Hestan Aspire 20 Manual

Hestan Ikke kategoriseret Aspire 20

Læs gratis den danske manual til Hestan Aspire 20 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Hestan Aspire 20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

OUTDOOR CABINETS

Installation Instructions

AETRC / AETC

CABINET INSTALLATION (AETRC)

IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN

INSTALLER SHOULD LEAVE THESE INSTRUCTIONS WITH THE HOMEOWNER

1. Your new Aspire cabinets come with doors and drawers pre-installed in their frames. It will be necessary

to detach them before installing the frame in your island structure. To remove the drawer(s) from the

frame, press the release lever (see below) on each side of the drawer to disengage the slide (up on the left,

down on the right), then pull the drawer all the way out.

Some parts have sharp edges. Care must be taken when handling the various components to avoid personal

injury. Wear gloves when handling.

TOOLS REQUIRED:

Work gloves

Safety glasses

Electric drill with assorted bits for mounting hardware, masonry anchors, etc. where needed

Phillips screwdriver

Flat-blade screwdriver

Level

Tape measure

Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper and

initiate a damage claim. Hestan Commercial Corp. is not responsible for shipping damage. DO NOT discard

any packing material (box, pallet, straps) until the unit has been inspected.

Remove all exterior packaging materials, banding, tape, etc. Remove all protective film from the inside of your

cabinets. You may leave any exterior protective film on until after installation is complete.

RELEASE

LEVER

FRAME

CABINET INSTALLATION

(continued)

2. Consult the table at the end of this instruction manual to determine the appropriate cutout dimensions

for the Aspire Outdoor cabinet product you are installing. The cutouts should be square at all corners

for proper fitment of the cabinet. The installer will have to build up any internal structural elements or

supports in the island in order to secure the cabinet in place. Stainless steel hardware (not included) is

highly recommended.

3. Slide the frame into the opening and check for proper alignment. Secure the frame to the structural

members of your island using the various available mounting holes in the frame, and inside the cabinet

itself. Use at least 2 screws per side.

4. Reinstall the drawer(s) by aligning the slides on either side and pushing the drawer back into the opening.

You will hear the release levers click. Open and close the drawer a few times to check for proper function

and alignment. There are adjustment screws on either side of the drawer should vertical adjustment be

needed.

Produkt Specifikationer

Mærke:	Hestan
Kategori:	Ikke kategoriseret
Model:	Aspire 20

Har du brug for hjælp?

Hvis du har brug for hjælp til Hestan Aspire 20 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hestan Manualer

Hestan GFDSL241 Manual

30 August 2024

Hestan GRWSR24 Manual

30 August 2024

Hestan GFDSL242 Manual

30 August 2024

30 August 2024

30 August 2024

30 August 2024

30 August 2024

Hestan GRWGL24 Manual

30 August 2024

Hestan Aspire 20 Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Icom MB-91 Manual

19 Juni 2025

Metra 98-7599 Manual

19 Juni 2025

Parkside HG00490D Manual

19 Juni 2025

JUNG 104.15 Manual

19 Juni 2025

Rane SP 13 Manual

19 Juni 2025

Parkside PIFDS 120 B2 Manual

19 Juni 2025

Gymrex GR-TB 52 Manual

19 Juni 2025

Parkside PBRM 39 C2 Manual

19 Juni 2025

Weidmüller PRO ECO 72W 24V 3A Manual

19 Juni 2025

Parkside PAMFW 20-Li C3 Manual

19 Juni 2025