in the boiler.
• Open the drain valve over a gully/drain or a container with a suitable capacity
to catch the water from the boiler.
• Empty the content of the boiler while gently shaking the machine.
• Close the drain valve
Boiler Descaling: Chemical scale removal may be necessary depending on use
and water quality, contact Goodway Technologies for recommendations.
Inspect and replace the water lter as necessary:
MAINTENANCE
GVC-18000/GVC-36000 0419
13
QUICK START GUIDE:
TURNING OFF THE MACHINE
GVC-18000 Quick Start Guide
Shut down the boilers
and release the steam
until the unit reaches
about 6 bar.
1
Inspect the machine
and accessories
for damage.
1
Fill the water tank
with clean water
(NO chemicals).
Check for leaks.
2
Shut the machine off
and wait 30 seconds.
2
Connect
the steam hose
to machine, and
connect the spray
wand to the
steam hose.
4
Turn on the Main Power
switch, and then
turn on the Boiler
On button. The LED
light will start
blinking.
5
Once the machine starts to
heat up, release air pressure
by pulling the trigger on
the spray gun until air
stops coming out of the
nozzle. Do this for a few
seconds.
6
Plug the machine
into a three phase
power receptacle.
3
Turn the machine back on and turn on the boilers
and wait until the pumps stop.
3
Now turn off the boilers and release steam until
the unit reaches 5 bar and shut down the
machine again.
4
STARTING THE MACHINE
420 West Avenue
Stamford, CT 06902-6384 U.S.A.
Allow the machine to build
up to operating tempera-
ture (350˚F) and pressure
(10 bar), and then use as
recommended.
9
Once the pressure gauge
reads 10 bar, pull the trigger
on the spray gun until all
the water is purged from
the line.
8
10 bar
The LED light will continue
to blink until the pressure
gauge reads 10 bar, it
will take the machine up
to 5 minutes to heat up.
7
LED
®
Call Us With Your Dirt: 1-800-333-7467
L-325 0818
GVC-18000/GVC-36000 0419
14
TECHNICAL INFORMATION
Specication GVC-18000 GVC-36000
Input Power:
22 amps, 480 V, 60 Hz AC, three
phase (Maximum 18,000 W)
53 amps, 480 V, 60 Hz AC, three
phase (Maximum 36,000 W)
Power Supply Cord:
33', 10-4 33', 6-4
Output Steam
Pressure:
Adjustable, 0-145 PSI Adjustable, 0-145 PSI
Output Steam
Temperature:
290°F 290°F
Max Steam Output:
7 GAL/HR (dry)
9.5 GAL/HR (wet)
13.5 GAL/HR (dry)
17.5 GAL/HR (wet)
Dry Steam Regulation:
Manual 0-max Manual 0-max
Wet Steam Regulation:
4 electronically
regulated levels
4 electronically
regulated levels
Detergent Function:
4 electronically
regulated levels
4 electronically
regulated levels
Boilers:
Two 2.4 gallons
stainless steel
Four 2.4 gallons
stainless steel
Heat Up Time:
5 min 5 min
Water Tank:
10.6 gallons stainless steel 10.6 gallons stainless steel
Chemical Tank:
Two 1.3 gallons Two 1.3 gallons
Dimensions:
44" high x 28" wide x 41"
deep
44" high x 28" wide x 41"
deep
Weight:
194 lbs net dry 225 lbs net dry
Optional Vacuum
Power:
1200 Watt 1200 Watt
Vacuum Container
Volume:
5.28 gallons 5.28 gallons
Continuous
Feeding Inlet:
YES - ¾" Female Garden
Hose Connector
YES - ¾" Female Garden
Hose Connector
GVC-18000/GVC-36000 0419
15
Problem Solution
All LED’s and the display of the
front panel start blinking and the
display shows letters or numbers
The voltage is insufcient to run
the machine
Steam leaks from accessories or it
is hard to disconnect them
Replace the gaskets, clean and
place a light lm of silicone grease on
the gasket
Hose plug hard to insert in the
machine socket
Lubricate the steam socket
connection with some silicone
No steam output but the machine is
pressurized.
Make sure the manual output valve is
open
Machine heating time too long
Remove scale from boiler as
described in the maintenance section
The pressure drops rapidly during
operation
Remove scale from boiler as
described in the maintenance section
The pressure rises rapidly and the
pump continues to ll the boiler
The machine needs to be serviced
Problem Solution
Vacuum does not turn on when
enabled on the hose-grip
Check the vacuum is plugged in right and
the vacuum is on.
The vacuum does not effectively
suck up dirt
Clean or replace the lter, and
check the housing for blockage
Leakage of steam or water into
the machine
Push the emergency off button 4
and unplug the machine. Contact your
service partner for instructions.
TROUBLESHOOTING
TROUBLESHOOTING THE OPTIONAL VACUUM
If the below solutions do not resolve your problem please contact your dealer
or distributor.
