Hakko FX-888D Manual

Hakko Loddemaskine FX-888D

Læs gratis den danske manual til Hakko FX-888D (15 sider) i kategorien Loddemaskine. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Hakko FX-888D, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/15
Cleaning wireHAKKO FX-888D Station
HAKKO FX-8801 Soldering iron
Iron holder (with cleaning sponge)
Instruction Manual
1
1
1
1
1
Instruction Manual
1. PACKING LIST AND PART NAMES
Please check to make sure that all items listed
below are included in the package.
*HAKKO FX-8802 / FX-8803 / FX-8804 (not included) can be connected to HAKKO FX-888D station.
*When using the HAKKO FX-8802/FX-8803/FX-8804, please use it with the applicable iron holder.
HAKKO FX-8801
Cord assembly
Iron holder
Cleaning sponge
Iron holder
base
HAKKO FX-888D Station
Power switch
OFFON
Cleaning wire
Receptacle
Thank you for purchasing the HAKKO FX-888D soldering station.
Please read this manual before operating the HAKKO FX-888D.
Keep this manual readily accessible for reference.
Iron receptacle
This product includes such features as electrically conductive plastic parts and grounding of the unit
as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe
the following instructions:
1. The plastic parts are not insulators, they are conductors. When making repairs or replacing
parts, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
■ Electrostatic Protection
AC26V 65W
< 2 Ω
< 2 mV
Ceramic heater
3.9 ft. (1.2m)
8.5 in. (217mm) with 1.6D tip
0.10 lb. (46g / 1.62 oz.) with 1.6D tip
Power consumption 70W
● Station
* The temperature was measured using the FG-100 thermometer. * This product is protected against electrostatic discharge.
* Specifications and design are subject to charge without notice.
● HAKKO FX-8801 Soldering iron
Power consumption
Tip to ground resistance
Tip to ground potential
Heating element
Cord
Total length (w/o cord)
Weight (w/o cord)
2. SPECIFICATIONS
Output
Temperature range
Temperature stability
Dimensions (W × H × D)
Weight (w/o cord)
AC26V
120 - 899℉ (50 - 480℃)
±1.8℉ (±1℃) at idle temperature
{When set to 400-899℉ (200-480℃)}
3.9(W) × 4.7(H) × 4.7(D) in.
(100 × 120 × 120 mm)
2.6 lb. (1.2kg)
A. Setup the iron holder
1. Fit the small sponge pieces into the hollows of the iron holder base.
2. Add an appropriate amount of water into the iron
holder base. The small sponge will absorb water
and help keep the large sponge damp at all times.
3. Dampen the large sponge and place it on the
iron holder base.
*When using a Cleaning Wire
Place it in the iron holder as shown on the right. See
"2.Using a Cleaning Wire" in section "7. MAINTENANCE"
4.INITIAL SETUP
Small sponge
pieces
Large sponge
Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s
attention to significant items. They are defined as follows:
WARNING
When power is ON, tip temperatures will be between 120 to 899℉. (50 and 480℃) To avoid injury or
damage to personnel and items in the work area, observe the following:
● Do not touch the tip or the metal parts near the tip.
● Do not allow the tip to come close to, or touch, flammable materials.
● Inform others in the area that the unit is hot and should not be touched.
● Turn the power off when not in use, or left unattended.
● Turn the power off when changing parts or storing the HAKKO FX-888D.
● This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in safe way and understand the hazards
involved.
● Children shall not play with the appliance.
● Cleaning and user maintenance shall not be made by children without
supervision.
● The unit is for a counter or workbench use only.
● If the power cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid personal injury
or damage to the unit.
● The unit is for a counter or workbench use only.
Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved.
Failure to comply with a WARNING may result in serious injury or death.WARNING:
CAUTION :
CAUTION
3. WARNINGS, CAUTIONS AND NOTES
To prevent accidents or damage to the HAKKO FX-888D, be sure to observe the following:
● Do not use the HAKKO FX-888D for applications other than soldering.
● Do not strike the iron against hard objects to remove excess solder. This will damage the iron.
● Do not modify the HAKKO FX-888D.
● Use only genuine Hakko replacement parts.
● Do not allow the HAKKO FX-888D to become wet, or use it with wet hands.
● Remove power and iron cords by holding the plug. not the wires.
● Be sure the work area is well ventilated. Soldering produces smoke.
● While using the HAKKO FX-888D, don’t do anything which may cause bodily harm or physical damage.
CAUTION
Be sure the sponge is moistened with water
before use to avoid damaging the tip.

Produkt Specifikationer

Mærke: Hakko
Kategori: Loddemaskine
Model: FX-888D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hakko FX-888D stil et spørgsmål nedenfor, og andre brugere vil svare dig


Loddemaskine Hakko Manualer

Hakko

Hakko FX-888D Manual

31 August 2024

Loddemaskine Manualer

Nyeste Loddemaskine Manualer

Toolcraft

Toolcraft LWK-100 Manual

2 Oktober 2025
Toolcraft

Toolcraft AT-300 Manual

1 Oktober 2025
Toolcraft

Toolcraft ZD-10MB Manual

1 Oktober 2025
NEO Tools

NEO Tools 19-158 Manual

30 September 2025
Telwin

Telwin Force 125 954194 Manual

28 September 2025
Yato

Yato YT-8273 Manual

27 September 2025
Telwin

Telwin Infinity 150 954194 Manual

27 September 2025
Telwin

Telwin Force 170 954422 Manual

27 September 2025
Telwin

Telwin Infinity 220 954194 Manual

27 September 2025
Telwin

Telwin Infinity 225 954556 Manual

27 September 2025