Grundig GD-CT-BC2116T Manual

Grundig Overvågningskamera GD-CT-BC2116T

Læs gratis den danske manual til Grundig GD-CT-BC2116T (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 80 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 40.5 anmeldelser. Har du et spørgsmål om Grundig GD-CT-BC2116T, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specication for
camera parameters and functions.
Introduction
Please read these instructions carefully and keep them
for future reference. You must heed all the warnings
and cautions as well as follow all the safety and instal-
lation instructions.
Safety Instructions
Make sure that you only use the power adapter that is
specied in the specications sheet of the product. If
you use any other adapter or connect the power supply
incorrectly, this may cause explosion, re, electric
shocks or damage the product.
1 INTRODUCTION
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology. It features high resolution,
low image distortion and low noise, etc. , which
makes it suitable for surveillance system and
image processing system.
• High performance CMOS sensor and high
resolution bring high-quality image;
• Low illumination;
• OSD menu, parameters are congurable;
• Support auto white balance, auto gain control,
• Support image effect adjustment;
• Unit transmission control;
• Advanced 3 - axis design meets different
installation requirements.
1.2 Overview
1.2.1 Overview of Type I Camera
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type II Camera
Figure 1-2 Overview of Type II Camera
1.2.3 Overview of Type III Camera
Figure 1-3 Overview of Type III Camera
Abetechs GmbH 20171127 www.Grundig-Security.com
GD-CT-AC2116T
TVI Bullet Camera
User Guide
GRUNDIG-SECURITY.COM
2 INSTALLATION
Before you start:
• Please make sure that the device in the package
is in good condition and all the assembly parts are
included.
• Make sure that all the related equipment is pow-
er-off during the installation.
• Check the specication of the products for the
installation environment.
• Check whether the power supply is matched with
your power output to avoid damage.
• Please make sure the wall is strong enough to
withstand three times the weight of the camera and
the mounting.
• If the wall is made of cement, you need to insert
expansion screws before you install the camera.
If it is a wooden wall, you can use self-tapping
screw to secure the camera.
• If the product does not function properly, please
contact your dealer or the nearest
service center. Do not disassemble the camera for
repair or maintenance by yourself.
2.1 Installation of Type I Camera
Steps:
1. Drill the screw holes according to the drill
template.
2. Screw the clip plate onto the mounting base
loosely.
Figure 2-1 Drill Template
3. Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4. Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
Do not connect several devices to one power adapter
as this may cause an adapter overload and can lead to
over-heating and re. Make sure that the plug of the
power adapter is rmly connected to the power socket.
Do not use any accessories that are not recommended
by GRUNDIG. Do not modify the product in any way.
If the product starts to smell or smoke comes out of
the device, immediately stop using the product and
disconnect it from the power supply to prevent re
or electric shocks. Then contact your dealer or the
nearest service center.
If the product does not work correctly, contact your
dealer or nearest service center. Never open, disas-
semble or alter the product yourself. GRUNDIG cannot
accept any liability or responsibility for problems
caused by attempted and unauthorized repair and
maintenance.
Do not aim the camera or camera lens at a strong light
such as the sun or a bright lamp. Irreversible damage
to the camera can be caused by a strong light.
Do not expose the sensor of the product to laser beams
as this may damage the sensor.
Do not install the product near radiation sources.
Do not install the product near heat sources, like radi-
ators or other equipment that produces some heat.
Installation References
Do not install the product on surfaces or in places that
are vibrating. This product is not dedicated to be used
in vehicles, trains etc..
Do not touch the sensor module with your ngers.
Always adjust the focus by using a grey lter or at low
illumination.
If the product supports IR, you need to take some
precautions to prevent IR reection. Do not install the
product close to reective surfaces of objects as this
may cause reection. The foam ring around the lens
must be seated ush against the inner surface of the
bubble to isolate the lens from the IR LEDS.

Produkt Specifikationer

Mærke: Grundig
Kategori: Overvågningskamera
Model: GD-CT-BC2116T

Har du brug for hjælp?

Hvis du har brug for hjælp til Grundig GD-CT-BC2116T stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Grundig Manualer

Grundig

Grundig GD-CT-BC2116T Manual

31 Juli 2024
Grundig

Grundig GCI-C0735P Manual

7 November 2023
Grundig

Grundig GCI-K0503B Manual

6 Marts 2023

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

AVer

AVer HUB35-EXT35 Manual

11 December 2025
4XEM

4XEM SD8111 Manual

11 December 2025
4XEM

4XEM VIVOTEK Manual

11 December 2025
4XEM

4XEM MD7560 Manual

10 December 2025
AVer

AVer MT100 Manual

10 December 2025
4XEM

4XEM 4X-FD7132 Manual

10 December 2025
Telycam

Telycam Vision+ N3 Manual

7 December 2025
FLIR

FLIR FC-690 AI Manual

5 December 2025
FLIR

FLIR FH-625 R Manual

5 December 2025
FLIR

FLIR FC-644 AI-R Manual

5 December 2025