GVC-18000/GVC-36000 0419
16
STANDARD ACCESSORY LIST
Specication GVC-18000 GVC-36000
9385(GVC-18000)
9386 (GVC-36000)
Quick-release pistol
grip + 33' hose
KIT0914/AR/3.5
(GVC-18000)
KIT0914/AR/5.5
(GVC-36000)
SHORT DETAIL
LANCE
KIT0915/AR/3.5
(GVC-18000)
KIT0915/AR/5.5
(GVC-36000)
ONE-PIECE 40"
WAND WITH DETAIL
LANCE
KIT0916/AR/3.5
(GVC-18000)
KIT0916/AR/5.5
(GVC-36000)
ONE-PIECE 20"
WAND WITH DETAIL
LANCE
93-KIT0814/I
4X 2¼" CIRCULAR
STAINLESS STEEL
BRUSHES
93-KIT0814/N
4X 2¼" CIRCULAR
NYLON BRUSHES
93-KIT0814/O
4X 2¼" CIRCULAR
BRASS BRUSHES
93-KIT0815/I
4X 1½" CIRCULAR
STAINLESS STEEL
BRUSHES
93-KIT0815/N
4X 1½" CIRCULAR
NYLON BRUSHES
93-KIT0815/O
4X 1½" CIRCULAR
BRASS BRUSHES
GVC-18000/GVC-36000 0419
17
93-KIT0816/I
4X 1” CIRCULAR
STAINLESS BRISTLES
93-KIT0816/N
4X 1” CIRCULAR
NYLON BRISTLES
93-KIT0816/O
4X 1” CIRCULAR
BRASS BRISTLES
93-KIT0020
SAFETY GLOVES
93-KIT0021
SAFETY
GOGGLES
NON-STANDARD ACCESSORY LIST
Part# Description Picture
9319-VAC-KIT
VACUUM KIT 1200W
FOR INDUSTRIAL
3PHASEMACHIN ES KIT
INCLUDES:
- VACUUM
WITH SUPPORT
- STEAM & VACUUM
HOSE 4 METER
- ACCESSORY SET
9387
1 STEAM/VAC
HOSE 4 METER
v93-KIT0801
2 EXTENSION
TUBES L.500
93-KIT0802
1 EXTENSION
TUBE L.250
GVC-18000/GVC-36000 0419
18
Part# Description Picture
93-KIT0803
1 FLOOR BRUSH
L.500
93-KIT0823
1 TEFLON INSERT
FLOOR BRUSH L.500
93-KIT0825
1 RUBBER INSERT
FLOOR BRUSH L.500
93-KIT0804
1 FLOOR BRUSH L.300
93-KIT0822
1 TEFLON INSERT
FLOOR BRUSH L.300
93-KIT0824
1 RUBBER INSERT
FLOOR BRUSH L.500
93-KIT0805
1 SQUEEGEE L.300
93-KIT0808/DA/2.5
1 STEAM-VAC
LANCE 2.5MM
93-KIT0808/DA/350/2.5
1 STEAM-VAC
LANCE L. 350 2.5MM
93-KIT0810
1 ANGLED TUBE 45°
NON-STANDARD ACCESSORY LIST
GVC-18000/GVC-36000 0419
19
1. Fit both ends of the vacuum support into the holes between the back wheels
and x it with the two supplied screws.
2. Put the vacuum cleaner on the support.
3. Connect the vacuum cleaner to the vacuum socket behind the cleaner using
the special short vacuum hose.
4. Plug the vacuum into the receptacle on the rear, near the vacuum socket.
5. Enable the main ON/OFF switch located on the vacuum head.
6. Connect the steam and vacuum hose to the steam socket.
7. Start the steam machine as explained.
8. Determine the required steam output by regulating manually with valve 6 (Pic.1).
9. Press the trigger 11 (Pic.6) on the hose grip to enable steam output.
INSTRUCTIONS TO MOUNT THE VACUUM KIT:
Provides innovative maintenance solutions for a wide variety
of industries including commercial HVAC, food and beverage
processing, power generation and manufacturing.
HVAC & FACILITY MAINTENANCE SOLUTIONS
For Sales Call: 1-800-333-7467
For Service Call: 1-800-370-2855
GOODWAY
®
TECHNOLOGIES CORPORATION
420 West Avenue, Stamford, CT 06902 USA
Tel: 203-359-4708 · Toll-Free Tel: 800-243-7932
Fax: 203-359-9601 · Toll-Free Fax: 800-359-9625
Email: goodway@goodway.com
Visit: www.goodway.com
P/N MNL-GVC-18KW-36KW
©Copyright 2019 Goodway Technologies Corp., Stamford, CT USA
Effective date April 3, 2019
Goodway is a Trademark of Crossford International.
Goodway reserves the right to improve products; contact the factory for the latest conguration and uses.
Produkt Specifikationer
| Mærke: | Goodway |
| Kategori: | Damprenser |
| Model: | GVC-18000 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Goodway GVC-18000 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Damprenser Goodway Manualer
21 August 2024
Damprenser Manualer
- Laurastar
- Sauber
- Imetec
- Scarlett
- Quigg
- SALAV
- Thane
- Tineco
- Wagner SprayTech
- Beper
- Bestron
- Lavorwash
- Leifheit
- Orava
- Continental Edison
Nyeste Damprenser Manualer
13 Juni 2025
11 Juni 2025
11 Juni 2025
9 Juni 2025
8 Juni 2025
7 Juni 2025
4 Juni 2025
1 Juni 2025
10 April 2025
28 Marts 2025