Henry Engineering Micromixer Manual

Henry Engineering Stavblender Micromixer

Læs gratis den danske manual til Henry Engineering Micromixer (2 sider) i kategorien Stavblender. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Henry Engineering Micromixer, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
MICROMIXER
FOUR INPUT STEREO MIXER
HENRY ENGINEERING
503 Key Vista Drive
Sierra Madre, CA 91024
tel: 626.355.3656
fax: 626.355.0077
website: www.henryeng.com
DESCRIPTION
MICROMIXER is a four-input, two-output stereo mixer/combiner for utility use. The unit has
balanced bridging inputs for four audio sources (two stereo pairs) which can be mixed to two
outputs (one stereo pair). A level control is provided for each input. Selectable 'assign'
switching permits any input to be fed to either or both outputs. DC coupled circuitry provides
excellent sonic performance.
INSTALLATION
All connections to the MicroMixer are made via plug-in connectors. Remove about 1/8” of
insulaton, insert wires into the plug, and tighten the screws. Be sure that no bare wires are
exposed.
Audio inputs to the MicroMixer should be connected to the balanced input terminals labeled 1, 2,
3, and 4. For unbalanced inputs, install a jumper between the (-) terminal and G (ground). All
inputs are bridging; it is not necessary to terminate the source unless required by the source
equipment.
Audio outputs from the MicroMixer are connected to the two outputs labeled L (Left) and
R (Right). The output circuitry will drive any load of 600 ohms or higher. It is not necessary to
terminate the outputs. For unbalanced outputs, connect to the (+) and G terminals only. DO
NOT short the (-) terminal to ground.
OPERATION
The input levels to the MicroMixer should be between -10 and +8 dBm. Adjust each input
channel using the INPUT LEVEL controls. Unity gain is achieved with these controls set to 10
o'clock; with nominal input levels of +4 dBm the Input Level controls should be run near this
setting. It is recommended that input levels be initially set with a level indicator (VU meter,
scope, VOM) temporarily connected to the MicroMixer's output to monitor output levels. The
average output level should not exceed +8 dBm to ensure adequate headroom.
Each output channel (L & R) has four ASSIGN switches that determine which of the four input
signals are fed to that output. Select the input sources desired by switching the appropriate
channels ON (down). For example, if inputs 1 and 3 should be fed to the LEFT output, set Left
output assign switches 1 and 3 ON, with 2 and 4 OFF.
SPECIFICATIONS
INPUTS -10 to +8 dBm; balanced 20K or unbalanced 10K
GAIN 10 dB maximum
OUTPUTS +4 dBm nominal, +26 dBm max; 600 ohms or higher, 4X
FREQ RESP DC to 20 kHz, +/- 0.25 Db
NOISE 80 dB below +4 dBm output
DISTORTION .008% IM/THD
543
D
C
B
A
LEFT
+
-
2
INPUTS
15V
+
RIGHT
+
GND
GND
-
LEFT
-
RIGHT
4
1
INPUTS
SEC
-
230V
PRI
+
AC
GND
BLK
GND
3
-15V
+15V
-15V
+15V
-15V
+15V
-15V
+15V
+15V
RP1F 4.7K DIP
6 11
+
-
U2B
NE5532
5
6
7
8 4
C15
.1uF
+
C12
330uF 25V
RP2A
4.7K DIP
116
RP1G 4.7K DIP
7 10
+
-
3
2
8 4
J2
1
2
3
4
5
6
RP3H 4.7K DIP
89
RP2E 4.7K DIP
512
R38
5K POT
1 3
2
E1
RP3A 4.7K DIP
116
+
-
U2A
NE5532
3
2
1
8 4
C6
.001uF
R36
5K POT
1 3
2
RP1C 4.7K DIP
3 14
TP2
1
C5
.001uF
+
-
3
2
8 4
RP2F
4.7K DIP
611
C8
.001uF
C2
.001uF
RP3G 4.7K DIP
710
RP2G 4.7K DIP
710
C17
.1uF
RP3B 4.7K DIP
215
C7
.001uF LED1
LED
J1
1
2
3
4
5
6
RP1B 4.7K DIP
2 15
C1
.001uF
TP1
RP1H 4.7K DIP
8 9
RP2B 4.7K DIP
215
C4
.001uF
RP3E 4.7K DIP
512
RP1E 4.7K DIP
5 12
RP1A 4.7K DIP
1 16
RP2H
4.7K DIP
89
C13
.1uF
+
-
U1B
NE5532
5
6
7
8 4
R35
5K POT
1 3
2
SW2
SW DIP-4
1
2
3
4
8
7
6
5
C19
.1uF
RP3D 4.7K DIP
413
+
-
5
6
8 4
R37
5K POT
1 3
2
D2
1N4004
SW1
SW DIP-4
1
2
3
4
8
7
6
5
RP2C 4.7K DIP
314
E6F1
115V: 250 ma; 230V: 125ma
RP3F 4.7K DIP
611
RP2D
4.7K DIP
413
1
3
2
5
6
7
RP3C 4.7K DIP
314
D4
1N4004
R39
3.9K, 5%
+
-
U1A
NE5532
3
2
1
8 4
C3
.001uF
Q1 LM7815
3
2
1
IN
GND
OUT
RP1D 4.7K DIP
4 13
D1
1N4004
E7
+
-
5
6
8 4

Produkt Specifikationer

Mærke: Henry Engineering
Kategori: Stavblender
Model: Micromixer

Har du brug for hjælp?

Hvis du har brug for hjælp til Henry Engineering Micromixer stil et spørgsmål nedenfor, og andre brugere vil svare dig


Stavblender Henry Engineering Manualer

Henry Engineering

Henry Engineering Micromixer Manual

11 September 2024

Stavblender Manualer

Nyeste Stavblender Manualer

Graef

Graef HB 802 Manual

31 Juli 2025
Denon DJ

Denon DJ DN-X100 Manual

30 Juli 2025
Denon DJ

Denon DJ DN-X300 Manual

30 Juli 2025
Denon DJ

Denon DJ DN-X1500S Manual

30 Juli 2025
Denon DJ

Denon DJ DN-X500 Manual

30 Juli 2025
Denon DJ

Denon DJ DN-X050 Manual

29 Juli 2025
Denon DJ

Denon DJ SMX-2000 Manual

29 Juli 2025
Denon DJ

Denon DJ DN-X1500 Manual

29 Juli 2025
Denon DJ

Denon DJ DN-X800 Manual

29 Juli 2025
Denon DJ

Denon DJ DN-X900 Manual

29 Juli 2025